BlueROV Electrical Block Diagram Pressure Enclosure

Slides:

Advertisements

Similar presentations

Part 1: Introduction FRC Introduction  FRC 2907 since 2008  Each area of the robot has a team assigned  The Electronics team is headed this year.

Advertisements

Presents The Silver Family An Integrated Approach to Processors, Data Communication and Head End Integration.

Overview of New System Beta Team from Wilsonville 1425 Wilsonville Robotics – Code Xero 2550 Oregon City Robotics.

AA241x Spring 2015 Adrien Perkins H ARDWARE AND S OFTWARE O VERVIEW.

Simply easy! TM XUSL2E/4E light curtains Pilot light ? How to provide a signal to a pilot light or to a PLC input.

 Wireless, Web-Based Monitoring System  Alarm/Event Notifications by Text Message and or  VPN Connection for Fast Response to Alarms and Events.

BAE SYSTEMS PROPRIETARY – Internal Use Only Unpublished Work Copyright 2014 BAE Systems. All rights reserved. BAE Systems C2C SWAT Project Tutorial 2,

BAE SYSTEMS PROPRIETARY – Internal Use Only Unpublished Work Copyright 2014 BAE Systems. All rights reserved. BAE Systems C2C SWAT Project Tutorial 3,

INTRUSION ALARM TECHNOLOGY

Electrical Components.  This supplies all the power to the robot. It is a single 12 V battery. They are sealed to prevent battery acid from leaking.

FIELD EFFECT TRANSISTORS (FETs) Past Paper Questions and Answers.

Pi In The Sky Chris Stubbs. What’s in the HAB kit Balloon (keep this safe) Parachute PITS kit Raspberry Pi Model A (for flight) + SD + Camera Raspberry.

Hybrid Wind & Solar Generation Project

On/Off Temp Holiday Select Fan Air clean Operation Auto SwingRoom Temp Week Select SET/CLR Hour MIN Timer Program Set Fan Speed Jet Cool Cancel RESET E_Heater.

P-REV Initial PCB Michael Connaboy Stephen Schiffli Ram Hudiara Win Than Aung.

V-Series Panel Hardware, Installation & maintenance.

EV-EMCU Electric Vehicle - Economy Mode Control Unit Shauntice Diaz Chris Chadman Vanessa Baltacioglu Group 4.

Basic Stamp Free Pins These pins can be used by the operator for digital Inputs and Outputs Used Pins 0.

BOOT MODE 1 BOOT MODE 2 BIOS COMMUNICATION DEFAULT CONTROLLER INVERT RELAY OPERATION ENABLE COMM FAIL RELAY CONTROL RELAY OFF / ON COMM.

Wall-E Prototype I Team 1 Xin Jin

LSU 09/19/2013BalloonSat Development Board1 The BalloonSat Development Board Programming Unit, Lecture 1.

Hardware Overview Autopilot Control Board- Serves as common platform for other components and has autopilot code and flight plans Battery- Powers the.

NSGF 2000 PICO EVENT TIMER HERSTMONCEUX SLR STATION.

Airmar H2183 Heading Sensor

Team 6 DOODLE DRIVE Alexander Curtis Peachanok Lertkajornkitti | Jun Pan | Edward Kidarsa |

ECE 477 Final Presentation Team 12  Spring 2013 Xirong Ye Zongyang Zhu Chun Ta Huang Libo Dong.

BAE SYSTEMS PROPRIETARY – Internal Use Only Unpublished Work Copyright 2014 BAE Systems. All rights reserved. BAE Systems C2C SWAT Project - WF32 Shield.

Circuits, Systems, & the Arduino. Challenge: Make the bulb light up! -Make observations and explain why it has the setup it does? - What are the components.

Performed by: Aharon Yakov Hen Markovich Instructor: Boaz Mizrahi המעבדה למערכות ספרתיות מהירות High speed digital systems laboratory הטכניון - מכון טכנולוגי.

Pixhawk PX4 Flight Controller: Configuration for ELEV-8 V2

BAE SYSTEMS PROPRIETARY – Internal Use Only Unpublished Work Copyright 2014 BAE Systems. All rights reserved. BAE Systems C2C SWAT Project – WF32 Shield.

INTRODUCTION TO FBD - Function Block Diagram by ( LOGO ) Revision 2.

Front End Board (16 channels) Superlayer Cross Section Frontend Enclosure HV cap board HV cap Board Signals from chamber wires go to HV cap board to be.

Aerospace Digital Communication Instrument Senior Design Presentation.

Ethernet I/O Set-Up This presentation will step through a typical configuration of the CON-DVT-IOE. Intellect 1.5 is used for the software portion. NEXT.

New product introduction:

Ethernet I/O Set-Up This presentation will step through a typical configuration of the DVT CON-IOE. Intellect 1.0 is used for the software portion.

SUBMITTED BY LENIN C INTRODUCTION Railways - cheapest mode of transportation. Aims to avoid accidents. Using simple electronic components- automate.

Connecting the cRIO to the 12 V power source and your computer

ECE477 Senior Design Android street car Team 12 Libo Dong 1.

TCSP – Schematics Design. Major Components Freescale 9S12A64FCUE Microcontroller Etek EB-85A GPS Receiver Electronic Speed Controller HP Photosmart R707.

3DR Pixhawk Autopilot 3DR uBlox GPS with Compass Raspberry Pi 2 Model B Raspberry Pi Camera Board Ctrl / Data Ethernet Tether 6600 mAh 4s Lipo Battery.

Designing a Control System Sayande Adekoye College of North West London.

BlueROV Electrical Interconnect Block Diagram

Portable Power Station University of Wyoming Electrical and Computer Department EE Done By Mohammad S. Almoallem Mahmood S. Almoallem Advised.

Residential Security, Access Control, and Surveillance Copyright © 2005 Heathkit Company, Inc. All Rights Reserved Presentation 5 – The HAI Omni II Controller.

Copyright 2013 by openmake.cc Introduction to Multi-Pi Raspberry Pi pinhead plug-able.Raspberry Pi pinhead plug-able. Separate Communication port from.

BlueROV Electronics and Controls Documentation

Door Controller Device. 2 Door Controller Device (DCD) The DCD is the “Remote Brains” of the system. It is the controller device located at each access.

Relay Controller Device. 2 Relay Controller Device (RCD) If additional relays are needed beyond the two that are available on the DCD, then a RCD can.

BlueROV Electronics and Controls Documentation

DIGITAL MULTIMETER DMG

Solar Energy Generator: Design Rendering Description

Hardware, Installation & maintenance

Site Controller Unit and Trunk Interface Unit

BlueROV Electrical Block Diagram Pressure Enclosure

I-Station Hardware, Installation & maintenance

HV Battery Assembly.

Android Street Car Team 12 Zongyang Zhu ECE 477 Senior Design Project

Internet-of-Things (IoT)

BLOCK DIAGRAM: Micro controller.

Module 1 – Power Supply AMC APS-PBC-60

Schematic to Pictorial

3DR uBlox GPS with Compass Raspberry Pi Camera Board

Arduino and Grove LET’S START.

easYgen-3000XT Series Training

The BalloonSat Development Board

When we check output of R32 (MOTION_SENSE_HIGH) we are getting Low(0

Robot and Crickit HAT © Copyright 2019 by Dr. Elizabeth I. Horvath and Dr. Eva A. Horvath 1.

Presentation transcript:

20160229 BlueROV Electrical Block Diagram Pressure Enclosure BlueRoboticsPressure / Temp. Sensor 6600 mAh 4s Lipo Battery 14.8vdc XT90 XT90 I2C Expander 3DR uBlox GPS with Compass Compass 3DR Power Module Power 5 vdc I2C GPS GPS +14.8 vdc XT60 XT60 3DR Pixhawk Autopilot XT60 BatPwr In JST-XH (connect to aux. output - see Sht. 3) Pressure Enclosure Power 5 vdc 1.2A +14.8 vdc XT60 Buzzer Main ESC PWM Thruster Ctrl Raspberry Pi 2 Model B Raspberry Pi Camera Board JST-XH JST-XH Main Outputs See Sht. 3 ……6x….. Terminal Board Terminal Board +14.8 vdc Gnd Buzzer (Optional) Ctrl / Data Ethernet Tether Basic 30A ESC Basic 30A ESC ESCs ……6x….. Topside (Laptop) T200 Thruster T200 Thruster Thrusters ……6x….. 20160229 Sht 1 BlueROV-Block-Diagram-20160229.pptx

Pixhawk Overview Connect here for Raspberry Pi 5v power Connect ESCs Control Here Connect 3DR Power Module Pigtail Here Buzzer (Optional) 3DR uBlox GPS Connect I2C Expander Then connect uBlox Compass and BlueRobotics Depth Sensor to Expander Ref: http://copter.ardupilot.com/wiki/common-pixhawk-overview/ Sht 2

Pixhawk connector assignments Pwr Input (from module) Warning Buzzer (optional) Signal from GPS/Compass Connect I2c Expander which is connected to uBLOX compass and Bluerobotics depth/temp. sensor Thruster ESCs - PWM Rasp. PI +5v / - Gnd. Sht 3 Ref: http://copter.ardupilot.com/wiki/common-pixhawk-overview/

3DR UBlox GPS + Compass Module This page covers the installation of the 3DR UBlox GPS + Compass module. Pressure Sensor I2c Exp Ref: http://copter.ardupilot.com/wiki/common-installing-3dr-ublox-gps-compass-module/ Sht 4

Ref: http://copter.ardupilot.com/wiki/common-3dr-power-module/ 3DR Power Module This page explains how to set up the 3DR Power Module (PM) to measure battery voltage and current consumption. The information will also be useful for setting up other types of Power Module. To BlueROV Terminal Board +/Gnd XT60 Connector To Pixhawk Power Input Conn. Ref: http://copter.ardupilot.com/wiki/common-3dr-power-module/ Sht 5

I’ve got a few comments: 1. The “safety sw” is currently disabled in our recommended parameters. The buzzer is optional. (Removed Safety Sw. connection from sht 1 and 3. Added word (optional) to buzzer on sht 1 and 3 .) pfw 2. I would recommend supplying power to the Raspberry Pi via one of the auxiliary outputs (shown on page 3 of your slides) (updated shts 1 and 3 accordingly) pfw 3. If you are planning to use a pressure sensor for depth, you will need to use the I2C expander that comes with the PixHawk to connect both the pressure sensor and GPS/compass. (Slide 5) (updated shts 1 and 3 accordingly) pfw Please let us know if you have any other questions. -Rusty