Design Process 1.Selection of the type of structural form to be used and the material out of which the structure is to be made. 2.Determination of the.

Slides:

Advertisements

Similar presentations

Limit States Flexure Shear Deflection Fatigue Supports Elastic Plastic

Advertisements

Design should address: UNDERSTRENGTH OVERLOAD

An-Najah National University

Chp12- Footings.

Lecture 9 - Flexure June 20, 2003 CVEN 444.

Design of Concrete Structure I Eng. Tamer Eshtawi First Semester 2008 Eng. Tamer Eshtawi First Semester 2008.

Reinforced Concrete Design

Reinforced Concrete Flexural Members

Design of Concrete Structure I

ONE-WAY SLAB. ONE-WAY SLAB Introduction A slab is structural element whose thickness is small compared to its own length and width. Slabs are usually.

Chp.12 Cont. – Examples to design Footings

Section 3 design of post-tensioned components for flexure Developed by the pTI EDC-130 Education Committee lead author: trey Hamilton, University of.

Lecture #1 Student Objectives: * You should know what the instructor expects from you to final grade * You should be able to assess your level of knowledge.

2E4: SOLIDS & STRUCTURES Lecture 16 Dr. Bidisha Ghosh Notes: lids & Structures.

PCI 6th Edition Connection Design.

An-Najah National University Faculty of Engineering Civil Engineering Department Terra Santa School Structural Design and Analysis Prepared By: Bara Shawahna.

Structure Analysis I. Lecture 2 Types of Structures & Loads.

Chp-3-Strength Analysis of Beams According to ACI Code

CE 515 Railroad Engineering

Dr. Ali I. Tayeh First Semester

Senior Project 24’x24’ structure By: Andrew LeBlanc ET-494 Fall 2013-Spring 2014 Advising by: Rudolph Rode and Byron Patterson.

Fatigue in Concrete Structures Raquib Ahsan, Ph.D. Professor Department of Civil Engineering BUET.

Villanova University Dept. of Civil & Environmental Engineering CEE Capstone II Structural Engineering 1 CEE Capstone II Structural Engineering.

5 april 2004 J.M. Zwarthoed Workshop on Cracking and Durability of Reinforced Concrete Concerning the Serviceability Limit State.

Al-Najah National University Engineering Faculty Civil Engineering Department Graduation Project: Analysis & Design of Warehouses in Jaba’-Jenin.

Chapter 4 - Flexure. Lecture Goals Structures Basic Concepts Rectangular Beams.

LECTURE #1 Book Overview Read Chapt. 1(skip sect. 1.9)

Structural Analysis and Design of

Chapters Project title : Hirbawi Center A building lies in the east side of Tulkarm, this building consists of five stories of ( m 2 ) A building lies.

Prepared By: Mohammed wafiq omer Mahmoud hammad Abd Algani Sami Malath omair An-Najah National University Faculty of Engineering Civil Engineering Department.

Tulkarem Multipurpose Sport Hall Prepared by: Moatasem Ghanim Abdul-Rahman Alsaabneh Malek Salatneh Supervisor: Dr. Shaker Albitar.

Structural Design of Movenpick Hotel

◦ Ar-Rafedain building is 8 stories reinforced concrete building,located in Nablus city and used as commercial and residential building. ◦ The basement.

CTC 422 Design of Steel Structures

LRFD-Steel Design Dr. Ali Tayeh Second Semester

An-Najah National University Faculty of Engineering Civil Engineering Department.

CTC 422 Design of Steel Structures Introduction. Steel as a Building Material Advantages High strength / weight ratio Properties are homogeneous and predictable.

An-Najah National University Faculty of Engineering Civil Engineering Department Graduation Project Prepared by : 1- Areej Melhem 2- Jawad Ateyani 3-Rasha.

Steps in Foundation Engineering Understand project and site Develop design criteria Identify possible foundation alternatives Conduct soil investigation.

How Bridges Respond to Loads

Chapter 13 Concrete Form Design. SLAB FORM DESIGN Method WALL AND COLUMN FORM DESIGN DESIGN OF LATERAL BRACING.

Shear Stresses in Concrete Beams

PLAN Square Base Plate, A1, in2 Finding Size of Plate ( __in x __in) FINDING THICKNESS OF PLATE (__in) Square Concrete Pedestal, A2, in2 Basic Sizing of.

ENCE 710 Design of Steel Structures IV. COMPOSITE STEEL-CONCRET CONSTRUCTION C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University.

Practical Design of PT Buildings

Analysis and Design of Reinforced Concrete Beams

INTRODUCTION TO FORM DESIGN (CHAPTER ONE) WHAT KNOWLEDGE BASE SHOULD UNDERSTAND TO HANDLE FORM AND BRACING DESIGNS? STRENGTH OF MATERIALS STEEL DESIGN.

Structural Loads.

Bridges and Loads Modified by Matthew Silbernagel.

Objectives of Design of Reinforced Concrete Elements

Civil engineering department Foundation Design of Al – Jasser Building

Lecture 5 - Flexure June 11, 2003 CVEN 444.

An-Najah National University Faculty of Engineering

AQQABA SECONDRY SCHOOL Structural Design.

جامعة النجاح الوطنية كلية الهندسة قسم هندسة البناء

Chapter 3 – Mechanical Properties of Material

Reinforced Concrete Design

Supervied by : Eng. Ibrahim Mohammad Prepared by : Atheer Daraghmeh

Integrative Design of a Secondary School

Reinforced Concrete Design. Compressive Strength of Concrete f cr is the average cylinder strength f’ c compressive strength for design f’ c ~2500 psi.

Welcome to My Presentation

Analysis and Design of Multiple story building

Design of Beams - Limit States

Structure I Course Code: ARCH 208 Dr. Aeid A. Abdulrazeg

Structural Components

Structure I Course Code: ARCH 208 Dr. Aeid A. Abdulrazeg.

AN-NAJAH NATIONAL UNIVRESITY

Analysis And Design Of AS-Shorooq Residential Building

NOTATION fps = stress in prestressing steel at service loads less decompression stress, ksi 4/7/2019 Ce 572.

Graduation Project 2 3D Seismic Design of Omar Al-Alool School

Presentation transcript:

Design Process 1.Selection of the type of structural form to be used and the material out of which the structure is to be made. 2.Determination of the external loads that can be expected to act on the structure. 3.Calculation of the stresses and deformations that are produced in individual members of the structure by the external loads. 4.Determination of the size of the individual members so that the existing stresses and deformations are acceptable (i.e. satisfy the strength, fatigue, and serviceability limit states).

Design Methodologies and Loads Chapter 2S Already assigned Chapter 1S and 1C

Design Methodologies and Loads Design Codes Loads Load Combinations Allowable Stress Design Ultimate State Design Probabalistic-Based Design Limit States (Strength, Service)

Design Codes Steel - AISC, AASHTO, AREA Concrete – ACI 318, AASHTO Building – BOCA, UBC

Loads Types?

Dead Load Material Weights (lb/ft 3, lb/ft 2 )

Building Live Loads

Truck Live Loads

Load Combinations and Load Factors

Earthquake Loads Map