Dimensioning A dimensioned drawing should provide all the information necessary for a finished product or part to be manufactured. An example dimension.

Slides:

Advertisements

Similar presentations

Let’s make engineering more easy

Advertisements

Surface Finish An engineering component may be cast, forged, drawn, welded or stamped, etc. All the surfaces may not have functional requirements and need.

Tangents- Definition Geometric Constructions A line is a tangent to a circle if it touches the circle at only one point.

Equation of Tangent line

10.1 Tangents to Circles.

Geometric Construction Notes 2

Shawlands Academy Department Of Technical Education

Circle. Circle Circle Tangent Theorem 11-1 If a line is tangent to a circle, then the line is perpendicular to the radius drawn to the point of.

Lesson 3 J.Byrne Tangent A line touches a circle at one point on the circumference. It is called a Tangent. The point of contact is called the POC.

S3 BLOCK 8 Angles and Circles I can find the size of a missing angle using the following facts. Angle in a semi circle. Two radii and a chord form an isosceles.

Circles – Tangent Lines A tangent line touches a circle at exactly one point. In this case, line t is tangent to circle A. t A.

Chapter 7 Dimensioning.

Module 4: Isometric Drawing

Dimensioning and Tolerancing

Parallel & Perpendicular Lines. Parallel and Perpendicular Lines The two lines shown below are parallel (never intersect). Identify the slope of each.

Copyright © 2014 John Wiley & Sons, Inc. All rights reserved.

constructions The Perpendicular bisector of a Line.

EXAMPLE 1 Write an equation of a circle Write the equation of the circle shown. The radius is 3 and the center is at the origin. x 2 + y 2 = r 2 x 2 +

Dr. R. Ribeiro, Mechanical Engg. Dept. IITD

Dimensioning & Scaling

Parallel-Axis Theorem

Dimensioning (WEEK 2).

Graphic boclair academy SECTIONAL VIEWS.

Introduction Geometric figures can be graphed in the coordinate plane, as well as manipulated. However, before sliding and reflecting figures, the definitions.

Unit 5 Vocab By: Mika Hamady. Acute Angle Definition: An acute angle is an angle that is less then 90 degrees. Examples: 1.A 43 degree angle is acute.

Coatbridge High School Tangency 2 Lines A Curve Tangential to 2 Lines Draw two arcs with the centre on the lines Draw two lines parallel to the other.

Graphic Communication

 The tangent theorem states that if two segments are tangent to a circle and intersect one another, the length from where the segments touch the circle.

CIRCLES: TANGENTS. TWO CIRCLES CAN INTERSECT… in two points one point or no points.

ENGR 214 Chapter 15 Kinematics of Rigid Bodies

Greenfaulds High School Orthographic Views. Orthographic Projection Orthographic projection is the name given to the type of drawing where a 3D object.

DIMENSIONING Sizing of drawings in Drafting has standards and guidelines.

Circle Properties. Draw a Circle Draw a Chord Draw radii from ends of chord Draw lines from each end of line to meet on circumference a b Measure angles.

Drawing Abilities Teacher

SECTIONAL VIEWS.

Shape and Space CIRCLE GEOMETRY. Circle Geometry Rule 1 : ANGLE IN A SEMICIRCLE = 90° A triangle drawn from the two ends of a diameter will always make.

SUBMITTED BY ROSHNI B S. Circle is a closed curve in a plane A circle can be drawn with the help of a circular object.

Elements of Art. ELEMENTS OF ART KIM Elements of Art The different parts that make up any piece of art.

Equations of Circles. You can write an equation of a circle in a coordinate plane, if you know: Its radius The coordinates of its center.

Lesson 1 J.Byrne Parts of a Circle A circle is a plane figure that has one continuous line called its Circumference. A straight line that touches.

FOCAL PLANE MECHANISM Dr. N. VENKATANATHAN.

Engineering drawing Every language has its own rules of grammar. Rules of grammar : Lines, lettering, and dimensioning.

Line of sight is an imaginary ray of light between an observer’s eye and an object. Line of sight Parallel projection Line of sight Perspective projection.

Lesson 2 J.Byrne Circles in Contact Externally When circles are touching at one point on their circumference they are said to be in contact tangentially.

Graphic st. aidans high DIMENSIONING.

EXAMPLE 1 Write an equation of a circle Write the equation of the circle shown. SOLUTION The radius is 3 and the center is at the origin. x 2 + y 2 = r.

Isometric Circle using the Ordinate Method

Straight lines tangent to circles. Find the perpendicular bisector between the centres Draw arc from bisector through centres.

Sizing of drawing in drafting Has standard and guidelines.

Isometric Circle using the Ordinate Method

Inscribed and Circumscribed Figures

Graphic Communication

A Sectional View shows what is going on inside an object

What are Dimensions? Dimensions are the text that is provided with a drawing that describe the exact size and location for the features shown. Also known.

ORTHOGRAPHIC PROJECTION

Graphing Ordered Pairs

Chapter 3 DIMENSIONING Dimensioning refers to the act of giving dimensions. Dimension is a numerical value expressed in appropriate units of measurement.

Grand Prix Racing Circuit

DIMENSION PLACEMENT By: Muhammad Zahid.

Technical drawing Workshop Practice E102A.

ORTHOGRAPHIC PROJECTION

Graphing on the Coordinate Plane

CHAPTER 3 Dimensioning.

Using British Standards

Graphing on the Coordinate Plane

Graphic Communication

Using British Standards

Chapter 2 Lines.

Slope Graphing Day 2.

Presentation transcript:

Dimensioning A dimensioned drawing should provide all the information necessary for a finished product or part to be manufactured. An example dimension is shown below. Dimensions are always drawn using continuous thin lines. Two projection lines indicate where the dimension starts and finishes. Projection lines do not touch the object and are drawn perpendicular to the element you are dimensioning. All dimensions less than 1 should have a leading zero. i.e..35 should be written as 0.35

Types of Dimensioning Parallel Dimensioning Parallel dimensioning consists of several dimensions originating from one projection line.

Superimposed Running Dimensions Superimposed running dimensioning simplifies parallel dimensions in order to reduce the space used on a drawing. The common origin for the dimension lines is indicated by a small circle at the intersection of the first dimension and the projection line.

Chain Dimensioning Combined Dimensions A combined dimension uses both chain and parallel dimensioning.

Dimensioning of circles (a) shows two common methods of dimensioning a circle. One method dimensions the circle between two lines projected from two diametrically opposite points. The second method dimensions the circle internally. (b) is used when the circle is too small for the dimension to be easily read if it was placed inside the circle.

Dimensioning Radii All radial dimensions are proceeded by the capital R. (a)shows a radius dimensioned with the centre of the radius located on the drawing. (b) shows how to dimension radii which do not need their centres locating.