Wireless Rash Driving Detection. Introduction Wireless Rash Driving Detection  To detect rash driving on highways and to alert.

Slides:



Advertisements
Similar presentations
Edited by Mandar More Technical Manager, Ninad`s Research lab Ninad243.weebly.com MODERN OFFICE MANAGEMENT TOOL FOR SELECTIVE DATA.
Advertisements

SOLAR CELL PARAMETERS MEASUREMENT
SUBMITTED BY LENIN C INTRODUCTION Railways - cheapest mode of transportation. Aims to avoid accidents. Using simple electronic components- automate.
BLDC Motor Speed Control with RPM Display. Introduction BLDC Motor Speed Control with RPM Display  The main objective of this.
Arduino Based DC Motor Speed Control
SUBMITTED BY EDGEFX TEAM PORTABLE CODED WIRELESS MESSAGE COMMUNICATION BETWEEN TWO PARTIES SECRETLY WITH LCD DISPLAY.
ARM CORTEX (STM32) BASED MOTOR SPEED CONTROL SUBMITTED BY EDGEFX TEAM.
Arduino based Automatic Temperature Controlled Fan Speed Regulator.
PORTABLE PROGRAMMABLE MEDICATION REMINDER
ENERGY METER TO INDICATE BILLING IN RUPEES FOR LOAD WISE OR DAY WISE
SENSING SOIL MOISTURE CONTENT AUTOMATIC IRRIGATION SYSTEM
RASH DRIVING WARNING SYSTEM FOR HIGHWAY POLICE
Parking Availability Indication System
UPFC, UNIFIED POWER FACTOR CONTROL
ARDUINO BASED UNDERGROUND CABLE FAULT DETECTION
SUBMITTED BY EDGEFX TEAM
AUTOMATIC EMERGENCY LIGHT WITH LED
SPEED CHECKER TO DETECT RASH DRIVING ON HIGHWAYS
VEHICLE MOVEMENT SENSED LED STREET LIGHT WITH IDLE TIME DIMMING
PROGRAMMABLE AC POWER CONTROL
Project Title DYNAMICALLY CHANGING SIGNAL LIGHT TIME ALLOTMENT IN STREET JUNCTIONS BASED ON TRAFFIC DENSITY Under the Guidance of Submitted by.
PIC CONTROLLED DYNAMIC TIME BASED CITY TRAFFIC SIGNAL
WIRELEES RASH DRIVING DETECTION
UP AND DOWN CONTROLLED SPEED OF DC MOTOR IN EMBEDDED SYSTEM
MULTIPLE SENSOR DATA ACQUISITION
MEASURING SOLAR PHOTOVOLTAIC POWER
PORTABLE PROGRAMMABLE MEDICATION REMINDER
Medication Reminder using PIC Microcontroller
SUBMITTED BY EDGEFX TEAM
SUBMITTED BY EDGEFX TEAM
ABSTRACT The outline of the project is Cycle stealing, as a method to remove whole cycle to control AC power the concept of achieving the cycle stealing.
BURGLAR ALARM ON WINDOW GLASS BREAKING
AUTO MAINS DISCONNECTING DC POWER SUPPLY
ARDUINO BASED AUTOMATIC TEMPERATURE BASED FAN SPEED CONTROLLER
Home automation using Arduino & ‘PIR sensor’
FACTS BY TSR, FLEXIBLE AC TRANSMISSION
PC CONTROLLED SCROLLING MESSAGE DISPLAY FOR COLLEGE NOTICE BOARD
SUBMITTED BY EDGEFX TEAM
AUTO POWER SUPPLY CONTROL FROM 4 DIFFERENT SOURCES: SOLAR, MAINS, GENERATOR & INVERTOR TO ENSURE NO BREAK POWER.
AUTOMATIC IRRIGATION SYSTEM ON SENSING SOIL MOISTURE CONTENT
RFID CONCEPT BASED CAR PARKING SYSTEM
Arduino BASED RFID Device Access
AUTO TRAIN SUBMITTED BY.
Project Title EVM IN 8051 Under the Guidance of Submitted by.
PRE-STAMPEDE MONITERING AND ALARM SYSTEM
3 PHASE SEQUENCE CHECKER BY LED INDICATION
SUBMITTED BY EDGEFX TEAM
ABSTRACT The microcontroller receives the Infrared Signal from the TV remote, the code of which is identified by the IR receiver depending on which it.
SUBMITTED BY EDGEFX TEAM
CONTROLLING AC power BY PROGRAMMING
DENSITY BASED TRAFFIC LIGHT TIMING CONTROL
SUBMITTED BY EDGEFX TEAM
MAINS OPERATED LED LIGHT IN STRING
Under the Guidance of Submitted by
9 LEVEL OVERHEAD WATER TANK NDICATOR
SMART CARD ENABLED EMPLOYEE IDENTIFICATION FOR SECURITY PURPOSE
FASTEST FINGER PRESS QUIZ BUZZER
QUIZ COMPETITION SENSOR FOR FASTEST FINGER PRESS
Remote Override of Traffic Signal in Emergency
ARDUINO DC MOTR SPEED CTL
Project Title EVM IN PIC Under the Guidance of Submitted by.
SUBMITTED BY EDGEFX TEAM
PWM BASED SPEED CONTROL FOR DC MOTOR
POWER SAVING LED LIGHT REPLACING CONVENTIONAL LAMPS
CAR PARKING MANAGEMENT BY RFID
Under the Guidance of Submitted by
TWO PHASE BLDC MOTOR SPEED CONTROL USING FUZZY LOGIC CONTROL
IOT based Home Automation Over the Cloud
Under the Guidance of Submitted by
A PROJECT ON PASSWORD BASED CONTROL SYSTEM. A PROJECT ON PASSWORD BASED CONTROL SYSTEM.
Presentation transcript:

Wireless Rash Driving Detection

Introduction Wireless Rash Driving Detection  To detect rash driving on highways and to alert the traffic authorities wirelessly the speed details and any speed violation. Accidents due to rash driving on highways are on the rise and people are losing their lives because of others mistakes. In the present system, to detect rash driving the police has to use a handheld radar gun and then aim at the vehicle to record its speed.  If the speed of the vehicle exceeds the speed limit, nearest police station is informed to stop the speeding vehicle. This is an ineffective process as after detecting one has to inform the same and a lot of time is wasted.

Wireless Rash Driving Detection Block Diagram Of Transmitter

Wireless Rash Driving Detection Block Diagram Of Receiver

Wireless Rash Driving Detection Hardware Requirements Transformer Diodes Capacitors Resistors LEDs IR photodiode Transistor LCD Buzzer Relay Lamp 8051 series Microcontroller 2.4GHz Tx/Rx pair

Wireless Rash Driving Detection Power Supply

Wireless Rash Driving Detection Description Of Power Supply  The circuit uses standard power supply comprising of a step-down transformer from 230v to 12v and 4 diodes forming a Bridge Rectifier that delivers pulsating dc which is then filtered by an electrolytic capacitor of about 470microf to 100microF.  The filtered dc being un regulated IC LM7805 is used to get 5v constant at its pin no 3 irrespective of input dc varying from 9v to 14v.  The regulated 5volts dc is further filtered by a small electrolytic capacitor of 10 micro f for any noise so generated by the circuit.  One LED is connected of this 5v point in series with a resistor of 330ohms to the ground i.e. negative voltage to indicate 5v power supply availability.

Wireless Rash Driving Detection Internal Structure Of a Microcontroller - AT89S52/51

Wireless Rash Driving Detection Photo Diode  A photodiode is a type of photo detector capable of converting light into either current or voltage, depending upon the mode of operation.  Photodiodes are similar to regular semiconductor diodes except that they may be either exposed (to detect vacuum UV or X-rays) or packaged with a window or optical fibre connection to allow light to reach the sensitive part of the device.

Wireless Rash Driving Detection Liquid Crystal Display (LCD)  Most common LCDs connected to the microcontrollers are 16x2 and 20x2 displays.  This means 16 characters per line by 2 lines and 20 characters per line by 2 lines, respectively.  The standard is referred to as HD44780U, which refers to the controller chip which receives data from an external source (and communicates directly with the LCD.

Wireless Rash Driving Detection LCD Background  If an 8-bit data bus is used the LCD will require 11 data lines (3 control lines plus the 8 lines for the data bus).  The three control lines are referred to as EN, RS, and RW.  EN=Enable (used to tell the LCD that you are sending it data).  RS=Register Select (When RS is low (0), data is treated as a command). (When RS is High(1), data being sent is text data ).  R/W=Read/Write (When RW is low (0), the data written to the LCD). (When RW is High(1), the data reading to the LCD).

Wireless Rash Driving Detection Light Emitting Diode (LED)  LEDs are semiconductor devices are made out of silicon. When current passes through the LED, it emits photons as a by product.  Normal light bulbs produce light by heating a metal filament until its white hot.  LEDs present many advantages over traditional light sources including lower energy consumption, longer lifetime, improved robustness, smaller size and faster switching

Wireless Rash Driving Detection Buzzer  Piezo Buzzer: This buzzer is an piezo type audio signalling device, which has a piezo element and a oscillating circuit inside which oscillates the piezo brass base plate, which when given voltage difference produces sound of a predefined frequency.  Features: These high reliability piezo buzzers are applicable to general electronics equipment. Compact, pin terminal type Piezo buzzer with 4 KHz output. Pin type terminal construction enables direct mounting onto printed circuit boards.

Wireless Rash Driving Detection Working Principle  IR sensors to detect the presence of a vehicle.  A set point consists of a pair of sensors comprising of an IR transmitter and an IR receiver, each of which are installed on either sides of the road.  Whenever IR rays are interrupted by a vehicle during first sensor the count up timer is started.  When the other IR sensor senses the presence of vehicle, the count up timer is stopped.  The speed limit set by the device is kept at the very location depending upon the traffic.

Wireless Rash Driving Detection Working Principle  The time taken by the vehicle to travel from one set point to the other is calculated by a microcontroller program.  Based on that time it then calculates the speed.  The Seven segment display is used to display the speed of the vehicle.Seven segment display  If the vehicle crosses the speed limit, a buzzer sounds alerting the police both at the location and wirelessly at the control room.  The microcontroller is used to monitor the all control operations needed.

Wireless Rash Driving Detection Advantage:  They reduce the risk of accidents.  It is easy to implement.  It reduces the effort of many men.

Wireless Rash Driving Detection Disadvantages:  Sometimes the circuit got failure and causes various problems

Wireless Rash Driving Detection Applications  It uses in highways to avert accidents.  It alert traffic authorities about the speed of vehicle.

Wireless Rash Driving Detection Conclusion  The speed checker for highways‖is an emerging field and there is a huge scope for research and development. Wireless Rash Driving Detection can be further advanced by using a CCTV camera in the circuit. Whenever any vehicle crosses speed limit, camera captures the image of number plate and through transport database finds the address of the owner and sends fine.Wireless Rash Driving Detection