Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems.

Slides:



Advertisements
Similar presentations
Date of download: 6/3/2016 Copyright © ASME. All rights reserved. From: Two-Phase Convective Cooling for Ultrahigh Power Dissipation in Microprocessors.
Advertisements

Date of download: 6/6/2016 Copyright © ASME. All rights reserved. From: Three-Dimensional Integrated Circuit With Embedded Microfluidic Cooling: Technology,
Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: Performance and Design Comparison of a Bulk Thermoelectric Cooler With a Hybrid.
Date of download: 6/25/2016 Copyright © ASME. All rights reserved. From: Design and Modeling of One Refrigeration Ton Solar Assisted Adsorption Air Conditioning.
Date of download: 6/25/2016 Copyright © ASME. All rights reserved. From: Thermal Effect on Microchannel Electro-osmotic Flow With Consideration of Thermodiffusion.
Date of download: 6/28/2016 Copyright © ASME. All rights reserved. From: Convective Heat Transfer and Contact Resistances Effects on Performance of Conventional.
Date of download: 6/30/2016 Copyright © ASME. All rights reserved. From: Analysis of Thermal Stress and Its Influence on Carrier Mobility in Three-Dimensional.
Date of download: 7/7/2016 Copyright © ASME. All rights reserved. From: Energy Conservative Dissipative Particle Dynamics Simulation of Natural Convection.
Date of download: 9/16/2016 Copyright © ASME. All rights reserved. From: Thermoelectric Performance of Novel Composite and Integrated Devices Applied to.
Date of download: 9/17/2016 Copyright © ASME. All rights reserved. From: Heat Conduction Effect on Oscillating Heat Pipe Operation J. Thermal Sci. Eng.
Date of download: 9/19/2016 Copyright © ASME. All rights reserved. From: Detailed Heat Transfer Measurements Inside Rotating Ribbed Channels Using the.
Date of download: 9/20/2016 Copyright © ASME. All rights reserved. From: Experimental Investigation on Freezing of Water Falling Film on Vertical Bank.
Date of download: 9/20/2016 Copyright © ASME. All rights reserved. From: Simulation and Optimization of Drying of Wood Chips With Superheated Steam in.
Date of download: 11/12/2016 Copyright © ASME. All rights reserved. From: An Open Loop Pulsating Heat Pipe for Integrated Electronic Cooling Applications.
Date of download: 9/26/2017 Copyright © ASME. All rights reserved.
From: Optimal Shapes of Straight Fins and Finned Heat Sinks
Date of download: 9/27/2017 Copyright © ASME. All rights reserved.
From: Thermal-Hydraulic Performance of MEMS-based Pin Fin Heat Sink
Date of download: 9/30/2017 Copyright © ASME. All rights reserved.
Date of download: 10/5/2017 Copyright © ASME. All rights reserved.
Date of download: 10/8/2017 Copyright © ASME. All rights reserved.
Date of download: 10/9/2017 Copyright © ASME. All rights reserved.
From: Pressure Surge During Cryogenic Feedline Chilldown Process
Date of download: 10/10/2017 Copyright © ASME. All rights reserved.
Date of download: 10/14/2017 Copyright © ASME. All rights reserved.
From: Nanoscale Heat Conduction Across Metal-Dielectric Interfaces
Date of download: 10/19/2017 Copyright © ASME. All rights reserved.
Date of download: 10/24/2017 Copyright © ASME. All rights reserved.
Date of download: 10/25/2017 Copyright © ASME. All rights reserved.
Date of download: 10/26/2017 Copyright © ASME. All rights reserved.
Date of download: 10/28/2017 Copyright © ASME. All rights reserved.
Date of download: 10/29/2017 Copyright © ASME. All rights reserved.
Date of download: 10/30/2017 Copyright © ASME. All rights reserved.
Date of download: 11/1/2017 Copyright © ASME. All rights reserved.
Date of download: 11/1/2017 Copyright © ASME. All rights reserved.
Date of download: 11/2/2017 Copyright © ASME. All rights reserved.
From: Heat Exchanger Efficiency
Date of download: 11/3/2017 Copyright © ASME. All rights reserved.
Date of download: 11/4/2017 Copyright © ASME. All rights reserved.
Date of download: 11/4/2017 Copyright © ASME. All rights reserved.
From: Numerical Optimization of the Thermoelectric Cooling Devices
From: Modeling Transmission Effects on Multilayer Insulation
Date of download: 11/6/2017 Copyright © ASME. All rights reserved.
Date of download: 11/6/2017 Copyright © ASME. All rights reserved.
Date of download: 11/7/2017 Copyright © ASME. All rights reserved.
Date of download: 11/11/2017 Copyright © ASME. All rights reserved.
Date of download: 11/12/2017 Copyright © ASME. All rights reserved.
Date of download: 11/15/2017 Copyright © ASME. All rights reserved.
From: Design of a Cooling Guide Catheter for Rapid Heart Cooling
Date of download: 11/15/2017 Copyright © ASME. All rights reserved.
Date of download: 12/19/2017 Copyright © ASME. All rights reserved.
Date of download: 12/19/2017 Copyright © ASME. All rights reserved.
From: Impact of Interface Resistance on Pulsed Thermoelectric Cooling
Date of download: 12/22/2017 Copyright © ASME. All rights reserved.
Date of download: 12/22/2017 Copyright © ASME. All rights reserved.
Date of download: 12/22/2017 Copyright © ASME. All rights reserved.
Date of download: 12/24/2017 Copyright © ASME. All rights reserved.
Date of download: 12/24/2017 Copyright © ASME. All rights reserved.
From: Vapor Chamber Acting as a Heat Spreader for Power Module Cooling
Date of download: 12/25/2017 Copyright © ASME. All rights reserved.
Date of download: 12/25/2017 Copyright © ASME. All rights reserved.
Date of download: 12/25/2017 Copyright © ASME. All rights reserved.
Date of download: 12/26/2017 Copyright © ASME. All rights reserved.
Date of download: 12/27/2017 Copyright © ASME. All rights reserved.
Date of download: 12/27/2017 Copyright © ASME. All rights reserved.
From: An Investigation of a Tunable Magnetomechanical Thermal Switch
Date of download: 12/31/2017 Copyright © ASME. All rights reserved.
From: Electrohydrodynamics of Thin Flowing Films
Date of download: 3/4/2018 Copyright © ASME. All rights reserved.
Date of download: 3/4/2018 Copyright © ASME. All rights reserved.
Presentation transcript:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / A schematic diagram of a single-element pair of thermoelectric coolers. Thermoelectric materials, typically n- and p-type semiconductors, are electrically connected in series. The geometry is such that the elements are thermally in parallel, drawing heat from the left of the figure and dissipating heat to the right. A thermoelectric element-based model (or traditional model) for cooler performance is developed from the elements shown, including the material properties of the elements and the temperatures of the hot and cold junctions, Th and Tc, respectively. Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / The minimum cold-side temperature achievable by a thermoelectric cooler (nondimensionalized as Tc,min∕Th) is shown as a function of the nondimensional figure of merit, ZTh. The dashed line illustrates ideal cooler performance as predicted by traditional thermoelectric theory. Various experimental results from literature are overlaid, based on the published experimental cooling performance, Tc∕Th and experimentally measured figure of merit, ZTh.. The degree of departure from the theoretically predicted performance is distinctly more significant for coolers based on low-dimensional materials. Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / A thermoelectric cooler is shown schematically at the left. The electrically active elements are shown interconnected as in Fig.. Additional elements that determine cooler performance are shown including the finite thermal conductance between the source of heat to be cooled and the finite conductance between the hot junctions and the ambient environment. To the right, a one- dimensional thermal model is shown with each isothermal region labeled (Ta, Th, Tc, and Ts) and one-dimensional approximations of the thermal conductances shown (exit conductance, Kh, element array conductance, K, entry conductance, Kc). Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / The nondimensional minimum cold-side temperature is shown as a function of the cooler’s relative exit thermal conductance. The performance predicted by thermoelectric system theory (current work) as well as traditional thermoelectric theory is shown for values of thermoelectric figure of merit, ZTh=ZeTa=0.5, 1.0, and 2.0. As the exit thermal conductance decreases (due to poor heat sinking and/or miniaturization of the thermoelectric element array), the minimum temperature approaches 1.0 (no cooling below the ambient temperature). The performance predicted by traditional theory is also shown as dashed lines. Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / The nondimensional maximum cooling power is shown as a function of the cooler’s relative exit thermal conductance. The performance predicted by thermoelectric system theory (current work) is shown for values of thermoelectric figure of merit, ZTh=ZeTa=0.5, 1.0, and 2.0, each for two values of the relative entry thermal conductance. As the exit or entry thermal conductance is decreased (due to poor heat sinking, highly localized or poorly attached heat source, and/or miniaturization of the thermoelectric element array), cooling power is degraded. The performance predicted by traditional thermoelectric theory is also shown for each value of the figure of merit. Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / A schematic diagram of a thermoelectric cooler is shown with elements fabricated on a substrate, which in turn is mounted on a heat sink as a means of heat removal. A single thermoelectric element pair is shown for simplicity, however multiple elements may be arrayed and utilized. To the left, two schematics of a typical cross section are shown. The upper section shows active thermoelectric elements of a certain area, Ae, as well as an electrically inactive “fill” area, Af. The lower schematic depicts a representative section from a cooler that may be fabricated from vertically aligned wire. The area between each wire as well as between the n- and p-wire arrays constitutes the electrically inactive region, Af. Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / The nondimensional cold side temperature of a cooler is shown as a function of cooler element length, L. The cooler is modeled as dissipating heat through a substrate (λsub=150Wm−1K−1,t=300μm) on a semi-infinite heat sink (λsink=300Wm−1K−1). The predicted performance for several geometries and material properties reflecting a ZTa of 1.0 and a single representative result at ZTa=5 are shown. The degradation of performance as the element length decreases, the degree of degradation being a function of the element fill factor, β, and the relative thermal conductivity of the fill material λe∕λf. Thermal conductivity ratios are shown representing what would be found using a fill material of ambient air and silicon dioxide. The model illustrates the influence of scale and cooler structure, showing conditions where a microscale element with a ZTa of 5 may be outperformed by a cooler of larger scale and a ZTa of 1.0. Figure Legend:

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: The Compatibility of Thin Films and Nanostructures in Thermoelectric Cooling Systems J. Heat Transfer. 2006;129(7): doi: / Cooling power density of a cooler is shown as a function of cooler element length, L. The thermal conductance between the hot- side of the cooler and the ambient temperature is modeled as the airflow limit, Kh=m ̇ Cp. The predicted performance for three values of cooling fluid mass flow rate are shown with all coolers having materials exhibiting a ZTa of 1.0. Performance for a heat source held at the ambient temperature (Ts∕Ta=1) and a source operating below ambient temperatures (Ts∕Ta=0.85) are shown. The loci of maximum shifts to longer element lengths as the available hot side heat dissipation decreases, contrary to the 1∕L behavior predicted by traditional thermoelectric element theory. Figure Legend: