The Blades and Motor Presented by Jeffrey Wu. Objective: To understand the blades and the motor of a reciprocating saw. Definition: A portable power saw.

Slides:

Advertisements

Similar presentations

Electric Strike Selection and Installation By: Michael D. Vorpahl, CRL Capital Lock, Inc Regent St. Madison, WI Phone: Fax:

Advertisements

Types of saw blades Crosscut –used to make smooth cuts across the grain Rip –used to make smooth fast cuts with the grain Combination –used to make fast.

Unit 3 Day 2: Resistivity, Power & AC Current Resistivity and its Temperature Dependence Electric Power Heat Generation in Electric Circuits AC Current.

1 Copyright  2004 Lincoln Global Inc. Shielded Metal Arc Welding SMAW(Stick)

Hardware, Lawn & Garden. Mowers 20” Cordless Electric Mower Model Volt System 3 IN 1 - Mulch - Side Discharge - Rear Bag Single Lever Height.

Jeopardy Jeopardy PHY101 Chapter 7 Review Study of Electricity By Cheryl Dellai.

In this activity we’ll discover the relationship between electricity and magnetism and find out just what makes a motor work. The electric motor converts.

Parallel Circuit electricity has more than one path to follow total amps are equal to the sum of the individual amps total watts are equal to the sum of.

What is Electricity? Electricity is the flow of moving electrons. When the electrons flow it is called an electrical current.

Intro to Power Tools. Electric Tools Pneumatic Tools.

Portable Power Tools Unit 14 Page 180

 stone work  Masonry is the building of structures from individual units laid in and bound together by mortar; the term masonry can also refer to the.

 Rate (how fast) at which charges pass a given point  Measured in Amperes or amps  Current (I)  Electrons moving in a wire make up current and provide.

14.4 V Cordless Master craft Reciprocating Saw By Hussein Ebrahim Monday, November 15, 2005 Objective: To explain components of a reciprocating saw and.

Chain saw By Ali Al Thani.

BRUSHLESS HIGH VELOCITY RACING FAN. Brushless high velocity racing fan  Brushless direct current motor  13.8 volt (working range 10-16v)  Current:

Electric Circuits Part Two: Current and Voltage Learning Goals  Explain how current flows in an electric circuit.  Define voltage and describe how.

Handsaws Types & Uses. Crosscut vs. Rip cut Two saws that look the same ….but are very different. Why.

PRINCIPLES OF ELECTRICITY

1 Block Diagramming Donald Heer 10/21/09. 2 Overview Block Diagrams Decomposition Interface Definitions.

POWER SAWS Two main categories of power saws: Portable & Stationary. Work is fed into a stationary saw. Saws that are fed into the work are portable. Smaller.

Ohms Law Problems.

UNIT V STUDY GUIDE Electricity & Magnetism

Electricity What is it and how does it work?. Some definitions to start with An electrical current is caused by the flow of negatively charged electrons.

Current Electricity - Symbols Draw the symbol for each electrical device.

Specifications and Blade Types OBJECTIVE: give basic facts on the reciprocating saw tool. By: Phuong Dinh Points of Discussion Definitions Types of Reciprocating.

Types of heater: Gas Why Use Gas-fired Heating Equipment ä Most economical heating source ä Wide variety of equipment available ä Most common source.

By Angel Acevedo The Question  #1: Fabian has a wooden board that is 13 feet long. He uses an electric saw to cut the board into five pieces. Every.

Objective Compute electrical energy and cost.

Reciprocating Saws Objective: Provide a general understanding of reciprocating saws and their use. By: Derek Landschoot References:

1 The Reciprocating Saw Farhan Mahmood. 2 Objective What the saw is Applications Blade types To give a brief understanding of:

U3e-L3 1.Why are the + and – symbols unnecessary when drawing the power source in an electric schematic? 2.A ______ circuit occurs when the positive terminal.

16.2 Current and Voltage. Electric Current (review from yesterday) Electric current: the flow of electric charge (movement of electrons)

Amperes, Volts and Ohms. We use different units to measure different things: We use different units to measure different things: Time – minutes Time –

Grapefruit Powered Light Jason Fox MEEN Instructions To start the procedure I used Zinc coated 3.5 inch nails and Copper out of a neomex electrical.

Electrical Tool Bid B All Items are to be bid in same branding. Alternates are not accepted. It is permissible to utilize “combo packs” with hand.

What do you think? What do you think these four pictures have in common?

MasterCraft 14.4v Cordless Reciprocating saw Sean McCallion.

The AC Power Grid 60 Hz, 120 V RMS. DC vs. AC Thomas Edison - DCWestinghouse - AC VS. In the late 1800s, these two guys fought fiercely over the power.

Intro to Power Tools. Electric Tools Pneumatic Tools.

ELECTRICAL RECEPTACLES

Comparing AC-DC and Transformer Rectifier Welders

5 Chapter Power Tools. 5 Chapter Power Tools Objectives Identify common power tools. Explain the function and operation of a carpenter’s principal.

Exhaust, Electrical, and Ignition.

Learning Objectives I can describe electric current and how voltage is applied to that current. I can compare direct current to alternating current and.

Electric Current Introduction

U3e-L12 March 31, 2008 DRILL A 75-watt light bulb is plugged into a wall socket (120V AC). What is the current going through the light bulb? (Use Joule’s.

U3e-L3 February 25, 2010 DRILL Why are the + and – symbols unnecessary when drawing the power source in an electric schematic? A ______ circuit occurs.

What is a Generator?

Machine tools and their applications

Five-Minute Check (over Lesson 3–2) Mathematical Practices Then/Now

How Does Reciprocating Saw Work?

Circuit Introduction Section 1:

Electrical Potential Joules units: = Volt = V Coulomb

1/7: WU : Answer the scale questions below

GCF Problem Solving How can you tell if a word problem requires you to use Greatest Common Factor?

Presented By: Saif Ahmed

Transformers A transformer changes the high voltage from the main power lines to the 120 volts your appliances use.

Without a calculator, find the indicated value.

Impart knowledge concerning reciprocating saw

Write the complement and supplement of each angle.

Complete each trigonometric identity. Factor each expression.

Electric Current and Electrical Energy

Alternating Currents Electricity Tutorial 9.

Chapter Twenty: Electric Circuits

Components of a Reciprocating saw

Arc Welding – Part II AG 221 – Metals and Welding.

LESSON-13 STRAIGHT KNIFE CUTTER

Some Thoughts On Circulator Selection

Presentation transcript:

The Blades and Motor Presented by Jeffrey Wu

Objective: To understand the blades and the motor of a reciprocating saw. Definition: A portable power saw with a reciprocating blade; can be used with a variety of blades depending on the application and kind of cut.

Are versatile and will accept a wide variety of saw blades Different type of blades for different cutting objects The blade mounting is standard Length from 3 to 8 inches

Cordless Reciprocating Saw Non-Cordless Reciprocating Saw amps 6 amps amps 9.6 volts - 18 volts volts Reach more places Unlimited using time

Number of strokes is measured per minute Stroke length

Universal motor AC or DC electric power Loud Smaller and much lighter

References : AJ2CQHUBSCHPQKA4QHQJCK?prodId=IrwinProd %20Saws% pdf