IOT POLY ENGINEERING I1-3 1. Using your handout of the design process steps place check next the items asked for as they appear on the screen. These are.

Slides:

Advertisements

Similar presentations

I Spy Engineering - Step 1 Groups of Two Notepad 2 Minutes List Everything You Can See that was Designed or Created by an Engineer Most Items Wins the.

Advertisements

7 TH GRADE STEM AGENDA Week 12 11/12 – 11/15. 7 TH GRADE AGENDA 11/12  Learning Target: I can use the design process to create a piece of furniture.

Design Process Overview. What is Design? Design is a process that is used to systematically solve problems.

1.Use the following information to determine the force required to lift the load using a 1 st class lever. 2.What would DF have to be to make the applied.

IOT POLY ENGINEERING I1-4 September 2, 2010 Drill Exercise With 1 partner: 1.Get out last night’s homework and critique the paper layout for correct formatting.

Somerset Berkley Regional High School Robotics Engineering with LabView.

Problem Solving Unit 2. Problem Solving 1. Define the problem – What is the problem? 2. Generate possible solutions – What are some things I can do to.

By Mr. Gary.  Keeping notes during class is a task that you have come to expect.  A record of your work helps you to explain to others what you were.

Bell Ringer Activity Signed safety wavers can go on my desk. Summative supply check next class (14 points). Singed Safety Waver Binder 50 Sheets of Notebook.

What Is Design? What Is a Design Process? Design Process Examples The Design Process © 2012 Project Lead The Way, Inc.

Instant Design Challenge

Instant Design Challenge

Instant Design Challenge Using the Design Process and Engineering Notebook.

Engineering Design Process

August 29, 2008 With 1 partner: 1.Get out last night’s homework and critique the paper layout for correct formatting. 2.Go through your assignments and.

Mousetrap Car Physics Concepts U3b-L9 If you are trying to build a long distance traveling or fast vehicle you will need to think carefully about the following.

Mousetrap Car Physics Concepts U3b-L8 If you are trying to build a long distance traveling or fast vehicle you will need to think carefully about the following.

Student Portfolio Development. Portfolio Development Define the following: Portfolio Artifact Evidence Medium Annotation Design Analysis STUDENTS: Write.

November 30, 2010 DESIGN PROCESS

January 31, 2011 Answer in a complete sentence from your notes.

Bell Ringer Complete the Introduction to Technology Worksheet 1. Please finish answering the questions on the introduction worksheet. If you finish early.

Engineering Design Purpose of the Lesson: To have students demonstrate the steps and processes involved in engineering design. Warm-up – Copy and complete.

Technology & Engineering

A Design Process O’Keefe - LBHS. What Is Design? What Is a Design Process? Design Process Examples Design Process Used in IED The Design Process.

Food Preservation Challenge The Science Behind Food Preservation Unit.

Engineering Design Process. Engineering Design Process.

IOT POLY ENGINEERING I1-1 October 7, In reference to robotics history, what happened during 1961? 2.What is an articulated robot? A robot with at.

1.Before you can solve any problem, what are two things you must know? 2. During the research and brainstorm step of the design process, how can the creativity.

RHS Tech Ed The Engineering Design Process. What Is Design?

September 3, 2010 With 1 partner: 1.Get out weekend’s homework and critique the paper layout for correct formatting. 2.Go through your assignments and.

Applying the Design Process Unit 3 Objectives: Evaluate a product in relation to the goal of design and potential improvement. Design an improvement of.

ENGR-TS-2: The students will develop an understanding of how the design process is used to develop a technological system. a. Identify the steps of the.

© 2011 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™ Foundations of Technology, Third Edition.

Engineering Design Process Applied Technology Engineering Design Process © 2011 International Technology and Engineering Educators Association, STEM 

1.The person sitting next to you is your Mechanical Basketball Shooter partner. 2.Get out your notebooks January 5, 2010 DRILL U3d-L10.

Technological Design Process Mr. Geesey. At the end of this presentation you should be able to…  Describe the steps of the Design Process  Apply the.

Concepts of Engineering Module 2 Test Review. Review Questions Design problems are broken down into sub- problems because smaller problems must be solved.

Using the Engineering Notebook and Designing Lesson 05.

U3a-L1 November 1, 2010 DRILL – Using the words at the bottom, complete the sentences in your notebook. The ____ includes identifying a problem, looking.

The Engineering Design Process

August 28, 2008 I1-4 With 1 partner:

U3d-L11 December 15, 2009 DRILL Sit with your Mechanical Basketball Shooter partner Get out your notebooks.

Instant Design Challenge

New Engineering Design Process

August 29, 2008 I1-5 With 1 partner:

Presented by: First Last

Engineering Design Process

Engineering Design Process

Engineering Design Process

Module C: Presentation The Engineering / Design Process

The Engineering Design Process

The Design Process What Is Design? What Is a Design Process?

A Design Process BW: What are the steps of the Design Process????? No Google! Do you have a lock????? What’s the combo?

Design Process for Engineering

Engineering Design Process

Engineering Design Process

The Engineering Design Process

Engineering Design Process

Instant Design Challenge

Problem Solving Method S.P.I.C.E.

Instant Design Challenge

2) Identify Requirements 1) Define the Problem 3) Gather Information

The Design Process.

The Engineering Design Process

Instant Design Challenge

An engineer is testing a prototype and discovers a flaw in the design of the product. What should the next step in the design process be? Bell work

The Engineering Design Process

Engineering Design Process

Engineering Design Process

The Engineering Design Process

Presentation transcript:

IOT POLY ENGINEERING I Using your handout of the design process steps place check next the items asked for as they appear on the screen. These are the items that require a response for turning in your design process steps. 2. Next, AFTER YOU GIVE A RESPONSE (not now), draw a line through that design process item. As in the example below. Design Process a. What must your solution accomplish?

IOT POLY ENGINEERING I1-3 1.Test model/prototype to ensure that it works as designed. 2.Calibrate your model/prototype to satisfy all criteria and constraints. DOCUMENT YOUR TESTING PROCESS and RESULTS Test and Evaluate Outcome: Sentences, Lists, Charts, Sketches

IOT POLY ENGINEERING I1-3 1.Document any changes you make or need to make to your selected design. 2.Implement those changes to your model / prototype. 3.Retest. Refine the Design Outcome: Sentences, Lists, Charts, Sketches

IOT POLY ENGINEERING I1-3 PROBLEM SOLVING 1.FIRST, MAKE A WORKING MODEL used to test your design concept. NEXT, complete steps 6 & 7 of the design process. 2.These steps need to be added to your steps 1,3&4. 3.Steps 2 & 5 do not have to be included because step 2 was done through the notes taken in your notebook and step 5 is making a working model used to test your design concept. 4.

IOT POLY ENGINEERING I1-3 PROBLEM SOLVING ROBOT ARM END EFFECTOR. Challenge Problem: Design a gripping wire snare harness end effector for a robot arm that will grip and snare (hold) a pen or pencil when activated (moved). Use your design process responses, notes, video ideas, and your own ideas for help. What gripping wire harness looks like. Robot Arm WITH A PARTNER & THE MATERIALS GIVEN SOLVE THE CHALLENGE You have this class period to work on The Challenge Problem AND Step 6&7. Unfinished steps must be done for homework.