PICTURE BASED PRESENTATION. Prepared By : Mazadul Hasan sheshir ID: 2010000400008 13 th Batch (Session : 2009 - 2013) Department : Wet Processing Technology.

Slides:



Advertisements
Similar presentations
ACTIVE LEARNING PROCESS
Advertisements

Heating, Ventilation, and Air-Conditioning (HVAC) Systems
The Millitron. Built in Speed: 2 – 20 m/min 2.Capacity: 200,000 m 2 per week 3.Colours: 12 + endless mixes 4.Length of unit: 120 m Facts about.
Welcome.
Factor of Evaporation: lbs/hr steam produced per BHp.
Engine Cooling And Lubrication
The Production Process for Weyerhaeuser Containerboard and Corrugated Packaging Producing Satisfaction from Renewable Resources slidelib\cbp\process (1)
Heating, Ventilating, and Air-Conditioning
Lecture 13 Single Knit Machines (plain).
HVAC Heating, Ventilation and Air Conditioning -something that you never think about until it doesn’t work properly.
Introduction Enthalpy Wheel
Laundry. Supplies Detergent or Soap Stain Remover Fabric Softener Bleach Thread, Needles, Buttons.
Mini Jet Sample Dyeing M/C Daelim Starlet Co., Ltd.
THERMAL POWER PLANT.
2.02 Explain ways to care for apparel. Sorting clothes  Weight- Sturdy cotton, Knits, & Delicate  Color- White, Light color, & Darks  Heavily Soiled-
CUTTING ROOM… A STUDY FOR PROBLEM IDENTIFICATION AND SOLUTION.
PRE-PRINT TECHNOLOGY LTD. Pre-Print Technology Linerflex.
Drying Processing Presentation
Pump Affinity Laws. P. 100 of text – section 4: vary only speed of pump P. 100 of text – section 5: vary only diameter P. 106 of text – vary BOTH speed.
Reflow System to Electronics Assembly
Coal Burning System.
HVACR416 - Design Humidification. Relative Humidity 1.Air in the home is artificially dried out when it is heated. 2.Because warm air expands, this expansion.
Canola Harvesting BY Derek Thoms. What can be used to harvest canola This is a grain head which is used to harvest small grain products like canola. This.
With over 60 years experience Mondial Forni ensures the highest baking quality and maximum reliability in their ovens. The Ciclomondial combustion gas.
Objectives Finish with Multizone Systems
We turn the AIR into a TOOL MOTOR BLOWER BASEPLATE Commonly used Nantong motor Imported from France Made in Taicang factory.
3. Cooling a. Introduction 1) Definition reduce temperature of air entering greenhouse Why? –Reduce stress –Uniformity –Better growth.
Field Lab Sample Processing Sequence. 1)Tare a bag on the balance 2)Weigh the field moist sample, in the bag, record weight. Weigh to at least one decimal.
Steam Power Station Presented By Ashvin G. Patel Asst. Prof. (E.E.)
HEAT PIPE HEAT EXCHANGERS
CHAPTER 6 Moving Heat: Heating and Air Conditioning Principles
Gas Turbine Power Plant
RO400FC Forced convection hot air reflow oven. In a flexible production, what do you need for soldering of  Complex PCB’s  Soldering of fine pitch on.
DRYING Dr. Basavaraj K. Nanjwade M. Pharm., Ph. D
DESIGN AND PERFORMANCE EVALUATION OF AN EVAPORATIVE HEAT EXCHANGER A.O. MURITALA, S.O. OBAYOPO, S.K. FASHOGBON, O.T. POPOOLA*, S.A ADIO Department of Mechanical.
 Spray drying - formation of droplets from the bulk liquid – moisture removal  liquid droplets - sprayed –drying chamber  the low-humidity hot gas.
Refrigeration and Cooling Principles for Potato Storages Roger Brook Professor and Extension Engineer Agricultural Engineering Department Michigan State.
Production of Forward RPC Gaps CMS Forward RPC EDR (10/10/2002 – 11/10/2002) Seong Jong Hong KODEL, Korea University.
1 Combustion Efficiency Test. 2 Principles 1.Composition of flue gases 2.Flue gas smoke concentration 3.Temp of flue gas 4.Draft produced 5.Excess combustion.
Automotive Heating and Air Conditioning CHAPTER Automotive Heating and Air Conditioning, 7e James D. Halderman | Tom Birch SEVENTH EDITION Copyright ©
Exercise 14 - Pg 203 Atmosphere and Moisture. 3 Forms of Water Three forms or phases - solid liquid, and gas. It is still water; just in different phases.
Automotive Heating and Air Conditioning CHAPTER Automotive Heating and Air Conditioning, 7e James D. Halderman | Tom Birch SEVENTH EDITION Copyright ©
Biscuit baking process and engineering
EVAPORATION EVAPORATION By: Dr. Tahseen Ismail By: Dr. Tahseen Ismail.
SCHOOL OF RENEWABLE ENERGY (SCORE) MAEJO UNIVERSITY CHIANG MAI, THAILAND Methods Objectives Performance Analysis of Mulberry Paper Handmade Dryer by Using.
Prepared By : Mazadul Hasan sheshir ID: th Batch (session ) Department : Wet Processing Technology
Woven Dyeing Machinery
Winch Dyeing machine.
Knit Dyeing Machines.
Air condition installation
E3 HVACR Controls and Devices
Automotive Engines Theory and Servicing
Automotive Heating And Air Conditioning
Maria’s Restaurant Chapter 2 Section 9
Energy Management and Planning MSJ0210
-Wet processes. -Flow chart of material flow within a wet processing mill. -The major processes involved in wet processing Faiza Anwar.
Combined Hot-Smoking & Cooking Installation
ARAC/H/F Air-cooled water chillers, free-cooling chillers and heat pumps Range: kW.
Automotive Heating And Air Conditioning
E3 HVACR Controls and Devices
SEMINAR ON AIR CIRCULATION IN STENTERS
Thermoforming Process
Other Mechanical finishing Treatments
Humidity Control Applications Flakt Dryers
Air Conditioning System-1
Management of Quality in Finishing Part 2: Practical Considerations
Maria’s Restaurant Chapter 2 Section 9
For Textile Processing Machines nnovative engineering.
Presentation transcript:

PICTURE BASED PRESENTATION

Prepared By : Mazadul Hasan sheshir ID: th Batch (Session : ) Department : Wet Processing Technology ( Blog : Southeast University Department Of Textile Engineering I/A 251,252 Tejgaon Dhaka Banglade sh Prepared By :

Drying is defined as a process where the liquid portion of the solution is evaporated from the fabric. In Relax dryer machine in BKL containing 2 Gas burner, 2 Chamber, 8 Blower and 2 Conveyer net.

Dryer machine is used for removing the residual water contained in the fabric after squeezing by applying heat on the fabric. In this machine the fabric is fed on the drying net at low over feed speed and the humidity is continuously measured. Drying is done by applying heat through burner nozzles. During drying the total heat passed through the machine is extracted by the exhaust fan

To dry the fabric with the help of blower and burner. To control the shrinkage of the fabric. To prepare the fabric for next subsequent process. To dry fabric without tension. To remove residual water containing in the fabric.

Measuring tape. Die-cutter. Electronic Balance. Expander. Scissors. Trolley.

To clean the machine properly. To clean the trey for every chamber. To check the proper activity of burner. To check over feeding and vibrating. To check the conveyor belt.

After dewatering then the fabric through the dryer. the main function of the dryer is given below: -To dry he fabric -To control the overfeed system. -To control vibration which increase the GSM. The m/c contain two chambers. two mesh endless conveyors are placed lengthwise to the chamber named conveyor net and filter net. each chamber contain aburner, which supply hot air. This hot is guided through he ducting lin by suctionfan. there are a nozzel placed in btnfilter and conveyor net. when fabric pass through on the conveyor net, hot air is supplied to the wet to dry it. there are exhaust fan which such he wet air and deliver to tea to through the ducting line. The speed of dryer depends on the temp. ofhe m/c & GM of the fabric. If the m/c temp.is high& m/c speed also high and the m/ c temp. is low then mc speed also low. The vibration speed of the m/c for heavy fabric is 730m/min and normal fabric is 480m/min. Working principle of dryer:

Machine ParameterSet Up Value Temperature Setting( ) for white shade, ( ) for light shade, ( ) for dark shade, ( ) for curing. Blower Fan SettingAuto Exhaust Fan SettingAuto Machine Speed3-35 m/min (depends on quality). Over Feed0-40% (depends on construction). Width of Expander Setting cm (depends on the required width of fabrics). Burner Gas Pressure10-15 M/Bar.

Fabric TypeOverfeed % Temperature 0 CSpeed (m/min)Folder Speed (m/min) Vibration ColorWhite Color High G.S.M Low G.S.M Single Jersey30 % to-40% C C ~3As Required Single Lacoste 30 % to-35% C C ~3 As Required Polo Pique30 % to-40% C C ~3As Required Interlock30 % to-40% C C ~3 As Required Grey Mélange 30%-40% C C ~4As Required For cotton fabric:

Fabric TypeTemp. ( o C) Over feed (%) Vibration Ext. Temp. ( o C) Speed S/JWhite Color PKWhite Color X1 RibTube Open P. Interlock Mercerized Grey Fabric X1 L. Rib

Dryer- (multifunctional) Band name:- Santex Origin: – China M/C Type- Santashrink progress. Year of construction Chamber: -4 Com.no: 6960/2600(mm) Elect-Voltage: 3×400/50(Volt/Hz) Connected Load: 193/435(KW/A)

Schematic Diagram of a Dryer Machine

Input Fabrics In to the Dryer

1.To dry the fabric. 2.To control the hand Feel 3.To control the Twist 4.To control the shrinkage + Dia + Gsm

1.Drying Net. 2.Heating Chamber: 3.Blower. 4.Burner. 5.Free Roller. 6.Centering Roller. 7.Scroll Roller. 8.Folder. 9.Rubber Belt for fabric delivery. 10.Exhaust fan.

1.Overfeed. 2.Temperature. 3.Padder pressure. 4.Speed.  Heating chamber: 4  No of burner: 4

1.Shade check 2.Width check 3.Fabric faults (color spot, uneven, hole, Dia,mark, ec).

Checking parameters: 1.Overfeed ( %) : It depends on fabric structure & GSM 2.Temperature: It depends on color & GSM.( normally for single jersey -1600C, for high GSM, like-fleece, it may be 2500C ) 3.Speed: It depends on fabric GSM. For higher GSM, lower the speed. GSMOver feed Up to % % % %

Temperature:-Set the temperature between c c for white and c c for color fabric. If GSM increase than the temperature is increase Or, if moisture content increase than temperature is also increase.  Set the over feed up to 25~50% or as required to get finish G.S.M.  Set the speed as much as possible (6~20m/min). GSM speed

 If fabric is more Redder than the standard one, then reduce the temperature.  If fabric is more Yellower than the standard one, then increase the temperature.  If fabric is more Bluer than the standard one, then increase the temperature. N.B:

In Stenter and Dryer machines air is recirculated which passes from the exhaust sluts and air controller flaps. Then the air is passed over the nozzles through which fabric is passed and routes it over to the heat exchanger which lets the air to be heated by the burner. The circulating air fan allows the hot air to pass uniformly through the nozzles to the fabric where the air controller flaps control the upper and lower nozzle air and thus the fabric is heated. Finally the used hot air is passed on to the exhaust air duct.

Monforts Dryer (Dynair 5000):

No. of Chamber: 4 No. of Burner: 4 No. of Padder: 1 No. of Expander Roller: 5 (Motor Controlled) No. of Free Roller: 13 (Easy Controlled) No. of Blower: 4 No. of Finger Roller: 4 Capacity: 6 tons/day Maximum Temperature: 180oC Minimum Temperature: 100oC Fabric Passing Speed: 8 m/min to 50 m/min (Depends on fabric type, temperature & dry requirement i.e. half dry/full dry) Maximum Over feed (%): 60% Minimum Over feed (%): -10% Maximum Fabric Dia Capacity: 260 cm Minimum Fabric Dia Capacity: 85 cm

Machine should be cleaned Padder should be cleaned Stenter pin should be checked Tray of each chamber should be cleaned Function of auto chamber should be checked Padder pressure should be adjusted Function of burner should be checked Overfeeding speed should be checked Conveyor belt should be checked Dancing roller should be checked. Standard Operating Procedure:

Work Instruction:

Find out the limitations and faults of the machine and advise for removing these. Selvedge drying system is not properly functioning. Maximum over feed of the machine is +60%. When the steam temperature is 1000C-1200C, then delivered fabric temperature is C. But there is no cooling zone in this machine to reduce the excess temperature. So a cooling zone in delivery zone can be attached.

Mordan Shrink recovery Dryer

1. Yarn Manufacturing Technology Link: 2. Fabric Manufacturing Technology Link: 3. Garments Manufacturing Technology Link: 3. Wet processing Technology Link: 4. Fashion-Design-and-Technology Link: Technology/ ?ref=ts&fref=ts My Facebook Textile related Pages