Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved.Rev 5058-CO900E PUBLIC INFORMATION Guardmaster ® 440C-CR30 Software Configurable Safety Relay Firmware Release 10

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 2 Agenda Guardmaster 440C-CR30 Overview What’s New in Firmware Release 10 Resources What’s New – Add-on Profile 2.01

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 3 What’s New in Firmware Release 10 Logic Editor Enhancements  Numerous usability and logic editor enhancements in Guardmaster 440C-CR30 safety relay firmware 10, Connected Component Workbench Release 9:  Key Function Block Changes: Three new and one enhanced function blocks in the 440C-CR30 editor will give us the flexibility to solve these applications: Fault & Reset Required Annunciation Mode SelectionLock ControlMute Enhancements

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 4  Numerous enhancements to the Muting function block: Override Output: Only enable local conveyor to clear light curtain, not the whole machine What’s New in Firmware Release 10 Mute Function Block Enhancements Mute Enable: New interlock to only allow muting when appropriate (i.e. conveyor on) Mute Fault Reset: Enable a manual monitored reset after a muting fault

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 5  New Mode Selection function block’s main function is to energize one of it’s up to three outputs when the associated input goes active: What’s New in Firmware Release 10 Mode Selection Function Block Mode Selection Operation: Only one Input and associated Output may be energized at a time: A fault is generated when a ‘no input active’ condition exists for more than 250ms A fault is generated when a ‘multiple input active’ condition exists for more than 250ms Application Examples: Safely switching between: Operation and Maintenance Modes Active field sets on an area scanner 2-Position Configuration: 3-Position Configuration:

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 6  New Lock Control Function Block to dramatically simplify guard locking applications: What’s New in Firmware Release 10 Lock Control Function Block Lock Control: Ability to issue an unlock request to a safety gate with guard locking Monitors for: Hazard Stopped and/or De-energized + Optional Time-Delay Up to 50 minute time Delay can be configured

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 7 What’s New in Firmware Release 10 Example Application – 442G MAB Integration  New Lock Control Function block dramatically simplifies locking applications Safety Function 1 Safety Function 2 Safety Function 1: Safety-related emergency stop function: following an unexpected opening of Guard Lock (SMF 2), safe torque off (STO, SOF 1) is initiated. Safety Function 2: No deactivation of guard locking (SOF 2 O1) until an application specific time delay (SMF 2 Stop Time) after STO (SMF 4 Hazard Feedback).

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 8  New Status Blocks allow you to monitor a variety of status conditions and drive and output to a stack light to inform the operator/service personnel: What’s New in Firmware Release 10 Status Input and Output Function Blocks Function Block Fault Monitoring: Set up the Status block to monitor any combination of function block’s for a faulted status and use that to drive a status indicator Reset Required Monitoring: Set up the Status block to monitor any combination of function block’s waiting for a reset status and use that to drive a status indicator

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 9 What’s New in Firmware Release 10 Single Input AND with Restart  AND with Restart now supports single input:  Now it is easy to set up your Emergency Stop string as Manual Reset while your Safety Gate string is Automatic Reset within the same zone.

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 10 What’s New in Firmware Release 10 Feedback Reuse on multiple Safety Output Functions  A single feedback can now be used on multiple Safety Output Functions:  Now it is easy to ensure the Immediate OFF outputs can not be reset by the operator before the time-delayed OFF outputs time hasn’t expired.

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 11 What’s New in Firmware Release 10 Usability Enhancement: Better Tooltips  Now when an instruction faults the tooltip will appear the first time until acknowledged:  Previously you would have to hoover over the instruction, users were not aware that detailed information was available.

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 12 What’s New in Firmware Release 10 Usability Enhancement: Better Tooltips  Now when an instruction faults the tooltip will appear the first time until acknowledged:  Previously you would have to hoover over the instruction, users were not aware that detailed information was available.

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 440C-CR30-STARTERPACK1 13  Complete bundle to build your own functional demo  Available for sales in all sales orgs at 1,300USD list price  Cat. No. 440C-CR30-STARTERPACK1  PGC 32F – same as for 440C-CR30  Stocked item  To support your promotional events contact the Product Manager:  Brad Prosak:  For higher quantity request >20 we consider a lead time of days Available Now!

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Content 14  Includes 440C-CR30, safety switches, 700-HPS safety relays and a mounting plate  Just some wires and screws away from your own functional demo RefOrder numberQtyDescription 1800F-1YMQ3V1E-Stop Assembled Station 2440N-Z21SS3PA1SensaGuard LiteLatch PS VAC1120/240VAC to 24VDC Power Supply 4700-HN1232Mini 8-Pin Screw Terminal Socket, 700-HPS2Z242Safety Control Relay, 700-HP 5889D-F4AC-21DC Micro (M12) PVC Cable IQ4OB414-ch Digital Input/Output 7440C-CR30-22BBB1CR30 configurable safety relay 8598-PP Mounting Plate 9 1 USB programming cable

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Build your own demo 15  All information in one place:  Functional description  Schematic  BOM and  Quick start guide for configuration

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New Add-on Profile 2.01 for Studio 5000 Logix Designer Software

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 17 New Version 2.01 Add-on Profile AOP with Integrated Editor for Guardmaster 440C-CR30 Safety Relays  Premier Integration with Logix control systems:  Add-on Profile v2.01 for Studio 5000 Logix Designer software will contain fully functional Logic editor for the Guardmaster 440C-CR30 safety relay.  Single software/project for configuring and monitoring Logix controller and Guardmaster 440C-CR30 safety relays.

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 18  System Integration with Logix controllers  with AOP version 2.01: Design Software Control Level Device Level Information Level 440C-CR30 HMI Controller What’s New in Firmware Release 10 Logix Controller Integration with Guardmaster 440C-CR30 Safety Relay  Design Software : Add-on Profile in Studio 5000 v20 or later  Controller : Logix5000 controller, firmware revision 20 or later  HMI : PanelView Plus (direct connection with EDS Parameter browse)  440C-CR30 : Revision 9 firmware and 440C-ENET plug-in Single Software Package!

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Working with 440C-CR30 Add-on Profile Apply Offline Guardmaster 440C-CR30 Safety Relay Configuration Download Project From Workstation to Controller. 3. Select Logic Configuration tab. 4. Push download if necessary. Download begins. 2. Open device profile. Configuration stored in project ACD and downloaded to Controller DownloadProject

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Working with 440C-CR30 Add-on Profile Replace a Guardmaster 440C-CR30 Safety Relay Connect Project From Workstation to Controller. 3. Select Logic Configuration tab. 4. Push download. Download begins. 2. Open device profile. Configuration stored in project ACD and downloaded to Controller ConnectProject

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Overview Guardmaster 440C-CR30 Safety Relay

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Why choose Guardmaster 440C-CR30 Software Configurable Safety Relay Safety made Simple & Flexible Supports four to nine dual channel input circuits and up to five safety output zones Flexible configuration allows you to re-engineer and rapidly integrate application without having to incur high costs of rewiring Innovative safety logic editor reduces the friction involved in setting up a safety system by minimizing manual input for a “best-in-class” configuration experience Optimize Panel Space 22 Safety I/O in a compact 110mm wide housing Expand by up to 16 standard I/O using front mounted plug-in slots that allow you to maintain the 110mm horizontal footprint Part of the Connected Components Workbench™ Bundle Preferred compatibility within the bundle Reduced supply chain costs One software supports Guardmaster 440C-CR30, Micro800 controllers, PowerFlex ® drives, Kinetix™ 3 servo drives and PanelView™ Component terminals Safety & Productivity Embedded serial port for direct diagnostic communications to PanelView Component terminals or Micro800™ controllers 16 user configured status LEDs allow you to tailor indication to best suit your application

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Anatomy Block-style Safety Relay – 22 points Configurable LED Indicators RS232 Serial Port (non-isolated) USB Programming Port Verification ID Display Switch Two Plug-in Slots DIN Rail or Panel Mount 2 Single-Wire Safety or Safety N.C. Inputs 2 Single-Wire Safety or Safety Outputs 10 Dedicated N.C. Safety Inputs 6 Configurable Safety Terminals (N.C. Inputs, N.O. Inputs, Test Sources, or Outputs) 2 Safety Outputs

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Key Features  Easy to Use:  Innovative rapid configuration editor  2080 Plug-in support :  Expansion of standard I/O  Comms for Diagnostics  EtherNet/IP to Logix  Serial to Micro800 or PanelView Component  Single Wire Safety support:  A single wire to expand safety I/O Reset Muting Sensors Feedback Monitoring Keeps safety simple, separate and flexible

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Easy to Use 25 Assigned safety function via Drag ’n’ Drop Ease of configuration – No previous programming skills required DONE! Configure Safety Function Validate and Verify Configure Device Logic configured with Simple Drag and Drop Function Block Editor Checklist to walk through validation and verification process Configured in CCW

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Key Features Auto Configuration of I/O based on Function block assignment  Easy to Use :  Rapid configuration with pre-configured function blocks 1. 2.

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Easy to Use Diagnostic tooltips for application troubleshooting  Easy to Use : Online Monitoring Color-coded online monitoring helps troubleshoot code Diagnostic tooltips provide natural language fault descriptions

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Single Wire Safety Support  Supports Single Wire Safety for easy integration/expansion with GSR relays : Add Safety Relay Outputs Add multiple dry contact outputs by utilizing GSR EM (Expansion module) while only consuming a single safety output configured for Single-Wire Safety Connect Upstream GSR Relays Expand inputs and functionality using GSR relays by connection through Single-Wire Safety

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Single Wire Safety Support 29 SWS Zone 1... Up to 10 off a single SWS Output  Supports Single Wire Safety for easy interlocking of CR30s : Global E-Stop with Cascaded SWS Cascade a Single Wire Safety signal to up to ten CR30s to create a global E-Stop without the need of a complicated safety network 30m max

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay 2080 Plug in Support Expansion I/O with no impact to panel footprint  2080-IQ4OB4 plug-in for expansion I/O : Reset Feedback Monitoring Mute Sensors Standard Input Expansion Use standard inputs for standard signals such as circuit resets, feedback monitoring or mute sensors Standard Diagnostics Land auxiliary contacts of series wired safety devices and share with PanelView Component terminals Use standard outputs to drive indicator LEDs or send gate unlock commands

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Direct Serial Connection to PanelView Component or Micro800  Share diagnostics with HMI or controller : Direct PanelView Component Connectivity Embedded Serial Port on CR30 can be directly connected to a PanelView Component terminal Direct Micro800 Controller Connectivity Embedded Serial Port on CR30 can be directly connected to a Micro800 controller for Diagnostics

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Resources 32 Category DescriptionFile names/hyperlink Documentation Guardmaster 440C-CR30 safety relay Product Profile pp001_-en-p.pdf Guardmaster 440C-CR30 safety relay User Manual um001_-en-e.pdf Guardmaster 440C-CR30 safety relay Wiring Diagrams wd001_-en-p.pdf Guardmaster 440C-CR30 safety relay Product Catalog /print.html Guardmaster 440C-CR30 safety relay Quick Start qs001_-en-p.pdf Guardmaster 440C-CR30 safety relay Web Page 440C-CR30 Guardmaster 440C-CR30 safety relay Virtual Brochure Sample Code Guardmaster 440C-CR30 to Micro820 to EtherNet/IP Application Code Software Connected Components Workbench Web page components/tools/workbench.pagewww.rockwellautomation.com/products-technologies/connected- components/tools/workbench.page Logix Designer Add-on Profile Firmware Guardmaster 440C-CR30 safety relay firmware Catalog DescriptionSupplementary Documents 440C-CR30-22BBB Guardmaster 440C-CR30 software configured safety relay, PLe SIL 3, 22 Safety I/O, embedded serial port, USB programming port, 2 Plug-in Slots, 24.0V DC Configure in ProposalWorks Photo 2D Dimensional Drawing (DXF) 3D STEP Model (STP) 440C-ENET Guardmaster Ethernet Plug-in module, slot 1 only Photo 2D Dimensional Drawing (DXF) 3D STEP Model (STP)

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Guardmaster 440C-CR30 Safety Relay Resources 33 Category DescriptionFile names/hyperlink Safety Function Cable Pull Switch with a Configurable Safety Relay at134_-en-p.pdf Emergency Stop with a Configurable Safety Relay at132_-en-p.pdf Door-Monitoring Interlock Switch with a Configurable Safety Relay at133_-en-p.pdf Light Curtain with Muting (Two Sensor L-Type) and 440C-CR30 at136_-en-p.pdf

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New Firmware Release 9.004

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 35  Four new function block features available with Guardmaster 440C-CR30 safety relay firmware Compatible with:  Connected Components Workbench™ software R8.01  Studio 5000 Logix Designer™ Add-on Profile 2.01 (coming September 2015)  These new features dramatically increase the flexibility of the Guardmaster 440C-CR30 safety relay logic editor.  Output Loop  Nested Logic  RS Flip Flop  Invert Function Block Inputs/Outputs Invert I/O State Nested Logic RS Flip Flop Output Loop What’s New in Firmware Release 9 Four New Function Block Features

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 36  The new Output Loop function block allows the logical state of a Safety Output Function to be monitored as an input condition.  This feature allows you to build more complicated logic circuits within the Guardmaster 440C-CR30 safety relay logic editor. What’s New in Firmware Release 9 New Output Loop Safety Monitoring Function

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 37  The new Nesting capability allows you to use the output condition of a Logic Level function block as an input condition of a Logic Level function block on the same Logic Level.  This feature allows you to build more complicated logic circuits within the Guardmaster 440C-CR30 safety relay logic editor. What’s New in Firmware Release 9 New Nesting Logic Level Function Blocks Feature

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 38  The new RS Flip Flop logic level function block allows you latch a state enabling sequential logic.  This feature allows sequential logic needed for such functions as a single-stroke press. What’s New in Firmware Release 9 New RS Flip Flop Logic Level Function Block

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 39  The new Invert/Revert feature for Logic Level function block inputs and outputs allows you to use the inverse state as the valid condition for the function block.  This feature allows you to conserve logic level function blocks by eliminating the need to use a logic level NOT function block. What’s New in Firmware Release 9 New Invert Logic Level Function block Inputs and Outputs Feature

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 40  System Integration with Logix controllers  with AOP version 2.00 (Coming in September 2015) Design Software Control Level Device Level Information Level 440C-CR30 HMI Controller What’s New in Firmware Release 9 440C-ENET: Supported Topologies  Design Software : Add-on Profile in Studio 5k v20 or later  Controller : Logix5000 controller, firmware revision 20 or later  HMI : PanelView Plus (No direct connection between 440C-CR30 and PVP at launch)  440C-CR30 : Revision 8 or later firmware and 440C-ENET plug-in Single Software Package!

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New Release 8 – March 2015

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 8 42  Upgrade project to latest version to add features.  Upgrade version 6 or 7 projects to the latest version 8  Right-click on 440C-CR30 in Project Organizer to Upgrade Project Upgrade Feature Firmware upgrade of 440C-CR30 Safety Relay still required. Get the latest firmware:

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 8 43  New Standard Signal Safety Monitoring Function.  Allows you to easily use standard rated signals from plug-ins or the communication network in your application logic Standard Signal Safety Monitoring Function

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 8 44  New publication of common Guardmaster 440C-CR30 safety relay applications:  Application description  Schematic  440C-CR30 configuration  BOM Guardmaster 440C-CR30 Wiring Diagrams wd001_-en-p.pdf

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 45  Ethernet allows you to:  Configure and Monitor 440C-CR30 from Studio 5000 Logix Designer™ or Connected Components Workbench software  Troubleshoot 440C-CR30 safety system on HMI or in automation controller with diagnostic information shared over EtherNet/IP  Share standard Control signals between automation controller and 440C-CR30 safety relay (resets, feedback, etc.) 440C-ENET Plug-in What’s New in Release 8 440C-ENET Ethernet Plug-in for Guardmaster 440C-CR30 Safety Relay

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 46 What’s New in Release 8 440C-ENET Ethernet Plug-in for Guardmaster 440C-CR30 Safety Relay Predefined Input tags available for: I/O Terminal status Verification ID Faults Logic function status  Ethernet allows you to:  Monitor 440C-CR30 from Studio 5000 Logix Designer™ or Connected Components Workbench software

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 47  Troubleshoot 440C-CR30 safety system on HMI or in automation controller with diagnostic information shared over EtherNet/IP. What’s New in Release 8 440C-ENET Ethernet Plug-in for Guardmaster 440C-CR30 Safety Relay Fault Codes can be used to display detailed fault and recovery information on an HMI

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 48  Share standard Control signals between automation controller and 440C-CR30 safety relay (resets, feedback, etc.) Select the corresponding Communications input to use in your safety relay logic What’s New in Release 8 440C-ENET Ethernet Plug-in for Guardmaster 440C-CR30 Safety Relay Send signals from the controller to the 440C-CR30 using the predefined Output tags created by the AOP

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 49  System Integration with Micro800 controllers Design Software Control Level Device Level Information Level 440C-CR30 HMI Controller What’s New in Release 8 440C-ENET: Supported Topologies  Design Software : Connected Components Workbench R8 or later  Controller :  Micro820, all releases  Micro850 firmware revision 4 or later  HMI : PanelView Component (No direct connection between 440C-CR30 and PVc over Ethernet at launch)  440C-CR30 : Revision 8 or later firmware and 440C- ENET plug-in

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 50  System Integration with MicroLogix 1100/1400 controllers Design Software Control Level Device Level Information Level 440C-CR30 HMI Controller What’s New in Release 8 440C-ENET: Supported Topologies  Design Software :  Explicit Messaging : RSLogix 500 software  440C-CR30 Configuration : Connected Components R8 or later  Controller :  MicroLogix 1100/1400  HMI : PanelView Component (No direct connection between 440C-CR30 and PVc over Ethernet at launch)  440C-CR30 : Revision 8 or later firmware and 440C- ENET plug-in

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION C-ENET: Supported Topologies What’s New in Release 8  Read 440C-CR30 input assembly with CIP Generic Message in MicroLogix 1100/1400 controller:  Write to 440C-CR30 output assembly with CIP Generic Message in MicroLogix 1100/1400 controller:  See Appendix E of publication 440C-UM001D for member descriptions.Appendix E of publication 440C-UM001D

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION 52  System Integration with Logix controllers  with AOP version 1.00 (available in March 2015) Design Software Control Level Device Level Information Level 440C-CR30 HMI Controller What’s New in Release 8 440C-ENET: Supported Topologies  Design Software :  I/O Messaging : Add-on Profile in Studio 5k v20 or later  440C-CR30 Configuration : Connected Components R8 or later  Controller : Logix5000 controller, firmware revision 20 or later  HMI : PanelView Plus (No direct connection between 440C-CR30 and PVP at launch)  440C-CR30 : Revision 8 or later firmware and 440C-ENET plug-in

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION Overview Release 7 – September 2014

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 7 54  Assign unique and meaningful names to function blocks.  Names stored in safety relay on Download and recovered on Upload  Double-click or right-click function block name to edit name Rename Function Blocks

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 7 55  Generate complete, printable report  Exports to Microsoft Word or WordPad.  Includes all configured parameters and pictures of application logic.  Generate Report button included on toolbar in the Safety Editor. Generate Printable Report

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 7 56  Setting a password restricts software connections to the safety relay:  Operations Upload, Download and Connect are restricted without password  Provides two primary values:  Prevent unwanted change to safety relay configuration.  Protects Intellectual Property - the unique configuration in the safety relay Password Protect Safety Relay

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 7 57  Support for 2080-MEMBAK-RTC module:  Store application on memory module for easy recovery  Also supports backing up application AND firmware  Backup and Restore applications without Software:  Press Backup button on Memory module to backup application.  Press Backup button on Memory module and MEM/ID button on CR30 to Restore an application Application Backup and Restore with Memory Module

Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. PUBLIC INFORMATION What’s New in Release 7 58  Four additional 2080 Digital plug- ins supported: Additional 2080 Digital Plug-ins Supported Catalog #DescriptionList Price in USD 2080-IQ4OB48-pt Combo, 4-pt Digital Input, 12/24VDC, Sink/Source, IEC3, and 4-pt Digital Output, 12/24VDC, Source $ IQ44-pt Digital Input, 12/24VDC, Sink/Source, IEC3 $ OB44-pt Digital Output, 12/24VDC, Source,$ OW4I4-pt Relay Output, Individually Isolated, 2A $69 NEW!