Multi Tester Miss Begum. Bell Work Write down what you know about the following equipment / machinery: Pillar drill File Wet & dry paper Line bender Soldering.

Slides:

Advertisements

Similar presentations

A Picture Diagram of a Torch

Advertisements

Electric Circuit By:Griselda and Jose A Complete Circuit A close circuit is a kind of electric circuit in which the path that the electrons follow forms.

What are conductors and insulators?

AnaSonde Assembly. What is the AnaSonde? *Reads temperature, pressure, and humidity data from the atmosphere *After it is sent into the atmosphere, it.

Jiggy Bot Aka Cyclops.

Lesson Objectives To learn how to solder components onto a circuit board safely and correctly. Success Criteria Must Be able to understand the health and.

Systems and Control – Fuse Tester Design and Technology Present NC levelTarget for end of Key Stage Name:Subject teacher: Teaching group:Tutor: Assessment.

Learn-to-Solder Exercise: Practice Flasher Circuit AEM 1905: Spaceflight with Ballooning University of Minnesota.

PRACTICAL ELECTRONICS MASTERCLASS (Mr Bell) 1. Fault finding A fault is when a piece of equipment does not work the way it had been intended too. Fault.

Manufacturing Systems

Painting a Portrait Lesson 10: Hair and Facial Features.

SpectraSonde Assembly. What is the SpectraSonde? Reads temperature, pressure, and humidity data from the atmosphere. The SpectraSonde doesn’t fly like.

Photo Clip Assessed Piece of Work Level What I need to do to improve my strand level Design ideas (Strand 2) Production plan (Strand 3) Practical work.

Soldering Safety – Soldering Irons are very HOT! Name: 1. When I am not using the soldering iron, I should return it to the holder because________ _________________________.

Electrical Circuits Utah Underwater Robotics Instruction Slides.

IOT POLY ENGINEERING 4-01 DRILL April 20, 2009 Ohm’s Law states that voltage equals current times resistance, V=IR. Solve the following problems. Draw.

AnaSonde-3M Assembly. What is the AnaSonde-3M? The AnaSonde-3M reads temperature, pressure and humidity data from the atmosphere. After the AnaSonde is.

Circuits Topic- Seating Plan. Electric Circuits Level 4Level 5Level 6 Use circuit components to construct a series circuit Describe how a torch circuit.

Do you have control? Mr. Caudy Systems and Computer Control.

What are conductors and insulators?. What is a conductor? A conductor is something which allows electricity to flow through. An example of a conductor.

Discovery Kits: Electricity. 1.5 V Battery Batteries in series Closed switch Open switch V Motor Components.

Science Electricity: Lesson 8: How a Bulb Works Day 1.

Automotive Electricity and Electronics, 3/e By James D. Halderman Copyright © 2011, 2009, 2005 Pearson Education, Inc., Upper Saddle River, NJ All.

Electricity and Magnetism. What Do You Think? Using a T-Chart, write down everything you know about electricity and magnetism Electricty Magnetism.

Electronic Schematics How we can draw electronic circuits.

DESIGN PROCESS: DANCE PAD AND LIGHTS Phoenix Graves & Tyler Hummel.

PRACTICAL ELECTRONICS

Electronics Speaker Project Mr Sanders.

Front view LED’s pushed into place Buzzer bolted on Fuse holder bolted on.

WARM UP 10/20/15 1.Your Warm Up should be glued into your notebook immediately! 2.DO NOT TOUCH any of the materials at your table. If you do, you may lose.

Exploring Electricity

ELC Textiles - Optional Unit 15 Designing and Making a Fabric Container for Personal Possessions Work by:

Oisture Tester How to Solder. Learning Objectives Understand the soldering process Practice soldering Continue with design ideas Produce an information.

Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.

Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.

Lv3: Identify dangers of using electricity Lv4: Build simple circuits which match illustrations. Lv5: Test materials to see if they are conductors or insulators.

Robot Glossary COPING SAWTENON SAW TRI SQUARECHISEL MALLET STEEL RULER MARKING GAUGEFILE SANDPAPER BRADAWLBENCH HOOKPILLAR DRILL.

LED Flashlight.

Continuity tester a handy tool for testing circuits

Y8 T4 – Electricity and Electrical circuits 1

Research 5 different electronic toys

PRACTICAL ELECTRONICS

Electricity L1: Circuit Diagrams

Electric Circuits (12.2).

Basic Electronics Year 10.

Electric Circuits (12.2).

What are conductors and insulators?

Practice #3—Kitchen Batteries, Series, and Parallel

Match the circuit symbols How many of these can you name?

You have 5 minutes to check the resistors you have done.

Churchmead Design Technology

Conductors and Insulators

Be able to solder the capacitor and chip holder in place on the PCB.

My Key Fob By Stuart Peters.

Draw and interpret circuit diagrams containing sources, switches, resistors (fixed and variable), heaters, thermistors, light-dependent resistors, lamps,

Learn-to-Solder Exercise: Practice Flasher Circuit

How can I remember this information?

Electromagnets Lesson 3

My Key Fob Alix McAra 1.6.

What are conductors and insulators?

Have created a neat drawing of a circuit with specific features shown.

How to Write a Specification

Making a simple steady hand game

By Gerry Crenshaw WD4BIS

Plan of Making (Flow Charts)

Plan of Making (Flow Charts)

Top Tips for ‘subject’ During one of your lessons in June you will be doing your Design and Technology Exam it is 45mins and out of 45 marks . ( chart.

Presentation transcript:

Multi Tester Miss Begum

Bell Work Write down what you know about the following equipment / machinery: Pillar drill File Wet & dry paper Line bender Soldering iron

The Big Picture Multi Tester Electronics Plastic Pro Desktop Poster Mr Fuse

Learning Outcomes By the end of the lesson you will: Make a multi tester Draw your multi tester on Pro Desktop Present your multi tester

Learning Outcomes How will you meet your learning outcomes? Make a multi tester  Make the casing  Make the electronics Draw your multi tester on Pro Desktop  Use pro desktop software to draw your multi tester Present your multi tester  Make a poster promoting your multi tester  Make Mr Fuse

Group Work Task Arrange yourselves into groups of 4 Decide who will: 1) Make the electronics 2) Make the plastic casing 3) Draw the multi tester on pro desktop (2 people) You will work as a group to: 1) Make your poster 2) Make Mr Fuse

Pillar Drill What do I have to drill? You are going to use the pillar drill to dill holes in your plastic

Line Bender Where do I have to bend my plastic? We use the line bender to bend the plastic on the dotted lines

Electronics What do I have to make? You will make this circuit by soldering the components together LED Resistor Battery Clip

Assessment You groups will be marked in the following table: GroupElectronicsCasingPro Desktop PosterMr FuseTeamworkTotal

Review / Preview Review Our learning outcomes were to: Make a multi tester Draw your multi tester on Pro Desktop Present your multi tester Have we met our learning outcomes? How have we met our learning outcomes? Preview Next lesson we will be carrying on with the touch light project. This will help us understand what makes a calendar successful. It will help us design our own unique calendars.