Plate No. 5

Make the Border line and Title Block – (5 Minutes ONLY) Divide the workspace and find the reference point – (5 Minutes ONLY) Draw the Isometric Axis – (5 Minutes Only)

Making Border line and Title Block 15 mm from Edge of paper

Construction of BORDER LINE 15 mm from Edge of paper FROM ALL SIDES

Construction of TITLE BLOCK 15 mm above the Lower Border Line

100 mm 200 mm 265 mm 330 mm Divide the Title Block with the given length Construction of TITLE BLOCK

5mm in Height Construction of TITLE BLOCK Draw 5 mm guideline for the title block DATA

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: Complete the details in the Title Block Construction of TITLE BLOCK

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: Divide the workspace into mm 125 mm

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: From the reference point 100 mm 20 mm Reference point

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: From the reference point draw the 30  angle line using the triangle.

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: From the reference point draw the 30  angle line using the triangle.

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: From the reference point draw the 30  angle line using the triangle.

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: Isometric Axis is now complete. REMEMBER: Use THIN lines only for guidelines and construction lines

NAME:MOHAMMED AL SHAMSITITLE: PLATE NO. 3 SECTION: DATE: SCALE: Start your work from the reference point.

“Model” or “Task” Height=35Depth=45Width=35Height=35Depth=45Width=35

Mark the dimension from the axis. 10 mm Height=35Depth=45Width=35Height=35Depth=45Width=35 Height= 35

Mark the dimension from the axis. 10 mm Height=35Depth=45Width=35Height=35Depth=45Width=35 Width= 35

Mark the dimension from the axis. 10 mm Height=35Depth=45Width=35Height=35Depth=45Width=35 Depth = 45

Draw Construction Line. Project upward from Mark 45mm

Draw Construction Line. Project upward from Mark 35mm

Draw Construction Line. Draw 30  line to left as taken from “Model”

Draw Construction Line. Draw 30  line to right as taken from “Model”

Mark the dimension from the axis. Mark 10 mm from the last line

Mark the dimension from the axis. Mark 10 mm from the last line

Draw Construction Line. Project line upward

Draw Construction Line. Project line upward

Draw Construction Line. Draw 30  line to left as taken from “Model”

Draw Construction Line. Draw 30  line to left as taken from “Model”

OBJECT LINE Draw OBJECT LINE. Draw OBJECT Line as copied from the Model

Draw Construction Line. Draw 30  line to right as taken from “Model”

Draw Construction Line. Draw 30  line to right as taken from “Model”

Draw Construction Line. Draw 30  line to left as taken from “Model”

Draw Construction Line. Draw 30  line to left as taken from “Model”

OBJECT LINE Draw OBJECT LINE. Draw OBJECT Line as copied from the Model

Draw Construction Line. Draw OBJECT Line as copied from the Model

Draw Construction Line. Draw OBJECT Line as copied from the Model

OBJECT LINE Draw OBJECT LINE. Draw OBJECT Line as copied from the Model

Finish That was EASY Try the NEXT Execise on your own. FOLLOW SAME PROCEDURE

Try This! Observe Diension. Height=35Depth=45Width=35Height=35Depth=45Width=35

Try This! Get the Dimension yourself Height= ? Depth= ? Width= ? Height= ? Depth= ? Width= ? Answer:Height=30Depth=40Width=50Answer:Height=30Depth=40Width=50

Try This! Get the Dimension yourself Height= ? Depth= ? Width= ? Height= ? Depth= ? Width= ?

GOOD LUCK