1 ANNEXURE PROJECT TITLE : A Novel Power Management Control Strategy for Renewable Energy Power System SUBMITTED BY : N.SAHUL HAMEED V.DINESH BABO P.PURSOTHAMAN.

Slides:



Advertisements
Similar presentations
ECE Electric Drives Topic 6: Voltage-Fed Converters Spring 2004.
Advertisements

DC Choppers 1 Prof. T.K. Anantha Kumar, E&E Dept., MSRIT
7. Introduction to DC/DC Converters
EXPERIMENTAL STUDY AND COMPARATIVE ANALYSIS OF TRANSFORMER HARMONIC BEHAVIOUR UNDER LINEAR AND NONLINEAR LOAD CONDITIONS.
Introduction to DC-DC Conversion – Cont.
Professor Sung-Yeul Park
DC Choppers 1 Prof. T.K. Anantha Kumar, E&E Dept., MSRIT
NAA MULTILEVEL INVERTERS (MLI)  Main feature  Ability to reduce the voltage stress on each power device due to the utilization of multiple.
Power Electronics Lecture-10 D.C to D.C Converters (Choppers)
Presented By: Er. Ram Singh (Asstt. Prof.) Deptt. Of EE
Copyright by UNIT III DC Choppers 4/17/2017 Copyright by
DC-DC Switch-Mode Converters
Instrumentation & Power Electronics
DC bus for photovoltaic power supplying computing loads
Photovoltaic Power Converter
Chapter 8 Inverters AC Power • Inverters • Power Conditioning Units • Inverter Features and Specifications.
POWER SUPPILES LECTURE 20.
EE462L, Spring 2014 H-Bridge Inverter Basics
LECTURE 9 INTRO TO POWER ELECTRONICS
Power Electronics Notes 07A Introduction to DC/DC Converters
Switching rules Either A+ or A– is always closed, but never at the same time * Either B+ or B– is always closed, but never at the same time * *same time.
Switching DC Power Supplies
Power Electronics and Drives (Version ) Dr. Zainal Salam, UTM-JB 1 Chapter 3 DC to DC CONVERTER (CHOPPER) General Buck converter Boost converter.
ET3380 Principles and Methods of Electric Power Conversion David Morrisson MS,MBA Week 1.
Fundamentals of Power Electronics and Power System with MATLAB
A New Full-Protected Control Mode to Drive Piezoelectric Transformers in DC-DC Converters J.A.M. Ramos, M.A.J. Prieto, F.N. Garica, J.D. Gonzalez, F.M.F.
MULTILEVEL INVERTERS By Vaishnavi.
Lecture # 12&13 SWITCHING-MODE POWER SUPPLIES
Michael Ikerionwu 4 th year Electronic Engineering.
February 2, 2004Grainger Center for Electric Machinery and Electromechanics 1 Energy Source Diversification Patrick Chapman Asst. Professor UIUC Sponsored.
Chapter 6 Voltage Regulators By En. Rosemizi Bin Abd Rahim EMT212 – Analog Electronic II.
Adviser : Cheng-Tsung Lin Student :Nan-hui Hsieh
Balance of Systems (BOS)
A NOVEL CONTROL METHOD OF DC-DC CONVERTERS Dr.M.Nandakumar Professor Department of Electrical engineering Govt. Engineering College Thrissur 1 Dept. of.
PARISUTHAM INSTITUTE OF TECHNOLOGY AND SCIENCE
EMT212 – Analog Electronic II
Introduction to DC-DC Conversion – Cont.
Students: Thomas Carley Luke Ketcham Brendan Zimmer Advisors: Dr. Woonki Na Dr. Brian Huggins Bradley University Department Of Electrical Engineering 2/28/12.
Date of download: 5/28/2016 Copyright © ASME. All rights reserved. From: Investigation on a Modified 11-Level Cascaded Inverter Fed by Photovoltaic Array.
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 28, NO. 11, NOVEMBER 2013 Yuanmao Ye and K. W. E. Cheng A Family of Single-Stage Switched-Capacitor–Inductor.
Rectifier A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which.
Bridge Rectifier Circuit with Working Operation and Their Types.
CLOSED LOOP SPEED CONTROL OF DC MOTOR WITH PWM TECHNIQUE
A NOVEL CONTROL STRATEGY FOR HYBRID AC/DC MICRO GRID SYSTEMS
Power Electronics and Power Conversion, Assiut University 1 Photovoltaic Systems Ahmed G. Abo-Khalil.
A SINGLE PHASE TO THREE PHASE CONVERTER USING QUASI Z SOURCE NETWORK
Chapter 6: Voltage Regulator
Florian Krismer Swiss Federal Institute of Technology (ETH) Zurich
بحث مشترك منشور فى مؤتمر دولى متخصص (منشور ، التحكيم علي البحث الكامل) B. M. Hasaneen and Adel A. Elbaset البحث التاسع 12 th International Middle East.
SMPS.
DOUBLE INPUT Z-SOURCE DC-DC CONVERTER
Eric A Lewis Enstore director
University of Calabria, Italy
DOUBLE INPUT Z-SOURCE DC-DC CONVERTER
DESIGN OF PV SYSTEM INTERCONNECTED WITH EU
D. Menniti, N. Sorrentino, A. Pinnarelli, M. Motta, A. Burgio and P
PROBLEM DEFINITION: In general, various single-input single-output dc–dc converters with different voltage gains are combined to satisfy the requirement.
IMPEDENCE - SOURCE INVERTER FOR MOTOR DRIVES
Switching DC Power Supplies
DOUBLE INPUT Z-SOURCE DC-DC CONVERTER
DC-DC PWM Converters Lecture Note 5.
Converter principles and modelling
Basics of interfacing PV to the Grid
Five level diode clapmed inverter
Introduction to H-Bridge
Photovoltaic Systems Engineering Session 10
List of contents Introduction
DC-DC Switch-Mode Converters
Chris Leonard and Baylor Howard Advisor: Dr. Jing Wang
Presentation transcript:

1 ANNEXURE PROJECT TITLE : A Novel Power Management Control Strategy for Renewable Energy Power System SUBMITTED BY : N.SAHUL HAMEED V.DINESH BABO P.PURSOTHAMAN REVIEW NUMBER : 02 REVIEW DATE :

Overview Introduction Objective Proposed Topology Operational Principles(two stages) Matlab/PSIM Simulation Results Describe Project Build and tests Experimental Test results Conclusion

Introduction and Scope Comparing single-stage grid-connected photovoltaic (PV) system with power quality improvement, in this project, a high-capacity single phase grid-connected PV system based on wide range conversion converter + inverter is proposed, which not only allows a wide range of input voltage, but also compensates unbalance current of the local load comparing in the case of three-phase three-wire PV system. This project explains the control principle of each power stage of the system and the simplified cost effective control strategy of combination of PV grid-connected generation in detail. then the Simulation and Experimental results of the proposed system represents the features of the proposed system.

Introduction and Scope Conversion from low-voltage dc to high-voltage ac for grid- tie applications were proposed to deal with specific issues such as high efficiency, low cost, and safety. The aim of this article is to introduce and discuss the main features of these relatively new circuit topologies that deal with these practical design issues. The aim of this article is to introduce and discuss the main features of these relatively new circuit topologies that deal with these practical design issues

Grid Tie converter system For low-voltage dc energy sources, a power conditioning system (PCS) is needed to convert the energy sources to a higher-voltage dc before making it to ac for grid tie applications. Solar photovoltaic (PV) and fuel cells are perhaps the most well- known and prospective energy sources with low-voltage dc output. A thermoelectric generator, a battery, and an ultra capacitor are also examples of such low-voltage dc energy sources. Recently, numerous circuit topologies for the power conversion from low- voltage dc to high-voltage ac for grid-tie applications were proposed to deal with specific issues such as high efficiency, low cost, and safety.

6 INTRODUCTION : PV SYSTEM  The PV power system can be classified into two types: stand- alone PV system and grid-connected PV system.  In remote or isolated regions where power grid can not extend to, stand-alone PV schemes have found a fairly wide application to meet the need for small but essential electric load.

Functional block diagram

Grid-connected /Stand alone PV system with power quality comprehensive compensator

Power flow of the system with nonlinear load

Proposed System The system aims transferring the photovoltaic (PV) power to the ac load and paralleled with the utility. The dc-dc converter is used to boost the PV voltage to a level higher than the peak of the voltage utility such that the inverter can provide the ac voltage without requiring the transformer. The dc-dc converter is also responsible for tracking the maximum power point of the PV modules to fully utilize the PV power. The shortage of load power from the PV module is supplemented by the utility. On the contrary, the excessive power from the PV module to the load can be fed to the utility. The balance of power flow is controlled through the inverter. The inverter also is used to act always as an active power filter to compensate the load harmonics and reactive power such that the input power factor is unity

12 INTRODUCTION-wide Range conversion Converter  New technologies are emerging that require a wide range voltage conversion such as integrated circuits with voltage of power supply of 3.3 V and 1.5 V, automotive systems, aeronautical systems and telecommunications systems, solid state lighting systems.  The above requirements can be satisfied using conventional PWM converters by: operating at extremely low or high duty ratios with the corresponding limitations on the finite commutation times of the switching devices, or using a step-down or step-up transformer with the corresponding difficulties in switching surges and operating frequencies.

13 INTRODUCTION Continued…  In theory, larger conversion ratios can be obtained by properly adjusting the modulating control signal of the converter. In practice, the maximum and the minimum attainable conversion ratios for the conventional converters are limited by the characteristics of the switching devices.  A scheme that provides larger conversion ratios without an isolation transformer is a cascade connection. This scheme is a multistage approach that consists of various converters connected in cascade.  One of the major advantages of these converters is a high gain; however, a major drawback is that the total efficiency may be low if the number of stages is high

14 OBJECTIVE  In this project, quadratic boost buck converter (boost 2 -buck) is derived from the quadratic converters is proposed. This topology presents non-pulsating input and output current.  It has operations equivalent to a cascade converter consisting of two boost converter and one buck converter, but with the advantage of using single active switch.

PROPOSED HIGH VOLTAGE TRANSFORMERLESS DC-DC CONVERSION TOPOLOGY

Simulation Diagram: Schematic of Proposed High Step Up Converter

Simulation results of proposed converter

Circuit Description Circuit Description In proposed circuit, It has operations equivalent to a cascade converter consisting of two boost converter and one buck converter, but with the advantage of using single active switch. This topology presents non-pulsating input and output current. The schematic of the High step Up Boost converter is show in figure. The operation in continuous conduction mode in steady state consists of two states.

Design Formulas The voltage gain is given by,- (Discontinuous) The normalized inductor time constant is defined as: The voltage gain is given by(Continouous) conduction mode)

PROPOSED INVERTER (two stages)

Switching rules Either A+ or A– is closed, but never at the same time * Either B+ or B– is closed, but never at the same time * *same time closing would cause a short circuit from Vdc to ground (shoot-through) *To avoid dhoot-through when using real switches (i.e. there are turn-on and turn-off delays) a dead-time or blanking time is implemented Corresponding values of Va and Vb A+ closed, Va = Vdc A– closed, Va = 0 B+ closed, Vb = Vdc B– closed, Vb = 0 Bridge Inverter Basics – Creating AC from DC Vdc Load A+ B+ A– B– Va Vb Single-phase H-bridge (voltage source) inverter topology:

Corresponding values of Vab A+ closed and B– closed, Vab = Vdc A+ closed and B+ closed, Vab = 0 B+ closed and A– closed, Vab =–Vdc B– closed and A– closed, Vab = 0 The free wheeling diodes permit current to flow even if all switches are open These diodes also permit lagging currents to flow in inductive loads Vdc Load A+ B+ A– B– Va Vb BRIDGE INVERTER + Vdc − Utility interfacing Inverter Circuit

Corresponding values of Vab A+ closed and B– closed, Vab = Vdc A+ closed and B+ closed, Vab = 0 B+ closed and A– closed, Vab =–Vdc B– closed and A– closed, Vab = 0 The free wheeling diodes permit current to flow even if all switches are open These diodes also permit lagging currents to flow in inductive loads Vdc Load A+ B+ A– B– Va Vb BRIDGE INVERTER + 0 −

Corresponding values of Vab A+ closed and B– closed, Vab = Vdc A+ closed and B+ closed, Vab = 0 B+ closed and A– closed, Vab =–Vdc B– closed and A– closed, Vab = 0 The free wheeling diodes permit current to flow even if all switches are open These diodes also permit lagging currents to flow in inductive loads Vdc Load A+ B+ A– B– Va Vb BRIDGE INVERTER − Vdc +

Corresponding values of Vab A+ closed and B– closed, Vab = Vdc A+ closed and B+ closed, Vab = 0 B+ closed and A– closed, Vab =–Vdc B– closed and A– closed, Vab = 0 The free wheeling diodes permit current to flow even if all switches are open These diodes also permit lagging currents to flow in inductive loads Vdc Load A+ B+ A– B– Va Vb BRIDGE INVERTER + 0 −

Simulation Diagram of Proposed 12 volt Photovoltaic inverter feeding Non-linear load without feeding utility

Simulation results of Proposed 12 volt Photovoltaic inverter feeding Non-linear load without feeding utility

Experimental Prototype Design Details To demonstrate the feasibility of the discussed PV system, a prototype was designed and implemented. The specifications of the system shown in fig are shown below: Solar array: Number of PV Module: 1 Rated power: 20W; Rated voltage: 12V; Rated current: 1.5A; Dc-dc power converter: Input voltage : 12 volt-400vol maximum Output voltage: Maximum 500V; Switching frequency: 20 kHz; Switch used: IRFP450,

Contin.., Inductors: L1 = 100uH L2 = 100uH Capacitors: Co = 470uF Diodes: Do,D1, D2, D3 = BY399

Cont.., Inverter: Switches Used: MOSFETs IRP450 (500Volts, 15 Amp max) Switching frequency: 5 kHz; Filter inductance: 1.5 mH Filter capacitor : 170uF Output voltage: 12V-500Volt, 50Hz; Load: 500VA In the proposed system, a LC filter is connected with the PV array output to filter the high frequencies drained by the dc-dc converter, and a series LC filter is connected between the converters to support the second-order component (100Hz) resented in the input inverter current.

Advantages of Proposed circuit: when compared with a converter cascade, it is  cheaper,  less bulky and  used circuit control simpler.

Applications of Proposed circuit: Suitable for automotive systems, Aeronautical systems Telecommunications systems and, solid state lighting systems