SYSTEMS

Pumps Systems Our systems are identified as follows Example: model D-CPS-HT-1000-VFD Dis for Duplex units CPSis for Constant Pressure System HTis Hydro-Pneumatic Tank (optional) 1000is for pump series VFDis variable frequency drive (optional) All Systems will have the similar example series and model

Condensate unit systems, Series CVC Units consist of the following Simplex S-CVC or Duplex D-CVC Series GV6 or series 1000 pump (s) 15, 25,35,45 70 or 120 gallons Cast receivers Gauge glass and stop-cocks Float switch Dial Thermometer Control panel with electric alternator Voltages available 115/220/460/575 Factory Mounted & Pre-wired & Tested Optional Stainless steel Receiver Optional Steel Receivers Optional ASME code Optional Larger Receiver

Boiler feed Units Series BFC Units consist of the following Simplex S-BFCE or Duplex D-BFCE Series EVMU or series 1000 pump (s) Steel receivers 50, 70, 120, 210, 300, 500, 750, 1000, 1500, and 2000 gallons Gauge glass and stop-cocks Ball valve (s) and Strainer (s) Mc Donnell Miller no 21 feed water Stem or Dial Thermometer Voltage available 115/220/460/575 Factory Mounted & Pre-wired & Tested Optional Stainless steel Receiver Optional ASME code Optional Larger Receiver Optional Control panel with electric alternator Optional Steam injector

Fuel Transfer Systems, Series FOM Units consist of the following Simplex S-FOM or Duplex D-FOM Series CYB rotary vane positive displacement pump (s) Basket Strainer “P” or “Y” strainer (s) Gauge glass and stop-cocks Ball and check valves Liquid filled pressure gauges Separate Relief valve (s) Control panel with electric alternator Factory Mounted & Pre-wired & Tested Steel fabricated base plate Voltages available 115/220/460/575 Optional other type of pumps

Glycol Fill Systems, Series GLY Units consist of the following Simplex S-GLY or Duplex D-GLY Series CYB rotary vane positive displacement pump (s) Low level shut off float Hose filling valve (HN050) Ball and check valves Liquid filled pressure gauge Relief valve (s) Surge absorber Control panel & pressure switch Factory Mounted & Pre-wired & Tested Polyethylene fabricated base plate Polyethylene 53 gal tank with cover Voltages available 115/220/460/575 Optional 25, 106 or 200 gallon tank Optional Triplex or Quadruple units

Heating and Cooling Systems, (HC) Units consist of the following Simplex S-HC or Duplex D-HC Series 880RI pump (s) Pumps mounted vertically Ball, Butterfly and check valve (s) Multi-Function Valve (shown) Liquid filled pressure gauges P1 usually runs continuously Suction & Discharge Stainless Steel or steel Headers Control panel with pressure switch (es) Factory Mounted & Pre-wired & Tested Steel fabricated base late Voltage available 115/220/460/575 Optional Triplex or Quadruple Units Optional Pressure reducing and check valve (s)

Duplex Primary / Secondary Boiler Pack Duplex Control Panel PRIMARY LOOPSECONDARY LOOP

Duplex Pump / Single Boiler Primary Secondary Boiler Pack (DS-PSB-HT)

The DS-PSB-HT unit installed on the roof top

Duplex 880 VFD Heating pack VARIABLE FREQUENCY DRIVES Chemical Pot Feeder Glycol Fill

Duplex Pump / Duplex Boiler Primary Secondary Boiler Pack (DD-PSB-HT) Chemical Pot Feeder Expansion Tank Primary Loop Secondary Loop

Simplex Heat Transfer pack Shell & Tube Heat Exchanger Expansion Tank Series 2000 Pump

Simplex Heat Transfer pack Plate Heat Exchanger Expansion Tank Series 2000 Pump Suction Diffuser Multifunction Valve

Duplex Heat Transfer Module Shell Tube Heat Exchanger Glycol Fill Two Expansion Tank Plate Heat Exchanger

Duplex Heat Transfer Module

Bill of Material

Duplex Cooling pack (D-HC)

Duplex Pump / Single Boiler Primary Secondary Boiler Pack (DS-PSB-HT)

Duplex Primary / Secondary Boiler Pack Circulating Pump Chemical Pot Feeder Air Release Valve Expansion Tank Pump Series 1000 Boilers Flow-Switch Low-Water Cut-Off Pressure Relief Valve Air Separator Primary / Secondary Loop

Duplex Primary / Secondary Boiler Pack

Bill of Material

Series PSB Primary/Secondary Hydronic Boiler Systems Flo Fab packaged systems are designed to reduce time, cost and problems associated with the installation and start-up of a Hydronic heating system. Our pre-engineered system gives you total confidence that Flo Fab will provide you with top quality components that meet your system requirements. If your system requirement does not fit one of our pre-engineered packages, our expertise allows us to design and manufacture the right one for your application. Our philosophy is to provide superior products with outstanding customer service.

Series PSB Primary/Secondary Hydronic Boiler Systems Benefit for Contractors Compact footprint than otherwise with all components installed separately. Speeds start-up on Hydronic heating system. Easier project management; time savings, less chance of misplacing components until actual installation. Fixed cost, not variable cost as with field installed components. Our systems are pre-tested, assuring all components function properly together. Complete custom support from a single source.

Series PSB Primary/Secondary Hydronic Boiler Systems Benefit for Engineers and Owners One selection, one time. Guaranteed system performance. Complex system design brought down to simple component arrangement. All components assured to work together. Equipment manufactured to ASME / ANSI standards. NEMA rated control panels. Pre-engineered packages for selection. Custom configuration possible to accommodate existing systems. Complete custom support from a single source.

Series PSB Primary/Secondary Hydronic Boiler Systems Stand-by pump. Pressure and temperature gauges. Auto stand-by pumps starts on lead pump failure. Automatic pump alternation. Isolation valves to facilitate changing or maintenance of components. Balancing valves to maintain system equilibrium. Expansion tank. Air separator. Chemical pot feeder. Suction diffusers. Boiler protection: flow switch cut-off, low water cut-off, and pressure relief valve. System drain valves and air vents. Electrical control panel. Glycol filled package system. Prepiped and pretested skid mounted system. System Standards

Series PSB Primary/Secondary Hydronic Boiler Systems Indoor or Outdoor Installation. Fuel supply: natural gas or propane. Boiler by-pass to maintain minimum inlet temperature. Some system packages maybe broken down to be able to fit through conventional door sizes. System Options

Duplex Boiler Domestic Hot Water Pack (D-DHW)

880RI Cooling Tower Pack With Plate Heat Exchanger

THANK YOU VERY MUCH FOR YOUR ATTENDENCE