Test Your Knowledge- What is Wrong??. 1. What is wrong with the placement location of these dimensions? The longer dimensions have been positioned inside.

Slides:

Advertisements

Similar presentations

Let’s make engineering more easy

Advertisements

Dimensioning Dimensioning Gateway To Technology®

How to annotate simple drawings for use in constructing an object

Chapter 7 Dimensioning.

Chapter 7 Dimensioning.

Dimensioning part 2 with SolidWorks

CE En 112 Engineering Drawing with CAD Application

Drafting and Dimensioning Standards

CHAPTER 4 Dimensioning.

Technological Systems Unit 1 ~ How They Work Lesson 1 ~ Exploring Technological Systems Technical Sketching.

Dimensioning Standards

Dimensioning Guidelines

Ch.9 Dimensioning Why do we need dimensions? Important elements of a dimensioned drawing Dimension text placement Unidirectional vs. aligned dimensions.

DIMENSIONING The dimension line should be approximately 3/8” from the object and the extension lines should extend 1/8” beyond the dimension line. The.

Introduction to SolidWorks

Dimensioning Standards

Aberdeen Grammar School Isometric Views. Isometric Drawings Lengths and breadths are drawn at 30° to the horizontal. Heights are drawn vertically. All.

Dr. R. Ribeiro, Mechanical Engg. Dept. IITD

Dimension Guidelines. 1. Dimensions should NOT be duplicated, or the same information given in two different ways. Incorrect.

Dimensioning Dimensioning.

Introduction to Dimensioning

Dimensioning (WEEK 2).

Dimensioning Standards

Dimensioning Dimensioning Gateway To Technology®

Dimensioning Dimensioning.

ENTC 1110 OBLIQUE PICTORIALS.

1 SheetCourse: Engineering Graphics 1504Memorial University of Newfoundland Engi 1504 – Graphics Lecture 5: Sectioning and Dimensioning l Sectioning an.

DIMENSIONING Sizing of drawings in Drafting has standards and guidelines.

Basics of Mechanical Drawing and Dimensioning ChE 126 Borrowed mostly from the Fundamentals of Engineering Honors program at Ohio State 1.

To begin click: File, New, then select Design Familiarize yourself with the controls on the page. Then use the maximise button the make the window fill.

Dimensioning Guidelines

Dimensioning Guidelines

Drawing Abilities Teacher

Dimension Guidelines (Material developed by Project Lead the Way)

Dimensioning Guidelines

Technological Design Basic Dimensioning with AutoCAD How to annotate simple drawings for use in constructing an object.

Dimensioning with SolidWorks

Dimensioning Technical Drawing Stuarts Draft High School.

Percent Change of Dimensions Lesson 71. Increase and Decrease ›Increase: Dilation ›Decrease: Reduction ›Creates similar figures; proportional measures.

Introduction to Engineering Introduction to Isometric Ellipse Agenda: Sketching of ellipse for isometric drawings Introduce concepts and conventions of.

Isometric Views.  Lengths and breadths are drawn at 30° to the horizontal.  Heights are drawn vertically.  All sizes are drawn to their exact sizes.

Dimensioning. Why Dimension?  Size and  Location of all features Engineers, designers, and engineering technologists need to know.

Introduction to Dimensioning © 2012 Project Lead The Way, Inc.Introduction to Engineering Design.

Dimensioning © 2011 Project Lead The Way, Inc.Design and Modeling.

Which is best Isometric view

Orthographic Projections Mr. Johanson Technology Education Blue Mountain Middle School.

Detail Drawings Suggested Layouts Dimensioning Guidelines

Basic Dimensioning.

Learning Objectives Define the following: Dimension line, Extension line, Reference dimension, and Leader Be able to understand the basic rules of dimensioning.

Dimensioning Standards and Techniques. Organizations for Dimension Standards American National Standards Institute – a U.S. organization that recommends.

Graphic Communication

General Rules of Dimensioning

Dimensioning part 2 with SolidWorks

Drawing Abilities Teacher

Dimension Styles Dimension Styles.

Chapter 3 DIMENSIONING Dimensioning refers to the act of giving dimensions. Dimension is a numerical value expressed in appropriate units of measurement.

Dimensioning Fundamentals

Dimensioning Standards

WORKING DRAWINGS Footer Text 11/14/2018.

Dimensioning part 2 with SolidWorks

Dimensioning Standards

Dimensioning part 2 with SolidWorks

Dimensioning Fundamentals

Introduction to Dimensioning

Introduction to Dimensioning

Dimensioning Standards

Dimensioning Standards

Dimensioning Guidelines

Introduction to Dimensioning

Presentation transcript:

Test Your Knowledge- What is Wrong??

1. What is wrong with the placement location of these dimensions? The longer dimensions have been positioned inside of the shorter dimensions.

2. What is wrong with the placement location of these dimensions? Dimensions should be located outside the object lines whenever possible to avoid confusion.

3. What is wrong with the dimensions below? The drawing is over dimensioned. It is not necessary to include the inside shorter dimensions.

4. What is wrong with the dimensions below? The drawing is over dimensioned. Do not repeat dimensions. They are represented only once.

5. What is wrong with the dimensions below? The dimensions are difficult to read on the right view. They should be placed on the left view.

6. What is wrong with the dimensions below? The dimension’s text should not be on the object line. Makes the dimension difficult to read.

7. What is wrong with the dimensions below? The circular dimension should be dimensioned as a diameter not a radius. The radial dimension should be dimensioned as a radius not a diameter.

8. What is wrong with the dimensions below? The vertical dimension is needed to locate the beginning of the slant.

9. What is wrong with the dimensions below? The angular dimension is difficult to read. It should be positioned off the object line.

10. What is wrong with the dimensions below? Avoid dimensioning hidden lines and poor referencing of vertical dimensions.

11. What is wrong with the dimensions below? Dimension between views whenever possible. A better dimensioning practice.

12. What is wrong with the dimensions below? The dimension locations are fine on this drawing. What can be done to improve it? This is an engineering drawing. Decimals units would be better.

13. What is wrong with the dimensions below? You cannot locate the proper locations for the proper position of the holes on the radial dimension without the angular distance. Angular Dimensions

14. What is wrong with the dimensions below? The right side view and the isometric view are not necessary to complete this drawing. The overall length of 4.75 is also not necessary to complete this drawing.

15. What is wrong with the dimensions below? Dimensions should be placed on the contour view for clarity.