Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 SPECIFICATION FOR APPROVAL Title13.3” HD TFT LCD BUYERToshiba MODEL SUPPLIER LG Display Co., Ltd. *MODELLP133WH2 SuffixSPA1 *When you obtain standard approval, please use the above model name without suffix ( ● )Preliminary Specification ()Final Specification APPROVED BYSIGNATURE / / / Please return 1 copy for your confirmation with your signature and comments. Products Engineering Dept. LG Display Co., Ltd PREPARED BY REVIEWED BY SIGNATURE APPROVED BY J. Y. LEE / G.Manager D. Y. Kim / Manager C. J. Park / Engineer

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 NoITEM Page COVER 1 CONTENTS 2 RECORD OF REVISIONS 3 1GENERAL DESCRIPTION 4 2ABSOLUTE MAXIMUM RATINGS 5 3ELECTRICAL SPECIFICATIONS 3-1ELECTRICAL CHARACTREISTICS 6 3-2INTERFACE CONNECTION 8 3-3eDP SIGNAL TIMING SPECIFICATIONS 9 3-4SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERNECE POWER SEQUENCE 12 4OPTICAL SFECIFICATIONS 13 5MECHANICAL CHARACTERISTICS 16~18 6RELIABLITY 19 7INTERNATIONAL STANDARDS 7-1SAFETY EMC 20 8PACKING 8-1DESIGNATION OF LOT MARK PACKING FORM CT Code 21 9PRECAUTIONS 22 AAPPENDIX. Enhanced Extended Display Identification Data 24~26 Contents

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Revision NoRevision DatePageDescription EDID ver 0.0Mar All First Draft (Preliminary Specification) 0.1Mar Change model name (SPD1  SPA1) 4, 16 Change Surface Treatment (AG  Glare) 4, 6 Update Power Consumption 10 Update Timing Description 12 Update Power Sequence 13 Update Color Coordinates (Not Fix) 14 Update Gray scale (Not Fix) 21 Update International Standards Update EDID (8B)0.1 RECORD OF REVISIONS

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / General Description Active Screen Size13.3 inches diagonal Outline Dimension306.3 mm (H, Typ.) X mm (V, Typ.) X 3.0T mm (Max) Pixel Pitch X mm Pixel Format1366 horiz. by 768 vert. Pixels RGB strip arrangement Color Depth6-bit, 262,144 colors Luminance, White325 cd/m2 (Typ.5 PWM Duty = 100%) Power ConsumptionTotal 4.1W (Max.) Logic : 0.9W Mosaic), B/L : 3.2W VLED 12V ) Weight275g (Max) Display Operating ModeTransmissive mode, normally black Surface TreatmentGlare treatment of the front Polarizer RoHS ComplianceYes BFR / PVC / As FreeYes for all The LP133WH2 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmisive type display operating in the normally white mode. This TFT-LCD has 13.3 inches diagonally measured active display area with HD resolution (1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue sub- pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. The LP133WH2 has been designed to apply the interface method that enables low power, high speed, low EMI. The LP133WH2 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub- pixels, the LP133WH2 characteristics provide an excellent flat display for office automation products such as Notebook PC. General Features Control & DataPowerEDID signal & Power eDP Timing Control (Tcon) Block eDP Timing Control (Tcon) Block User connector 30 Pin TCLKs eDP 1Lane VCC Power Block Power Block DVCC, AVDD VGH, VGL, GMA GIP CLKs, DSC DVCC Source Driver (Bottom) EPI TFT-LCD Panel (HD, GIP+DRD, TN) AUX LED Backlight Ass’y LED Block LED Block VLED PWM LED_EN FB1~4 VOUT_LED

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Table 1. ABSOLUTE MAXIMUM RATINGS Storage Operation ParameterSymbol Values UnitsNotes MinMax Power Input Voltage VCC Vdc at 25  5  C Operating Temperature T OP 050 CC 1 Storage Temperature H ST CC 1 Operating Ambient Humidity H OP 1090%RH1 Storage Humidity H ST 1090%RH1 Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39  C Max, and no condensation of water.

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Electrical Specifications 3-1. Electrical Characteristics Table 2. ELECTRICAL CHARACTERISTICS The LP133WH2 requires two power inputs. The first logic is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second backlight is the input about LED BL.with LED Driver. ParameterSymbol Values UnitNotes MinTypMax LOGIC : Power Supply Input VoltageV CC V1 Power Supply Input Current MosaicI CC mA2 Power ConsumptionP CC W3 Power Supply Inrush CurrentI CC_P mA4 eDP ImpedanceZ eDP Ω4 BACKLIGHT : ( with LED Driver) LED Power Input VoltageV LED V6 LED Power Input CurrentI LED mA7 LED Power ConsumptionP LED W7 LED Power Inrush CurrentI LED_P mA8 PWM Duty Ratio5-100%9 PWM Jitter %10 PWM ImpedanceZ PWM kΩ PWM FrequencyF PWM Hz11 PWM High Level VoltageV PWM_H V PWM Low Level VoltageV PWM_L 0-0.3V LED_EN ImpedanceZ PWM kΩ LED_EN High VoltageV LED_EN_H V LED_EN Low VoltageV LED_EN_L 0-0.3V Life Time12,000--Hrs12

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Note) 1. The measuring position is the connector of LCM and the test conditions are under 25 ℃, fv = 60Hz, Black pattern. 2. The specified Icc current and power consumption are under the Vcc = 3.3V, 25 ℃, fv = 60Hz condition and Mosaic pattern. 3. This Power Consumption Spec. is measured for the Mosaic Pattern condition. 4. The below figures are the measuring Vcc condition and the Vcc control block LGD used. The Vcc condition is same as the minimum of T1 at Power on sequence. 5. This impedance value is needed for proper display and measured form eDP Tx to the mating connector. 6. The measuring position is the connector of LCM and the test conditions are under 25 ℃. 7. The current and power consumption with LED Driver are under the Vled = 12.0V, 25 ℃, Dimming of Max luminance and White pattern with the normal frame frequency operated(60Hz). 8. The below figures are the measuring Vled condition and the Vled control block LGD used. VLED control block is same with Vcc control block. 9. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue. 10. If Jitter of PWM is bigger than maximum, it may induce flickering. 11. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for more consistent brightness control at any specific level desired. 12. The life time is determined as the sum of the continuous operation time at which brightness of LCD at the typical LED current is 50% compare to that of minimum value specified in table 7 under general user condition. 10% 90% 0.5ms 3.3V 0V 10% 90% 0.5ms 12.0V 0V Rising time Vcc Rising time V LED

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 PinSymbolDescriptionNotes 1 NCNo Connection [Interface Chip] 1. LCD : SiW, SW0661(LCD Controller Including eDP Receiver) 2. System : TBD or equivalent * Pin to Pin compatible with eDP [Connector] HD2S030HA1, JAE or Equivalent [Connector pin arrangement] 2 GNDHigh Speed Ground 3 NCNo Connection 4 NCNo Connection 5 GNDHigh Speed Ground 6 Lane0_NSignal Link Negative Lane0 7 Lane0_PSignal Link Positive Lane0 8 GNDHigh Speed Ground 9 AUX_PSignal Auxiliary Positive Ch. 10 AUX_NSignal Auxiliary Negative Ch. 11 GNDHigh Speed Ground 12 VCCLCD Logic and driver power (3.3V Typ.) 13 VCCLCD Logic and driver power (3.3V Typ.) 14 NCNo Connection 15 GNDHigh Speed Ground 16 GNDHigh Speed Ground 17 HPDHot plug Detection Pin 18 GNDHigh Speed Ground 19 GNDHigh Speed Ground 20 GNDHigh Speed Ground 21 GNDHigh Speed Ground 22 LED_EN LED Backlight On/Off 23 PWMSystem PWM Signal input for dimming 24 NCNo Connection 25 NCNo Connection 26 VLEDLED Backlight Power (5V-21V) 27 VLEDLED Backlight Power (5V-21V) 28 VLEDLED Backlight Power (5V-21V) 29 VLEDLED Backlight Power (5V-21V) 30 NCNo Connection 3-2. Interface Connections Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1) This LCD employs two interface connections, a 30 pin connector is used for the module electronics interface and the other connector is used for the integral backlight system. The electronics interface connector is a model CABLINE-VS RECE ASS’Y [LCD Module Rear View]

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 DescriptionSymbolMinTypMaxUnitNotes Unit Interval for high bit rate (2.7Gbps/lane) UI_High_Rate-370-ps Range is nominal ±350ppm. DisplayPort Link Rx does not require local crystal for link clock generation Unit Interval for high bit rate (1.62Gbps/lane) UI_Low_Rate-617-ps Lane-to-Lane skew V Rx-SKEW- INTER_PAIR ps- Lane intra-pair skew V Rx-SKEW- INTRA_PAIR --100psFor high bit rate --300psFor reduced bit rate DescriptionSymbolMinMaxUnitNotes Differential peak-to-peak Input voltage VDIFF p-p 120- mV For high bit rate 40-For reduced bit rate Rx DC common mode voltageV CM 02.0V DC Specification AC Specification 3-3. eDP Signal Timing Specifications The VESA Display Port related AC specification is compliant with the VESA Display Port Standard.

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Signal Timing Specifications Table 4. TIMING TABLE This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications and specifications of eDP Tx/Rx for its proper operation Signal Timing Waveforms Condition : V CC =3.3V Low: 0.3VCC High: 0.7VCC Hsync Date Enable Vsync Date Enable t WH t HP t HFP t HBP t VP t WV t VBP t VFP t WHA t WVA ITEMSymbolMin.Typ.Max.UnitNote DCLKFrequency f CLK MHz Hsync Period t HP tCLK Width t WH Width-Active tw HA 1366 Vsync Period t VP tHP Width t WV 357 Width-Active tw VA 768 Data Enable Horizontal back porch t HBP tCLK Horizontal front porch t HFP 3248 Vertical back porch t VBP tHP Vertical front porch t VFP 235

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Color Input Data Reference The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input. Table 5. COLOR DATA REFERENCE Color Input Color Data RED MSB LSB GREEN MSB LSB BLUE MSB LSB R5 R4 R3 R2 R1 R0G5 G4 G3 G2 G1 G0B5 B4 B3 B2 B1 B0 Basic Color Black Red Green Blue Cyan Magenta Yellow White RED RED (00) RED (01) … ……… RED (62) RED (63) GREEN GREEN (00) GREEN (01) ……… GREEN (62) GREEN (63) BLUE BLUE (00) BLUE (01) … ……… BLUE (62) BLUE (63)

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Power Supply VCC eDP Display HPD from Sink Sink Aux CH Source Main Link Data LED on/off Signal LED_EN Dimming signal Of LED B/L PWM Power Supply VLED 10% 90% 3-7. Power Sequence Table 6. POWER SEQUENCE TABLE Black VideoVideo From SourceBlack Video Aux Channel Operational Idle or offValid Video DataIdle Link Training T10T10 T1T1 T2T2 T11T11 T3T3 T4T4 T7T7 T5T5 T6T6 T8T8 T9T9 T12T12 Enabled PWM 10% 90% T13T13 T14T14 T16T16 T 15 T18T18 T 17 Note) 1. Do not insert the mating cable when system turn on. 2. Valid Data have to meet “3-3. eDP Signal Timing Specifications” 3. Video Signal, LED_EN and PWM need to be on pull-down condition on invalid status. 4. LGD recommend the rising sequence of VLED after the Vcc and valid status of Video Signal turn on. Timing Required By Limits UnitsNotes MinMax T 10 Source0500ms- T 11 Source-10ms- T 12 Source500-ms T 13 Source0.510ms- T 14 Source0.510ms- T 15 Source10-ms- T 16 Source10-ms- T 17 Source0-ms- T 18 Source0-ms- Timing Required By Limits UnitsNotes MinMax T1T1 Source0.510ms- T2T2 Sink0200ms- T3T3 Sink0200ms- T4T4 Source--ms- T5T5 Source--ms- T6T6 Source--ms- T7T7 Sink050ms- T8T8 Source--ms LGD recommend Min 200ms T9T9 Source--ms-

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Optical Specification FIG. 1 Optical Characteristic Measurement Equipment and Method Table 9. OPTICAL CHARACTERISTICS Ta=25  C, Vcc=3.3V, f V =60Hz, f CLK = TBD, V LED = 12V, PWM Duty = 100% LCD Module Optical Stage(x,y) Pritchard 880 or equivalent 50cm Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in a dark environment at 25  C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of  and  equal to 0 . FIG. 1 presents additional information concerning the measurement equipment and method. ParameterSymbol Values UnitsNotes MinTypMax Contrast RatioCR Surface Luminance, whiteL WH Luminance Variation(13points)  WHITE Response TimeTr R + Tr D -3550ms4 Color Coordinates REDRX RY GREENGX GY BLUEBX BY WHITEWX WY Viewing Angle5 x axis, right(  =0  ) rr 85-degree x axis, left (  =180  ) ll 85-degree y axis, up (  =90  ) uu 85-degree y axis, down (  =270  ) dd 85-degree Gray Scale6 Color GamutC/G-45-%

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Note) 1. Contrast Ratio(CR) is defined mathematically as Surface Luminance with all white pixels Contrast Ratio = Surface Luminance with all black pixels 2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 1. L WH = Average(L 1,L 2, … L 5 ) 3. The variation in surface luminance, The panel total variation (  WHITE ) is determined by measuring L N at each test position 1 through 13 and then defined as followed numerical formula. For more information see FIG 2. Maximum(L 1,L 2, … L 13 )  WHITE = Minimum(L 1,L 2, … L 13 ) 4. Response time is the time required for the display to transition from white to black (rise time, Tr R ) and from black to white(Decay Time, Tr D ). For additional information see FIG Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG Gray scale specification * f V = 60Hz Gray LevelLuminance [%] (Typ) L00.13 L70.81 L L L L L L L

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 FIG. 4 Viewing angle FIG. 3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”. : ACTIVE AREA A : H/4 mm B : V/4 mm POINTS: 13 POINTS H,V Active Area H A B V mm FIG. 2 Luminance

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Mechanical Characteristics The contents provide general mechanical characteristics for the model LP133WH2. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Horizontal306.3±0.5 mm Vertical188.7±0.5 mm Depth3.0 mm (Max) Active Display Area Horizontal293.4 mm Vertical165.0 mm Weight275g (Max) Surface Treatment Glare treatment of the front Polarizer

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Note) Unit:[mm], General tolerance:  0.5mm AB CD A B C D

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Note) Unit:[mm], General tolerance:  0.5mm

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Reliability Environment test condition { Result Evaluation Criteria } There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. No.Test ItemConditions 1High temperature storage test Ta= 60  C, 240h 2Low temperature storage test Ta= -20  C, 240h 3High temperature operation test Ta= 50  C, 50%RH, 240h 4Low temperature operation test Ta= 0  C, 240h 5Vibration test (non-operating)Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min 3 axis, 1hour/axis 6Shock test (non-operating)Half sine wave, 180G, 2ms one shock of each six faces(I.e. run 180G 2ms for all six faces) 7Altitude operating storage / shipment 0 ~ 10,000 feet (3,048m) 24Hr 0 ~ 40,000 feet (12,192m) 24Hr

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / International Standards 7-1. Safety 7-2. Environment a) RoHS, Directive 2011/65/EU of the European Parliament and of the council of 8 June 2011 a) UL , Underwriters Laboratories Inc. Information Technology Equipment - Safety - Part 1 : General Requirements. b) CAN/CSA-C22.2 No , Canadian Standards Association. Information Technology Equipment - Safety - Part 1 : General Requirements. c) EN , European Committee for Electrotechnical Standardization (CENELEC). Information Technology Equipment - Safety - Part 1 : General Requirements. d) IEC , The International Electrotechnical Commission (IEC). Information Technology Equipment - Safety - Part 1 : General Requirements

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / Packing 8-1. Designation of Lot Mark a) Lot Mark ABCDEFGHIJKLM A,B,C : SIZE(INCH) D : YEAR E : MONTH F ~ M : SERIAL NO. Note 1. YEAR 2. MONTH B Nov Mark Month A Oct 6 Jun 7 Jul 8 Aug 9 Sep 4 Apr 5 May C321 DecMarFebJan b) Location of Lot Mark Serial No. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice Packing Form a) Package quantity in one box : TBD pcs b) Box Size : TBD Mark Year K 2020 F 2016 G 2017 H 2018 J 2019 D 2014 E 2015 CBA CT Code TBD

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength OPERATING PRECAUTIONS (1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage : V=± 200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference.

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly ELECTROSTATIC DISCHARGE CONTROL Strong light exposure causes degradation of polarizer and color filter PRECAUTIONS FOR STRONG LIGHT EXPOSURE 9-5. STORAGE (1) When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. Please carefully peel off the protection film without rubbing it against the polarizer. (3) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarizer after the protection film is peeled off. (4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane HANDLING PRECAUTIONS FOR PROTECTION FILM When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5  C and 35  C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 APPENDIX A. Enhanced Extended Display Identification Data (EEDID TM ) 1/3

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 APPENDIX A. Enhanced Extended Display Identification Data (EEDID TM ) 2/3

Product Specification LP133WH2 Liquid Crystal Display Ver. 0.1Mar. 30, / 26 APPENDIX A. Enhanced Extended Display Identification Data (EEDID TM ) 3/3