FEATURES HD-SDI COLOR CCTV CAMERA USER’S MANUAL SDI-BS212 SDI-BS212T 1/3” Panasonic 2.1M Pixel Progressive Scan Color CMOS Sensor Video Out (BNC) with NTSC/PAL Selectable Dual Output – Megapixel HD CCTV (BNC) and SD CCTV (BNC) out Defog (Visibility Enhancement on the Low Contrast Scene) Digital Zoom (x8) Sens-up (x8) Flicker Suppression DNR (2D & 3D Noise Reduction) DPC (Dead Pixel Compensation) 2 Auto (AE/AWB) Control HLC/BLC Support (High Light / Back Light Compensation) C / CS Mount Lens Rear OSD Control Board RS-485 Support External Day&Night In put Support Option : Mechanical TDN (ICR) Option : Dual Voltage (DC12V & AC 24V) / Free Voltage (AC 230V) SPECIFICATIONS MEMO * In accordance with customers’ request and OSD controller’s option, the specifications can be fixed or changed without notice. MODEL SELECTION RS-485TDNPOWERPIXELMODEL OXDC 12V2.1MSDI-BS212 SDI-BS212T O O DC 12V2.1M

PRECAUTIONS Do not install the camera in extreme temperature conditions. -Only use the camera under conditions where temperatures are between -10°Cand +50°C. Be especially careful to provide ventilation when operating under high temperatures. Do not install or use the camera in an environment where the humidity is high. -It can cause the image quality to be poor. Do not install the camera under unstable lighting conditions. -Severe lighting change or flicker can cause the camera to work improperly. Never use the camera close to a gas or oil leak. -It can cause malfunctions to occur. Do not disassemble the camera. -There are no user-serviceable parts inside it. Do not touch the front lens of the camera. -It is one of the most important parts of the camera. Be careful not to be stained by fingerprint. Never keep the camera face to strong light directly. -It can damage the image sensor. Do not drop the camera or subject them to physical shocks. -It can cause malfunctions to occur. Do not expose the camera to rain or spill beverage on it. -If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components. Do not expose the camera to radioactivity. -If exposed to radioactivity the image sensor will fail. * NOTE * If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur. Please check that the power satisfies the normal specification before connecting the camera. COMPOSITION NAME OF EACH PART Camera (W/O Lens)C-Mount ringL- Wrench Camera holderManual 1. Lens (Option) 4. Auto iris lens connector Screw 2. Flange-back adjusting ring 3. Camera holder screw hole. 1.Auto iris lens (Option) : This is the lens used with the camera. 2.Flange-back adjusting ring : A screw is provided to fix the lens mount. 3.Camera holder screw hole : Mounting base for installing the camera. 4.Auto iris lens connector : This connected supplies DC control. Signals needed to control the auto iris lens. UPPER REAR 2. Video out terminal 3. OSD controller 5. I/O port 6. Power port 1.HD-SDI Video out terminal : BNC terminal for HD-SDI video signal output. 2.Video out terminal : Sends video signal and connects to the video input terminal of the monitor. 3.OSD ControllerSET UP : Used for the menu display. This button can be used to confirm settings. After changing the value of the selected function or current conditions.UP & DOWN : Used for selecting items by moving the cursor up or down on the menu screen.LEFT & RIGHT : Used when changing item values, by moving the cursor to left or right on the menu screen. 4.Power LED : Illuminates when power is supplied. 5.I/O PortRS-485 Control port : You can control SETUP MENU through this port by using external controllers like a remote controller that RS-485 communication is supported.MD Output port : Motion detection signals are output through this port.GND : GroundD&N Input port : You can switch to Day & Night mode by connecting an external signal to this port. 6.Power input : DC 12V, DC 12V / AC 24V (Dual Voltage), AC 230V DIMENSION 1. HD-SDI Video out terminal 4. Power LED