Technician Hand Tools By:Dillan Hyatt. FT812 Toolkit A variety of tools used to help complete a task.

Slides:



Advertisements
Similar presentations
From : Michel MATHIEU to : Luis HERVAS CABLING sub-D 37 M for trigger cables 1- strip the cable cutting off the external gaine on a length of about 7cm.
Advertisements

Building a Weather Station for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Computer Technician Technicians Tools Copyright © Texas Education Agency, All rights reserved.1.
How to wire Ethernet Cables. Tools Required CAT 5 Cable - bulk Category 5, cable RJ45 Ends Crimper for RJ45 Wire Cutters - to cut and strip the cable.
How to Make a Straight-through Cable
How to install a PL-259 My Way! by Steve, N1NXU. Start with a clean cut. Notice how the top cable end is a nice clean round cut. It was cut with a cable.
New Mexico FFA Agricultural Mechanics Career Development Event Electric Power.
IT Club Workbench BY Chris Sorensen Mike Hockenberry Brendon Andrews.
Training Meeting: ‘Handy Man 101’ October 21, :00pm CE 110.
Jon linthicum Classwork: FT812 Toolkit Contains various types of tools. To tackle any electronic build.
Computer Tools and kits for Computer troubleshooting
Electrical Wiring Circuit Board Project. STEP 1 - Identify all Parts of the Project Saw Drill Driver w/ bits Drill w/bits (not pictured) #2 Phillips Screwdriver.
Hand tools. Standard Head Screw Driver Used to tighten or loosen flat head screws.
Tool Use Strip wire. Soldering Iron Step 1: Tinning the iron Tinning helps to make soldering easier and quicker while keeping the iron in good condition.
How to Install A Pop-n-Lock system on F-150 SVT Raptor By: Jacques DuBois.
Wiring MVRT 2010 – 2011 Season. Table of Contents Wire stripping Crimping Soldering.
Bob Howard 10/22/2011.  How many connectors do you need ◦ Max DC/Servo Motor Controllers is 4 so use 4  How long should the connectors be ◦
A Basic Toolkit 3-prong retriever Nut driver Phillips screwdriver Storage container Tweezers Torx driver Flat head screwdriver Chip extractor.
Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.
Electrician’s Tools Of The Trade
Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.
Crafting a Cat5e Cable Scott H. Bowers. Materials Raw Cat5e cable ~50 feet. Wire Cutter/Cable Stripper RJ-45 Crimper Ethernet tester RJ-45 terminators.
How to Build an Ethernet Cable ASIF ISLAM LTEC 4550 University of North Texas.
Electrical Wiring. Wire Size Comparison MEl ec- Ch #16 top to #10 bottom #2 top to #10 bottom.
Tools.
Wire and spinning magnets Reference: Original Authur: William Beaty 1996.
Two Categories of Troubleshooting tools Hardware Tools Software Tools.
Verigy V93000 Service Training
Hand Tools By: Kyle Powley. Torx Driver Set This is a driver set that are like hex keys.
Ethernet Cable. Straight Through Connection  I went ahead with the Straight through connect for my first few cables, using the T-568A wiring standard.
Hand Tools By Tynedra Murphy. Torx Driver Set Set of screwdrivers varying in sizes.
PC Systems Building System Components Installation Procedures Sample PowerPoint Presentation.
Metalwork. Information about Metalwork Quick Facts Metalwork is a Three Year Course. It ends with the Junior Certificate Exam in 3rd Yr. There is a Higher.
Network Anatomy By: Roland J. Boutte. Ethernet Cable cable used to connect computing devices together directly. two hosts or two switches to each other.
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 34 Installing Branch Circuits.
PREPARATIONS TOOLS ： 1 、 wire stripper 2 、 coating stripper 3 、 fiber length measurement 4 、 cutter QUICK ASSEMBLY CONNECTOR 1.
Tools you will need #8 Torx driver #10 Torx driver Standard Phillips screwdriver Small (jewelers)Phillips screwdriver Small standard screwdriver.
How to Create RJ – 45 Wire.   To create the RJ – 45 cable or better known as the Cat wire it is very simple all you need to do is follow my simple instructions.
Lighting and Wiring Service Chapter 37 Page 477. Four Types of Electrical Problems Open Circuit- when a circuit has a break in continuity. Open Circuit-
Safety, Tools and Equipment, Shop Practices Tools and Equipment.
Tools used in this demonstration include: Flathead Screwdriver Wire Cutters.
Oisture Tester How to Solder. Learning Objectives Understand the soldering process Practice soldering Continue with design ideas Produce an information.
Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.
David Rodriguez.  Use protective glasses  Be careful of sharp tools  Have first aid-kit near by  Familiarize yourself with surroundings.
T. Hajer Brahim & T. Rania Alakazalah U.Y: 1435/1436 H.
© ExplorNet’s Centers for Quality Teaching and Learning 1 Use appropriate tools for network cabling and connections. Objective – 2%
ELECTRICAL TOOLS and ITS FUNCTION
How to wire Ethernet Cables. Tools Required CAT 5 Cable - bulk Category 5, cable RJ45 Ends Crimper for RJ45 Wire Cutters - to cut and strip the cable.
ETHERNET CABLE TYLER THORNBURG LTEC STRIPPING AND CUTTING First you will need to strip the wire. I used scissors to cut off the rubber around.
Constructing/Testing 4-Pair Cabling Systems
Used for cutting wood and plastic
Automotive Engines Theory and Servicing
PostBase Automatic Feeder Component Removal Service Training
AO Series 10 Illuminator pattern
How to wire Ethernet Cables
Introduction to Soldering (PCB Bread boards)
Soldering Leads to the DC Motor
Electrical Wiring Circuit Board Project
Research 5 different electronic toys
Fiber optics (LAMDA-P)
Health & Safety Education
Computer Technician Technicians’ Tools Trade & Industrial Education
Basic Hand Tools When making working models in the Imagineering Clubs, you will be using a variety of Hand Tools. For example making the Steady Hand Game.
Controller Rework.
Required tools for installation of a V-1020C Speaker with V-9914M-5 Metal Bridge.
Power Tools: Power Drilling Tools
Soldering: Methods, Tips, and Applications
Electrical components and systems
Welding Tools.
Automotive Technology Principles, Diagnosis, and Service
Presentation transcript:

Technician Hand Tools By:Dillan Hyatt

FT812 Toolkit A variety of tools used to help complete a task.

Torx Driver set with T9 Used to insert and remove torx screws.

Power Screw Driver Used to take the man power out of the work.

Small flash light Illuminates small places so that one can see better.

Ether net cable tester Should be pretty self explanatory. It tests to see if the ether net cable is working.

Networlk/phone crimper Used to cut, strip, and twists wires

Multi Tool Handy so that you have your most basic tools in one device.

Solder Sucker Sucks that’s unwanted molten metal out of the places you don’t want it

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.