Micropile Bond Strength to Concrete Fundamental Full Scale Test Program Preliminary Results Allen Cadden, P.E. Jesus Gomez, Ph.D., P.E. Schnabel Engineering,

Slides:

Advertisements

Similar presentations

Drawings for an Oyster Strainer and Drain Pan This design of strainer is required in AOAC International (953.11) for use in determining the drained.

Advertisements

Reinforced Concrete Design

Samrat Mohanty, PhD, PE, Senior Engineer, Agapito Associates, Inc

The Role of the Annular Gap in Expandable Sand Screen Completions SPE J. Heiland, J. Cook, A. Johnson, B. Jeffryes. Schlumberger Cambridge Research.

Presentation about Reinforced concrete

Serviceability Design of Concrete Structures in Marine Environments Carlos E. Ospina, PhD, PE, FACI BergerABAM Inc., Houston, TX 2014 Herbert J. Roussel.

Connection Design.

Micropiles Save Drilled Shafts

Shear - Tensile - Compression Stresses Slip Ted 126 Spring 2007.

Increased load capacity of arch bridge using slab reinforced concrete T.G. Hughes & M. Miri Cardiff School of Engineering Arch 04, Barcelona, Nov ,

AN INTRODUCTION TO MICROPILES CIVL 141 Spring 2011.

Lecture # 2 Allowable Stress Objective:

Introduction – Concept of Stress

ODOT Policy for Deck/Slab Closure Pours Sean Meddles, P.E. Assistant Administrator ODOT Office of Structural Engineering.

1Furmanite Confidential - 1/9/04 Motor and Pump Base Foundational Repair.

NEW DEVELOPMENTS IN FABRICATED TEES – A QUALITY ASSURANCE DESIGN GUIDELINE A.C. Seibi and R. J. Lawrence, GPPA.

IWM 2004 Tokyo, Japan Micropiles State of the Art Report Research and Practice Issues USA John R. Wolosick, P.E. Hayward Baker Inc. Atlanta, Georgia.

Chapter 12 Concrete Construction Part 3 1CE 417, King Saud University.

Institute for Steel Construction – Leibniz University of Hannover 2. PhD Seminar on Wind Energy in Europe October 4th and 5th 2006 at Risø National Laboratory,

GT STRUDL GT STRUDL Users Group 22 nd Annual Meeting & Training Seminar June 24, 2010 Practical Modeling Technique for Transfer Length Chris Carroll, Ph.D.

Slop Stabilization Pertemuan

George F. Limbrunner and Leonard Spiegel Applied Statics and Strength of Materials, 5e Copyright ©2009 by Pearson Higher Education, Inc. Upper Saddle River,

Civil and Environmental Engineering Departments

Bridge Design to AS 5100 Sydney May 25th 2005 Using High Strength Concrete with AS 5100 opportunities and restrictions.

CHE 333 Class 14 True Stress True Strain Crystalline Processes During Deformation.

Design of Concrete Structure I Dr. Ali Tayeh First Semester 2009 Dr. Ali Tayeh First Semester 2009.

Introduction – Concept of Stress

HEWLETT PACKARD BUILDING 5 SEISMIC UPGRADE CORVALLIS, OREGON, USA TOM A. ARMOUR, P.E. SESSION III STRUCTURAL SUPPORT & SEISMIC APPLICATIONS IWM 2002 MAY.

Fundamentals of Structural Detailing

CE A433 – RC Design T. Bart Quimby, P.E., Ph.D. Revised Spring 2009

Building Code Requirements for Structural Concrete (ACI 318M-11) Design of Structures with High-Strength Concrete by ACI 318 David Darwin Vietnam Institute.

Steel Rebar Test Conducted by: Christian Chang Ty Dempsey 5/9/00.

INTRODUCTION Strain gauge measurement is a point strain measurement method developed in the USA c.a independently by E. Simmons and A. Ruge. It.

Research at Northwestern University: End-bearing Micropiles in Dolomite.

Reinforcement Information - Code

Analysis and Design of Reinforced Concrete Beams

Concrete Inspection Construction Inspection for Field Office Activities.

Rapid Construction of Bridge Piers with Concrete Filled Tubes

Summary of Platform and Hilman Rollers Deformation Studies John Amann ILC Mechanical Engineering 7/11/07.

1. Two rods, one of nylon and one of steel, are rigidly connected as shown in Fig. P.1.2. Determine the stresses and axial deformations when an axial load.

PRESSURE VESSEL. 1.Determine the bursting steam pressure of a steel shell with diameter of 10 inches and made of ¼ in thick steel plate. The joint efficiency.

Design and Control of Concrete Mixtures CHAPTER 11

Design Aides for Concrete Masonry Members

Outline Introduction Test section details Axial load test results

Dan Meng, C.K. Lee, Y.X. Zhang*

Presented by: Alex S. Larkin, Jovan Tatar

Lecture 5 - Flexure June 11, 2003 CVEN 444.

PANDA Yoke of the Magnet

of a Novel Pipe Connection

Reinforced Concrete Design

John R. Wolosick, P.E. Hayward Baker Inc. Atlanta, Georgia

André Lubeck; Dr. Gihad Mohamad; Dr. Fonseca, Fernando Soares; PhD.

Drawing Interpretation

A New Precast, Pre-stressed Bridge Deck System

Grout and Other Reinforcement Module

Tensile Testing of Aluminum Alloy

Micropile Bond Strength to Concrete

Reinforced Concrete Design. Compressive Strength of Concrete f cr is the average cylinder strength f’ c compressive strength for design f’ c ~2500 psi.

Chapter 1 Stress and Strain.

Contents Introduction Identification of the knowledge gap

Poisons Ratio Poisons ratio = . w0 w Usually poisons ratio ranges from

True Stress True Strain Crystalline Processes During Deformation.

Structure I Course Code: ARCH 208 Dr. Aeid A. Abdulrazeg

Micropile Implementation: Educating the Practitioners

Structure I Course Code: ARCH 208 Dr. Aeid A. Abdulrazeg.

PDT 153 Materials Structure And Properties

Mechanical Properties Of Metals - I

TxDOT Implementation Project Texas Tech University

Presentation transcript:

Micropile Bond Strength to Concrete Fundamental Full Scale Test Program Preliminary Results Allen Cadden, P.E. Jesus Gomez, Ph.D., P.E. Schnabel Engineering, Inc.

A Privately Funded Research Project – Phase 1

Footing Connection What do you use for the bond stress? Can you prove it? Are you being conservative or unconservative?

Test Summary Tested Steel Bar Tested Steel Casing Tested Casing with Weld Beads Hole Drilled with DHH Type I grout w:c=.45±

Test Setup 4”4”

Block Summary All dimensions in inches. 1 inch = 25.4 mm

Construction

Testing

Preliminary Results Preliminary 1 mm 2.3 mm 3.5 mm 4.8 mm (1.4 MPa)(5.5 MPa)(2.1 MPa)(8.3 MPa) 1 mm 3.5 mm 4.8 mm

Summary Data Preliminary

Conclusions and Request Good bond can be achieved with normal grout Use of 200 psi allowable bond value in typical situations is reasonable. Greater stress and strain to failure was observed with deformed steel surface. Shrinkage may be a concern with larger annulus space. Please provide comparative data if you have any.