5-Axis Vertical Machining Center MAM72-63V
1. Improve existing model 4. Continue to offer flexibility with existing horizontal and previous model 3. Offer enhanced proven quality to existing applications 2. Target existing users and generate new business Development Concepts
Item New MAM72-63VMAM72-63V Rapid traverse rate 60 m/min Auto. grease as standard 50 m/min Auto. grease as standard Axis stroke760/ 845/ 660mm760/ 845/ 610mm Max. Work Size (STD) (non APC) D720 X H kg Max. Work Size (OP) (PC2) D630 X H450 mm D800 with restriction D630 X H450 mm 350kg Spindle12k Grease 20k Auto. grease (OP) 30k Oil air(OP) 12k Grease 20k Oil air (OP) 30k Oil air (OP) Specification Changes
Item New MAM72-63VMAM72-63V A/C Axis (STD ) Worm gear A/C Axis FeedrateA: 25min -1 C: 50min -1 A: 25min -1 C: 50min -1 A Axis Travel (PC2) +30 ~ -120deg+10 ~ -110deg A Axis Travel (non APC) +120 ~ -120deg+110 ~ -110deg No. of ATC toolsStandard: 51 toolsStandard: 30 tools Thermal displacement compensation Spindle & Feed axis :standard Spindle: option NC G-Tech 840DI/ 30 i Specification Changes
APC New MAM72-63VMAM72-63V APC ・ 2PC ・ PC6 (Floor pallet system) ・ PC18 (Tower pallet system) ・ PC17 (Liner pallet system) ・ PC2 ・ PC6 ・ PC17 ATC 51T (Drum type) ・ 120 ~ 240T(Matrix) ・ 120 ~ 320T(New Matrix) ・ 360 ~ 520T(New Matrix) ・ 40T (Chain type) ・ 80T (Chain type) ・ 120 ~ 240T(Matrix) Main Options
Guarding
1.Tool magazine developed instead of the chain type tool magazine 2.No. of tools: 51 3.Fixed address system 4.Servo motor drive 1.Minimized noise 2.Minimized vibration 5.Index speed increased (Compared with that of the chain type 51-too magazine) 1.Longest index time: 3.2 sec. (7.5 sec.) 2.Adjacent pot-tool index time: 0.4 sec. (1.9 sec.) ATC
New Options
H2 = 320mm (A axis -120 ~ +30°) H2 = 350mm (A axis -107 ~ +10°) H2 = 450mm (A axis -10 ~ +10°) H450mm H2* Work Capacity D800mm D630mm D800mm D630mm
1.Spindle thermal displacement compensation function and Feed-axis thermal displacement compensation function to be used at the same time 2.Both thermal displacement caused by spindle heat and that caused by feed-axis drive to be compensated 3.Spindle thermal displacement compensation function (Temperature monitor type) 1.Temperature sensor to be fixed on the spindle bearing 2.Spindle temperature to be monitored & Thermal displacement caused by spindle heat to be compensated 4.Feed-axis thermal displacement compensation system 1.Temperature sensor to be fixed on the feed-axis ball-screw 2.Ball-screw temperature to be monitored & Thermal displacement caused by feed-axis drive to be compensated THERMAL MEISTER New Features
THERMAL MEISTER New Features
Cleaning of the A-axis base ( picture: New MAM72-63V ) coolant Operator side Coolant and Chip Management
It is possible to separate the flange from the unclamp cylinder without removing the spindle motor. Exchange Time: 20 hours ⇒ 10 hours Spindle Unclamp cylinder section Improvement of Service
Target Markets Prototype Aerospace Mold & die Medical Flexibility
Thank you