TROWEL-DOWN OVERLAYMENT APPLICATION TROWEL-DOWN

THE BENEFITS OF OVERLAYMENT REPAIR EXISTING SURFACES PROFITABLE ELIMINATE REMOVAL SAVES TIME ON EXISTING SURFACES TRANSFORMS EXISTING SURFACES TO GIVE THE APPEARANCE OF BRICK, TILE OR STONE

TROWEL-DOWNAPPLICATION PREPARE YOUR SURFACEPREPARE YOUR SURFACE PRIME WITH PRIMER USING A PUMP SPRAYERPRIME WITH PRIMER USING A PUMP SPRAYER APPLY YOUR BASE COAT USING OVERLAY MIX (GRAY OR WHITE)APPLY YOUR BASE COAT USING OVERLAY MIX (GRAY OR WHITE) TROWEL OR SQUEEGEE YOUR BASE COAT THE WIDTH OF THE STENCILTROWEL OR SQUEEGEE YOUR BASE COAT THE WIDTH OF THE STENCIL 60 POUNDS COVERS UP TO 56 SQUARE FEET AT 1/8” THICK60 POUNDS COVERS UP TO 56 SQUARE FEET AT 1/8” THICK

STENCIL ADHERE THE STENCIL TO THE TACKY BASE COATADHERE THE STENCIL TO THE TACKY BASE COAT REPEAT THE PROCESS UNTIL THE ENTIRE STENCIL IS LAIDREPEAT THE PROCESS UNTIL THE ENTIRE STENCIL IS LAID

COLOR COAT/TOP COAT COLORPAX DRY PIGMENT DRY PIGMENT PRE-MEASURED PRE-MEASURED MIXES DIRECTLY INTO OVERLAY MIX MIXES DIRECTLY INTO OVERLAY MIX LIQUID COLOR LIQUID PIGMENTLIQUID PIGMENT MIXES DIRECTLY INTO OVERLAY MIXMIXES DIRECTLY INTO OVERLAY MIX

IF BASE COAT IS DRY, RE-APPLY PRIMER WITH PUMP SPRAYERIF BASE COAT IS DRY, RE-APPLY PRIMER WITH PUMP SPRAYER APPLY THE TOP COAT USING OVERLAY MIX MIXED WITH THE DESIRED COLORANTS (LIQUID COLOR OR COLORPAX)APPLY THE TOP COAT USING OVERLAY MIX MIXED WITH THE DESIRED COLORANTS (LIQUID COLOR OR COLORPAX) THINLY TROWEL THE TOPCOAT OVER THE STENCIL (ABOUT 1/8 OF AN INCH THICK)THINLY TROWEL THE TOPCOAT OVER THE STENCIL (ABOUT 1/8 OF AN INCH THICK) APPLYING COLOR COAT

RELEASE AGENT IS THEN APPLIED AND THE SURFACE TEXTUREDRELEASE AGENT IS THEN APPLIED AND THE SURFACE TEXTURED CLEAR LIQUID RELEASE OR COLORED POWDER RELEASE MAY BE USEDCLEAR LIQUID RELEASE OR COLORED POWDER RELEASE MAY BE USED DO NOT ALLOW THE RELEASE AGENT TO GET ON THE BASE COATDO NOT ALLOW THE RELEASE AGENT TO GET ON THE BASE COAT TO ALLOW TEXTURING, RELEASE MUST BE APPLIED IMMEDIATELY AFTER THE TOPCOAT, BECAUSE IT SETS UP QUICKLYTO ALLOW TEXTURING, RELEASE MUST BE APPLIED IMMEDIATELY AFTER THE TOPCOAT, BECAUSE IT SETS UP QUICKLY TEXTURING

REMOVE STENCIL AS SOON AS THE OVERLAY CHIPS FREELY FROM THE STENCIL (SAME-DAY)REMOVE STENCIL AS SOON AS THE OVERLAY CHIPS FREELY FROM THE STENCIL (SAME-DAY) USE A WIRE BRUSH TO DETAIL JOINTSUSE A WIRE BRUSH TO DETAIL JOINTS DO NOT LEAVE STENCIL IN OVERNIGHTDO NOT LEAVE STENCIL IN OVERNIGHT ALLOW TO CURE FOR 48 HOURS BEFORE CLEANING YOUR SURFACEALLOW TO CURE FOR 48 HOURS BEFORE CLEANING YOUR SURFACE PULLING YOUR STENCIL

CONTINUE WITH THE SAME STEPS AS FOR CAST-IN-PLACE — WITH THE EXCEPTION OF SEALINGCONTINUE WITH THE SAME STEPS AS FOR CAST-IN-PLACE — WITH THE EXCEPTION OF SEALING IT IS CRITICAL TO SEAL ACCORDING TO THE OVERLAY MANUFACTURER’S SPECIFICATIONSIT IS CRITICAL TO SEAL ACCORDING TO THE OVERLAY MANUFACTURER’S SPECIFICATIONS CLEAN & SEAL