Boundary Layer Correction Air enters a two-dimensional wind tunnel as shown. Because of the presence of the boundary layer, fluid will be displaced away.

Slides:

Advertisements

Similar presentations

Motion and Force A. Motion 1. Motion is a change in position

Advertisements

Drag and Momentum Balance

Experiment #5 Momentum Deficit Behind a Cylinder

ES 202 Fluid and Thermal Systems Lecture 28: Drag Analysis on Flat Plates and Cross-Flow Cylinders (2/17/2003)

Pipe Flow Example Water flows steadily into the circular pipe with a uniform inlet velocity profile as shown. Due to the presence of viscosity, the velocity.

Shell Momentum Balances

External Convection: Laminar Flat Plate

Continuity of Fluid Flow & Bernoulli’s Principle.

..perhaps the hardest place to use Bernoulli’s equation (so don’t)

Motion of particles trough fluids part 2

Pharos University ME 352 Fluid Mechanics II

MECH 221 FLUID MECHANICS (Fall 06/07) Tutorial 9

a) The kinetic energy of the car. b) The distance it takes to stop.

Internal Flow: Heat Transfer Correlations

Fluid Dynamics.

Study of Liquid Breakup Process in Solid Rocket Motors Author: Michael Stefik & Bryan Sinkovec, Co-Author: Yi Hsin Yen, Faculty Advisor: Professor Ryoichi.

Flow Over Immersed Bodies

0.1m 10 m 1 km Roughness Layer Surface Layer Planetary Boundary Layer Troposphere Stratosphere height The Atmospheric (or Planetary) Boundary Layer is.

Quanitification of BL Effects in Engineering Utilitites… P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Engineering Parameters.

1 Example of Groundwater Primer - Yours will be fluid mechanics primer – see homework assignment sheet

Notes Reminder: please turn in HW, pick up new one Reminder: First Exam next Friday, 1:55-3:50pm, Jordan Hall lab room – Will cover Gravity, Fluids (Ch.13,

Pgs  Calculate the pressure exerted by a fluid.  Explain Pascal’s Principle.  Calculate how pressure varies with depth in a fluid.

Momentum Heat Mass Transfer

Fixed and Fluidized Beds

© 2011 Autodesk Freely licensed for use by educational institutions. Reuse and changes require a note indicating that content has been modified from the.

Basic bluff-body aerodynamics II

Practical Applications Wind Turbine Hydropower Turbine The motion of a fluid is altered so that propulsive forces can be generated on the devices. The.

Ch Ch.15 Term 061. Ch-12  T061  Q16. The volume of a solid Aluminum sphere at the sea level is V = 1.0 m3. This sphere is placed at a depth of.

Basic Fluid Properties and Governing Equations

Hard Starch Problem 13.. Introduction Work devided in four steps Achiveing effect Necessary equipment construction Measurement Theoretical model development.

Mass Transfer Coefficient

Chapter 6 Introduction to Forced Convection:

Drag and Lift E80 Fluid Measurements Spring 2009.

Fluid Report Presentation Onur Erkal Korgun Koyunpınar Korhan Türker Hakan Uzuner.

Boundary Layer Control with Injection and Suction Through a Porous Wall By Crisen McKenzie.

Basic Fluid Properties and Governing Equations  Density (  ): mass per unit volume (kg/m 3 or slug/ft 3 )  Specific Volume (v=1/  ): volume per unit.

Ekman Flow September 27, 2006.

Fluid Resistance.

Jan cm 0.25 m/s y V Plate Fixed surface 1.FIGURE Q1 shows a plate with an area of 9 cm 2 that moves at a constant velocity of 0.25 m/s. A Newtonian.

Nazaruddin Sinaga Laboratorium Efisiensi dan Konservasi Energi Fakultas Teknik Universitas Diponegoro.

BOUNDARY LAYERS Viscous effects confined to within some finite area near the boundary → boundary layer In unsteady viscous flows at low Re (impulsively.

 ~ 0 [u(x,y)/Ue] (1 – u(x,y)/Ue)dy

Chapter 7 External Convection

THERMAL ANEMOMETER MEASUREMENT The Kurz thermal anemometers use two RTDs, one heated 50 to 100’C above the ambient. The other monitors the ambient. The.

External Flows An internal flow is surrounded by solid boundaries that can restrict the development of its boundary layer, for example, a pipe flow. An.

CE 1501 Flow Over Immersed Bodies Reading: Munson, et al., Chapter 9.

Stokes Solutions to Low Reynolds Number Flows

PHAROS UNIVERSITY ME 253 FLUID MECHANICS II

Chapter 7 Natural convection systems. 7-1 Introduction  natural or free convection: the motion of the fluid due to density changes arising from heating.

Boundary Layer on a Flat Plate: Blasius Solution H z from Kundu’s book Assuming displacement of streamlines is negligible →u = U = constant everywhere,

Flow Similarity and Model Testing Geometrical similarity: similar geometry. Kinematic similarity: flow pattern around the model should be similar to...

Governing Equations in Differential Form Take the limit such that the control volume approach to infinitesimal small: consequently, all fluid properties.

Heat Transfer Su Yongkang School of Mechanical Engineering # 1 HEAT TRANSFER CHAPTER 7 External flow.

Gravitational Force  Gravity= a force of attraction between objects, “pulls” objects toward each other  Law of universal gravitation= all objects in.

Chapter 11 Fluids.

Internal Incompressible

Energy Loss in Valves Function of valve type and valve position

Playland Project 2-2 Sirada, Simon, Rosemary

Motion Graphs Position-Time (also called Distance-Time or Displacement-Time) d t At rest.

Fluid Mechanics & Hydraulics

Free Fall Free Fall Examples

External Flows An internal flow is surrounded by solid boundaries that can restrict the development of its boundary layer, for example, a pipe flow. An.

Motion and Force A. Motion 1. Motion is a change in position

Graphing Motion Walk Around

Governing Equations in Differential Form

Section 8, Lecture 1, Supplemental Effect of Pressure Gradients on Boundary layer • Not in Anderson.

Fundamentals of TRANSPORT MECHANISMs

Boundary Layer Correction

Presentation transcript:

Boundary Layer Correction Air enters a two-dimensional wind tunnel as shown. Because of the presence of the boundary layer, fluid will be displaced away from the surface. In order to maintain a constant velocity inside the tunnel, it is necessary to increase the cross-sectional size of the tunnel. (a) Determine the channel height, H(x), as a function of the distance measured from the inlet of the tunnel, x. The tunnel velocity is 10 m/s and the tunnel inlet height is 5 m. Assume the boundary layer has a profile u(y)=U  sin(  y   b  What is the momentum thickness  (x) of the boundary layer flow.

Boundary Layer Correction (cont.)

 c) If a sphere has a diameter of 0.1 m is placed in the center of the wind tunnel, what is the drag force exerted on the sphere.  air =1.2 kg/m 3, =1.5x10 -5 m 2 /s. Use the following graph for C D verse Re data.