Paint bottom first. Two coats of paint Paint the top last.

Slides:

Advertisements

Similar presentations

How to check close-to-the-line arrows F E D E R A T I O N I T N E R N A T I O N A L E D E T I R A L ' A R C a b TOP VIEW FRONT VIEW a b c d e c d e.

Advertisements

Equipment for Assembly Fluke Multimeter 115 True RMS Glue Ring Jig Flathead screwdriver 60 Watt desk lamp HIOS Cl 4000 Electric screw driver Anti-static.

AccuTec LLC 10/22 ® Barrel Pusher Patent Pending Proudly Made In The USA.

Drawing furniture using One Point Perspective

Training Guide. Exterior The exterior needs to be completed first.

Glenn Murcutt SRT 251 Construction and Structures Warehouse and Office complex scenario Stacy Ambelas

Put a drop of oil inside the wire holder caps – stops rust.

Sandblasted, repainted fender brackets. Mudflaps and rubber buttons to attach them.

Cobwebs and ladybugs. Pulling the gas tank and other parts.

My furgone watching. Wipe the frame clean Ready to remove the rust.

Trim Fwd Spar End Brackets July 6, H2-2, Horizontal Stab Rear Spar 7H1-2, Stab Full Rib Corner of Forward.

Mer/Sup. 2 & 3 Door Evaporator Coil Repositioning Procedure S. Starnes 7/11/03 1. Remove the 2 screws holding one end of the evaporator coil. (view shows.

ASSEMBLY INSTRUCTIONS. 2 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: SIDE CUTTING PLIERS PRY BAR 7/16” & 9/16” WRENCH 3/16” ALLEN WRENCH T-15 TORQUE.

Vent window installed. Install door frame side latch.

Ladybugs spending the Winter on the brake hub and inside the wheel rim.

Cleaning out the stable for the girls. Bathroom window – we have to leave the stained glass and sash and install the new window on the outside of them.

Hp LaserJet 9500 Color Printer Training. Toner cartridges (print cartridges) Open the front doors.

How to Construct a Paper Airplane. Start Small Plane: Tear.

The DB In-Line Pumpout Unit Easy-to-use control panel with one switch to run the unit. 15 AMP reset fuse. 115 AC External water pump and tank drain have.

Frank F. Hejazi Architect Façade Improvements. Existing Conditions 1st Floor Facing South.

REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.

Hi. I’m.99 and I understand you’re here to be restored. Welcome.

Cabin beading ends. Cracked cabin beading No rust to speak of.

Chapter 11, Section 3. Interior Installation Installing a curtain rod Mounting Venetian blinds Mounting a window shade Hanging a picture.

Outside the body shop. Ready for the ride home Finished doors.

1 FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS PART NUMBER

Equipment and Tool Institute June 18, Challenger Body Structure Diane Coopmans, Body Structures Engineering.

The DUCTZ Experience. A Brief Overview of how DUCTZ Cleans a Heating and Cooling System.

Installation of Gil’s Fuel Box By Albert “ARAMP1” Rampone.

By: Joe M. Searcy Tools Needed  Small Flat-Tip Screwdriver (Taped up with masking tape)  Socket set (or nut drivers), sizes  ¼”

Garment Dust Covers For Textile Storage. Supplies You will need: Pre-washed cotton sheeting Cotton thread Cotton twill Sewing machine or needle.

Using Stress Analyzer for Tensile Testing © 2012 Project Lead The Way, Inc.Principles Of Engineering.

DRILL September 15, 2009 Name three drafting tools used in this class.

Auto shop safety Safety around the shop. Safety Which characteristic is essential for the professional auto technician? Responsible attitude Knowledge.

LOOKING GOOD. WHY TO KEEP A CLEAN CAR  Regular care and cleaning will prolong vehicle life by...  Preventing rust  It will give you a chance to notice.

Motorcycle gas tank rust removal & sealing Notes: 1.These are suggested instructions 2.Only applicable to steel gas tanks 3.Sealer won’t work on plastic.

Interior Painting How to paint like a pro.. Step 1: Preparation Remove as many items from room as possible Cover any remaining furniture & floors Remove.

Presented by: Joseph Coyle PROJECT 1- CAR WASH 12/7/11

MicroTouch Touchscreen Integration Tips and Techniques MicroTouch On the Move Paul Hatin & Mark Roberts.

How to Build a Divider Wall By Charysse Roberson.

Tools you will need #8 Torx driver #10 Torx driver Standard Phillips screwdriver Small (jewelers)Phillips screwdriver Small standard screwdriver.

Is not a crane Is not a jack or mechanical ladder Lifts are engineered to hoist and support vehicles….nothing else!  Before using lift make sure it.

Seeing Things Making Kaleidoscope Mirrors Long narrow glass mirrors work best but are more difficult to work with than plastic mirrors. If the back is.

The Body and Health 3 Parts of the Body: The Head.

HOW TO WASH A CAR PRESENTED BY: Daniel Leppke Project 1- Car Wash 10/9/12.

XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.

Remove 4 Phillips screws that hold tape drive cover (2 on each side) Phillips screws.

SIZE - Top SERVER ROOM Designed by – openbox |

How to detail your car  Vacuum cleaner  Variety of rags  Various sizes of smell brushes  Plastic spray bottles TOOLS OF TRADE.

WELCOME TO GOLD COAST REGION’S CONCOURS UNIVERSITY & CONCOURS PREPARATION SCHOOL 2016.

Forging new generations of engineers. USING THE STRESS ANALYSER FOR TENSILE TESTING.

10 Simple Tips to Take care of your Car & extend Its Service Life.

RELEASING PROTECTOR OF MOULDING, TRANSFER AND DECAL

Assembly Instructions:

2007 National Food Science CDE

Testing Apparatus Construction

Presented by: Jacob Thurston Project 1 - How to Wash a Car

Project 1 Car Wash.

Presented by: Cristian Davis Project 1 how to wash a car

Most Effective Methods to Clean the Dirty Airflow Mass Sensor.

Top Tips to Help You Maintain Your Dishwasher Properly

Using Stress Analyzer for Tensile Testing

How to Wash a Car Presented by: Norma A. Payan Poject 1 – Car Wash

Parts of the Body: The Head

Bulk Head (1) (1st Suspension Connection)

Charging without contact

Surface area and volume: Surface area of a cuboid

Single-Deploy Launch Checklist

Remove all labels from supplies and box

Presentation transcript:

Paint bottom first

Two coats of paint

Paint the top last

Plastic tool used on window rubbers

Free the weatherstipping

Simon the inspector checking things out

Are these the backrests?

Windshield removed

No rusty edges!

Not even on the inside!

Front view

Deliver to DenWay Auto Body in Bayfield

Upper and lower tailgates

Looking up todays date

Both doors

Back end, right side

Back end, left side

Fuel rod bracket

Fuel control

Tape inside signal hole

Tape over holes

Tape over turn signal hole

Left floor area prepared to paint

Treat with Rust Mort

Rust cleaned and treated

Dirty engine bay

Side view of the engine bay

Dirt and gravel

Engine cleaner – power wash

Remove wiring protectors

After the wash