A6a to A6b Schematic Diagram to Pictorial Diagram

Slides:



Advertisements
Similar presentations
Basic Electricity.
Advertisements

E1 – Electrical Fundamentals
Thermostats, Pressure Switches, and Other Electric Control Devices
Thermostats. I would recommend that as you proceed through this power point presentation that you refer to your textbook, Unit 14, for some great visuals.
BUrners TRAining CEntre GAS BURNERS N 900 H/L N 900 H/L series.
HVAC Commercial Ref.
Heating Control Devices
Millivolt Troubleshooting Guide Gas Products NOVA SIT Valves 1) Thermocouple Millivolt Check 2) Safety Magnet Testing 3) Thermopile Millivolt Check 4)
HVAC121 – Gas Heat Flame Rectification.
Gas Furnace Controls Part 4.
Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring Diagrams Wiring.
Components, Symbols, and Circuitry of Air-Conditioning Wiring Diagrams
Gas Furnace Controls Part 2.
Student Handout Packet Go to page A4. Please answer the following questions using page A4.
1 HVAC214 – Electrical for Oil Fan Centers. 2 Designed to provide low voltage control of blower motors and auxiliary circuits. Provide a good junction.
Schematic to Pictorial Page A4 schematic to Page A4a pictorial.
1 HVAC 214 Electricity For Oil Heat Fan Center Relays.
7.4.1 Student Book © 2005 Propane Education & Research CouncilPage Identifying the Operating Characteristics of Circuit Control Devices, Electromagnetic.
HYDRONIC HEATING AQUASTATS
THE RELAY. A Relay is an electromagnetic switch. A Relay is activated when a current is applied to it.
Continue The information provided in this training module covers the schematic flow charts for all ovens and ranges that utilized a preheat board, Self.
Chapter 17 Section 3 (pages )
BAKE BROIL - SELECT PROGRAM - CONV BAKE CONV BROIL SELF CLEAN On any diagram screen, double click any of the following components to bring you to a description.
With a knowledge of how to connect cells in parallel and series, we can figure out how to arrange batteries to deliver a desired voltage, and in some cases,
Reading Schematic Diagrams
Unit 4 Symbols.
G1 Supplemental Questions
Zoning Hydronic Systems. Zone Control Divides the Space to be Heated 1.Each with its own heating needs and control systems 2.There are several reasons.
G1 to G1b LOW VOLTAGE Schematic to Pictorial. You will now draw the Pictorial by following the Schematic.
1 HVAC122 - Gas Gas Valves. 2 Solenoid Gas Valves The solenoid gas valve is the simplest of all valves. This valve has an electrical magnetic coil which.
Circuits and Schematic Diagrams Chapter 35. Circuits  ~a set of components that give current a path to follow  You need:  Voltage source  resistor.
BUrners TRAining CEntre GAS BURNERS GS series GS series.
Student Handout Packet – Page A7
BUrners TRAining CEntre GAS BURNERS N 120, 200, 400 N 120, 200, 400 series.
Page A5 Schematic Analysis for Sequence of Operation (AUTOMATIC Spark Ignition System)
PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS Electric Cooling Fans.
Hello there. Smiley, Smasher, and myself will be assisting you as we learn how to wire a mechanical relay circuit. When you are finished with this lesson.
LCD Wiring Diagram Presentation B / B.
Name _______ 6 __ Lesson 6 – Paths of Electricity Jan. __ Objective: to draw and explain 2 paths that electricity can take: 1) __________AND 2) ___________.
G15 This power point presentation is designed to assist the student in understanding the relationship of the fan and limit switch to the fan relay, when.
Glencoe Physics Chapter 23 ”Circuits and Circuit Elements"
G5a Schematic to Pictorial. You will now draw the Pictorial by following the Schematic.
We apply 120 VAC to the HM Unit (Remember to check polarity!) Our primary step down T/X provides power to terminal “X” and “COM” on the ignition control.
BASIC ELECTRICITY AND MAGNETISM
Heating Maintenance and Repair
G7 Schematic to Pictorial. You will now draw the Pictorial by following the Schematic.
Section 6: Air-Conditioning (Heating And Humidification)
K3 Schematic Analysis and Pictorial Diagram
Gas Furnace Controls Part 1.
GAS BURNERS R 40 GS 20 H/L.
K4 Schematic Analysis and Pictorial Diagram
K1 Schematic Analysis and Pictorial Diagram
Schematic to Pictorial
Schematic to Pictorial
K2 Schematic Analysis and Pictorial Diagram
Please retrieve a copy of page A8 from the Student Handout Packet.
K5 Schematic Analysis and Pictorial Diagram
Schematic to Pictorial
K6 Schematic Analysis and Pictorial Diagram
Schematic to Pictorial
Schematic to Pictorial
Current Electricity and Electric Circuits
Schematic to Pictorial
Schematic to Pictorial
Presentation transcript:

A6a to A6b Schematic Diagram to Pictorial Diagram

Turn to page A6a and A6b in the Student Handout Packet Turn to page A6a and A6b in the Student Handout Packet. If you have NOT viewed the power point presentation entitled ‘glow coil’, please do so BEFORE you continue on with this schematic to pictorial.

You will now draw the Pictorial by following the Schematic

Follow the schematic to wire the pictorial Follow the schematic to wire the pictorial. Please complete YOUR page A6b as you proceed through the following slides.

24v from the ‘P’ terminal goes to the ‘R’ terminal of the terminal strip, then to the thermostat and back from the thermostat to the ‘W’ terminal of the terminal strip. P C

P C Please mark the P and C terminals on the control transformer.

P C There is NO terminal strip so go directly to the thermostat.

24v continues on to the ‘Fan Time Delay Switch.’ P C

P C

24v continues on to the ‘Limit Switch.’ P C

P C

24v continues on to the gas valve. P C

P C

24v continues from the gas valve to the NO terminal of the Baso switch, which they are calling the ignitor relay (same thing). P C

P C

We are going to back up and start again at the ‘P’ terminal of the control transformer. We come out of the ‘P’ terminal and go to the ‘Pilot Pressure Switch.’ P C

P C

We come out of the pilot pressure switch and go to the ignition transformer primary.

P C

We come out of the primary of the ignition transformer and go to the NC terminal of the Baso switch.

P C

We come out of the C terminal of the Baso and go to the C terminal of the control transformer. P C

P C

Add two wires from the ignition transformer to the ignitor (glow coil). P C

P C

You have finished the heating low voltage circuits pictorial following a schematic

The end