10/28/09E. Hazen FNAL Workshop1 HCAL DAQ / Timing / Controls Module Eric Hazen, Shouxiang Wu Boston University

10/28/09E. Hazen FNAL Workshop2 DTC Requirements ● Clock / Controls ● Receive TTC and/or upgraded controls stream ● Distribute clock and synchronous controls ● DAQ ● Readout DAQ data, optionally perform ZS or SR ● Transmit to SLink (via adapter) and/or new DAQ ● Must be an MCH card for connectivity ● Could eventually perform minimal MCH functions

10/28/09E. Hazen FNAL Workshop3 Existing HCAL Crate (complex cable plant!) Front-end Fibers (8x) Total 48 ch/HTR CAEN VME Bridge HTR VME Module DCC VME Module TP to RCT Vitesse serial TTC fanout VME Module HTR to DCC LVDS serial TTC/clocks SLink-64

10/28/09E. Hazen FNAL Workshop4 MicroTCA HCAL Crate

10/28/09E. Hazen FNAL Workshop5 Vadatech VT891 - commercial uTCA crate AMC 1 - SuperHTR AMC 2 - SuperHTR AMC 3 AMC 4 AMC 5 AMC 6 AMC 7 AMC 8 AMC 9 AMC 10 AMC 11 AMC 12 DTC (MCH2) MCH1 MCH1 (commercial): Ethernet, management interface MCH2 (DTC): Clock/controls distribution, DAQ

10/28/09E. Hazen FNAL Workshop6 MCH Mechanics (in progress) Front panel space very tight! Barely room for 3 SFP+ and TTC receiver T1 T2 T3 T4 MCH requires 4 connectors Plan is to use 2 PCBs, with connectors only at other two sites. Front panel Harting AMC, MCH plug connectors Harting MCH flex adapter

10/28/09E. Hazen FNAL Workshop7 DTC Clock / Controls PCB

10/28/09E. Hazen FNAL Workshop8 DTC DAQ board SFP+ Virtex 5/6 FPGA MCH Connect or 3 (4) Fabric D to AMC 1-12 DAQ MCH Connect or 3 (4) Fabric E to AMC 1-12 Spar e DAQ fiber Ethernet fiber Spare fiber Clock / Controls from Clock PCB ~ 6Gb

10/28/09E. Hazen FNAL Workshop9 Status and Plans ● Goal -- Test beam summer 2010 with uTCA system! ● Good news: FY10 funding approved as req'd ● SuperHTR / miniCTR2 card built at Minnesota and under test ● uTCA test crates available at BU, MN ● Detailed design just starting for DTC

10/28/09E. Hazen FNAL Workshop10 Spare Slides

10/28/09E. Hazen FNAL Workshop11 MicroTCA Introduction ● New telecom standard from PICMG ● 75mm high cards with ~ 10Gbit/sec serial backplane (up to 20 ports) ● Selected for SLHC trigger platform for CMS Example “Matrix” card developed by LANL

10/28/09E. Hazen FNAL Workshop12 DTC Board Stack ● Build boards 1, 2 first ● Board 1: Power, controls ● Board 2: Clocks ● Build boards 3, 4 second ● DAQ concentrator

10/28/09E. Hazen FNAL Workshop13 DTC Block Diagram

10/28/09E. Hazen FNAL Workshop14 Typical MicroTCA Backplane Typical 12-Slot MicroTCA Backplane (Schroff)

10/28/09E. Hazen FNAL Workshop15 Typical MicroTCA Backplane Two MCH “Hubs” One will be commercial (for system control) (for HCAL, second will be our DTC)

10/28/09E. Hazen FNAL Workshop16 Typical MicroTCA Backplane 12 identical AMC slots (for HCAL, SuperHTR)