1 Body Electrical - Lighting Lighting - Meter Meter - Air Conditioner Air Conditioner - Toyota Parking Assist Toyota Parking Assist - Power Window Power Window - Wireless Door Lock Control Wireless Door Lock Control - Engine Immobiliser Engine Immobiliser - Theft Deterrent System Theft Deterrent System - SRS Airbag SRS Airbag

2 Body Electrical Lighting Head Lamp projector for Low Beam High Beam Low Beam (with projector) Turn Signal Reference construction

3 Body Electrical Lighting Front fog lamp, side turn signal & rear combination lamp Combination Lamp Front Fog Lamp Side Turn Signal

4 Body Electrical Service Points Replacing side turn signal bulb Outer rear view mirror and Outer mirror cover must be removed to replace the turn signal bulb.

5 Body Electrical Lighting High Mount Stop Lamp, LED type (S grade) & Bulb type (G grade) 1.5 S 1.5 G

6 Body Electrical Meter Analog type combination meter

7 Body Electrical Meter LCD Fuel meter The low fuel level warning light blinks when fuel is less than 6.8L in the tank. (Tank capacity is 45L)

8 Body Electrical Air Conditioner Manual Air Conditioner Double Blower Rear blower (A/C) will operate if ONLY front A/C is operated

9 Body Electrical TOYOTA Parking Assist Standard equipment in all models ”A” distance (mm) IndicatorBuzzer Approx ( )BlinksIntermittent Approx ( ) Fast BlinksFast Intermittent Approx 800 (31.5) or lessLitContinuous Sensors Click Movie

10 Body Electrical Power Window Standard equipment in all models One touch auto-up/down for driver’s door Window Lock Notes: WITHOUT Jam Protection function

11 Body Electrical Wireless Door Lock Standard equipment in all models Lock - Unlock ! Unlock Lock

12 Body Electrical Service Points Wireless Code Registration Procedure * Up to 4 transmitters can be registered. (part no BZ050) 1.Prepare all transmitters to be registered 2.Confirm no key in the ignition key cylinder 3.Disconnect the battery negative terminal or door control receiver connector 4.Reconnect the battery negative terminal or door control receiver connector 5.Within 15 seconds, close all doors and press the unlock switch of 1 st transmitter for 5 seconds or more 6.Confirm that the door control receiver automatically performs the lock- unlock operation once 7.Within 5 seconds, press the lock switch for 1 seconds or more 8.Confirm that the door control receiver automatically performs the lock- unlock operation once 9.Repeat step 5 (excludes closing all doors) to step 8 to register other transmitters 10.Wait for 15 seconds or more after registration of all transmitters

13 Body Electrical Engine Immobiliser System Disables the engine from starting using the ignition key without an ID code that matches the pre-registered code in the vehicle Standard equipment for all models Transponder Chip Transponder Key Coil ID Code Transponder Key ECU Matching Click Movie!

14 Body Electrical Engine Immobiliser System System Diagram

15 Body Electrical Theft Deterrent System Standard equipment in all models TDS system is equipped in TAM (Port Installation Option) System Indicator (w/ Immob System)

16 Body Electrical Theft Deterrent System Maximum of 4 transmitter can be registered Transmitter for this system is different from Door Lock Transmitter (factory original) Lock Button Un-Lock Button Panic Button Indicator 1.2 transmitter are provided (total 3 pcs, including factory original) 2.Can be used for LOCKING/UNLOCKING Factory Original Spare Tire Cover Key

17 Body Electrical Theft Deterrent System System operation

18 Body Electrical Registration (Alarm Transmitter) 1.Prepare transmitter to be registered 2.Driver’s door: start from open condition, close and open door once in less than 5 seconds. 3.Insert IGN key, turn to ON then ACC for 5 times (last position is ACC), then after 1.5 second, horn will sounds once. 4.Press transmitter button: a)LOCK 5 times* for the 1 st transmitter, while pressing the button, horn will sound once, to indicate that registration memory has been added. b)LOCK 1 time for 2 nd transmitter, while pressing the button, horn will sound once, to indicate that registration memory has been added. 5.Programming will be completed if: a)10 seconds has elapsed (no activities) b)IGN Switch is turn to ON position c)Close and open any of the door (s) 6.Horn will sound once (short) then another once (long), to indicate that the programming has been completed *: If the transmitter is lost, while no replacement at the moment, by only doing step (a) will automatically erasing registered transmitter from ECU

19 Body Electrical SRS Airbag Standard equipment for 1.5 S A/T model Electronic type Airbag for Driver and front passenger

20