Unit 42: Heat Transfer and Combustion

Slides:



Advertisements
Similar presentations
Conduction Conceptests
Advertisements

Quiz – An organic liquid enters a in. ID horizontal steel tube, 3.5 ft long, at a rate of 5000 lb/hr. You are given that the specific.
Electrical Analogy of Heat Transfer P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Simple ideas to Eliminate Discontinuities.
Application of Steady-State Heat Transfer
ERT 216 HEAT & MASS TRANSFER Sem 2/
UNIT 13 : HEAT 13.1 Thermal Conductivity 13.2 Thermal Expansion.
Heat transfer rates through a bedroom window with and without an A/C unit Sam Sanderson David Theurer December 2006.
1 HEAT TRANSFER PROBLEMS PhysicsPhysics EnvironmentalEnvironmental Equipo docente: Alfonso Calera Belmonte Antonio J. Barbero Departamento de Física Aplicada.
Heat Transfer Chapter 2.
Heat energy transfer mechanisms oConduction oConvection oRadiation.
MECHANISM OF HEAT TRANSFER Mode of Heat transfer Conduction Convection
Extended Surfaces/Fins Convection: Heat transfer between a solid surface and a moving fluid is governed by the Newton’s cooling law: q = hA(T s -T  ).
Chapter 3 STEADY HEAT CONDUCTION
Chapter 2: Overall Heat Transfer Coefficient
Operational Principle of Thermal Bubble Jet injected droplet heater bubble Chamber neck liquid Current pulse heats up liquid Bubble as a pump pushes out.
Chapter 2: Steady-State One-Dimensional Heat Conduction
One Dimensional Steady State Heat Conduction
One-Dimensional Steady-State Conduction
Example 1:- An annular alloyed aluminum (k = 180 W/m . K ) fin of rectangular profile is attached to the outer surface of a circular tube having an outside.
CHE/ME 109 Heat Transfer in Electronics LECTURE 7 – EXAMPLES OF CONDUCTION MODELS.
One Dimensional Steady Heat Conduction problems P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Simple ideas for complex.
LINEAR SECOND ORDER ORDINARY DIFFERENTIAL EQUATIONS
PM3125: Lectures 6 to 9 Content of Lectures 6 to 12: Heat transfer:
Conduction & Convection.
Internal Flow Convection -constant surface temperature case Another commonly encountered internal convection condition is when the surface temperature.
CBE 150A – Transport Spring Semester 2014 Heat Transfer Introduction.
Lab-1,Week 1, EML 3016 C- Spring 2003 Electronic Device Cooling A thin (assume zero thickness) electronic chip has a square shape of an area 5x5 cm 2,
STEADY HEAT TRANSFER AND THERMAL RESISTANCE NETWORKS
PM3125: Lectures 10 to 12 Content of Lectures 10 to 12: Heat transfer:
ISAT Module III: Building Energy Efficiency
Overall Heat Transfer Coefficient
Chapter 3 Part 1 One-Dimensional, Steady-State Conduction.
1 ISAT Module III: Building Energy Efficiency Topic 7: Transient Heating and Air Conditioning Loads  Thermal Admittance  Intermittent Heating 
ERT 216 HEAT & MASS TRANSFER Sem 2/
One-Dimensional Steady-State Conduction
Pharos University جامعه فاروس Faculty of Engineering كلية الهندسة Petrochemical Department قسم البتروكيماويات PE 330 ENERGY CONSERVATION LECTURES (6-7)
JCOV, 25 OCT 2001Thermal screens in ATLAS Inner Detector J.Godlewski EP/ATI  ATLAS Inner Detector layout  Specifications for thermal screens  ANSYS.
Master’s of Engineering Project Fall 2010 Viram Pandya.
Convection: Internal Flow ( )
Heat Transfer Equations. Fouling Layers of dirt, particles, biological growth, etc. effect resistance to heat transfer We cannot predict fouling factors.
Unit 42: Heat Transfer and Combustion
Shape Factor Example 2 The shape factor can be modeled as a thermal resistance where Rt=1/kS. Therefore, it can be integrated into the electrical circuit.
Chapter 17 STEADY HEAT CONDUCTION
Unit 61: Engineering Thermodynamics Lesson 6: Heat.
Heat Transfer Introduction and Conduction. Conduction  If a temperature gradient exits in a continuous substance, heat can flow unaccompanied by any.
Shape Factor Example The shape factor can be modeled as thermal resistance as R t =1/kS, Therefore, it can be integrated with the electric circuit analog.
Heat Transfer Review. What type of heat transfer does this picture describe? Radiation.
Unit 42: Heat Transfer and Combustion Lesson 6: Conduction-Convection Systems.
Exercises for Q1. Insulated copper tube A thin walled 10 mm copper tube is used to transport a low-temperature refrigerant with a temperature that is.
STEADY HEAT CONDUCTION IN PLANE WALLS, Ch.3
TUTORIAL 1 7/3/2016.
1-D conduction through cylinders
HEAT TRANSFER Problems with FEM solution
Heat Transfer Su Yongkang School of Mechanical Engineering # 1 HEAT TRANSFER CHAPTER 8 Internal flow.
Lesson 7: Thermal and Mechanical Element Math Models in Control Systems ET 438a Automatic Control Systems Technology 1lesson7et438a.pptx.
HEAT TRASNFER IN BUILDINGS
The 3 Types of Heat Transfer
One-Dimensional Steady-State Conduction
14-6 Heat Transfer: Conduction
C.K. PITHAWALA COLLAGE OF ENGINEERING AND TECHNOLOGY
Building Energy Analysis
Unit II Conduction with & without Heat Generation.
Lesson 12 CONDUCTION HEAT TRANSFER
ET 438a Automatic Control Systems Technology
Conduction thermal resistance in different coordinate system
What is Fin? Fin is an extended surface, added onto a surface of a structure to enhance the rate of heat transfer from the structure. Example: The fins.
Example (3): Steam flowing through a long, thin-walled pipe maintains the pipe wall at Uniform temperature of 500 k. the pipe is covered with an insulation.
Steady-State Heat Transfer (Initial notes are designed by Dr
What are Fins ? Fins are extended surfaces used to increase the rate of heat transfer. It is made of highly conductive materials such as aluminum.
Presentation transcript:

Unit 42: Heat Transfer and Combustion Lesson 5: Lagging

Aim LO1: Understanding Heat Transfer Rates for Composite Systems.

Critical Thickness of Insulation Let’s consider a layer of insulation which might be installed around a circular pipe. If the pipe is metal then as has been shown the temperature on the inner surface of the pipe varies little to that of the outer surface and therefore for practical purposes it can be ignored ri h, T∞ ro T∞ Ti To Ln(ro/ri) 2πkL 1 2πkL

Critical Thickness of Insulation The inner temperature of the insulation is fixed at Ti and the outer surface is exposed to a convection environment at T∞. From the equivalent resistor network the heat transfer is… q = 2πL(Ti – T∞) Ln(ro/ri) + 1 k roh

Critical Thickness of Insulation In interesting consideration is the amount of insulation (lagging) required (i.e. radius ro) that will maximise the heat transfer… i.e. dq = 2πL(Ti – T∞)[(1/kro) – (1/hro2)] = 0 dro Ln(ro/ri) + 1 2 k roh Thus at a maximum ro = k/h ro being referred to as the critical radius

Critical Thickness of Insulation q This shows that lagging (insulation) when placed onto the outer surface of a pipe will increase the heat flow if it is less that the critical radius ro. Greater that ro, the heat flow will decrease. ro r

Critical Thickness of Insulation Thus if the outer radius is less than the value given by ro = k/h, then the heat transfer will be increased by adding further insulation. For radii greater than the critical value an increase insulation thickness will cause a decrease in heat transfer. The central concept is that for sufficiently small of h the convection heat loss may actually increase with the addition of insulation because of the increased surface area.

Critical Thickness of Insulation Calculate the critical radius of insulation for asbestos (k=0.17 W/m.oC) surrounding a pipe and exposed to room air at 20oC with h = 3.0 W/m2.oC. Calculate the heat loss from a 200oC, 5.0 cm diameter pipe when covered with the critical radius of insulation and without insulation.

Critical Thickness of Insulation ro = k/h = 0.17/3.0 = 0.0567 m = 5.67 cm q = 2π(200 – 20) = 105.7 W/m L Ln(5.66/2.5) + 1 0.17 (0.0567)(3.0) Without insulation the convection from the outer surface of the pipe is… q = h(2πr)(Ti – To) = 3 x 2π x 0.025 x (200 -20) = 84.8 W/m L

Critical Thickness of Insulation So the addition of 3.17 cm (5.67 – 2.5) of insulation actually increases the heat transfer by 25%. As an alternative, fibreglass having a thermal conductivity of 0.04 W/m.oC might be employed as the insulation material. Then the critical radius would be… ro = k/h = 0.04/3.0 = 0.0133 = 1.33 cm

Critical Thickness of Insulation Now the critical radius is less than the outside radius of the pipe (2.5 cm) so addition of any fibreglass insulation would cause a decrease in the heat transfer. In a practical pipe insulation problem, the total heat loss will also be influenced by radiation as well as convection from the outer surface of the insulation.