1 Rear Access Door Lid Lid Latches Key Pad ADA Port Headphone Jacks Ballot Feed Tray Key-Operated Mode Switch Compact Flash Touch Screen Monitor AutoMARK

2 THE AUTOMARK=ACCESSIBLE Enables voters to vote independently. (Blind, Illiterate, Disabled, or Anyone!) Enables voters to vote independently. (Blind, Illiterate, Disabled, or Anyone!) It will read the ballot to the voter and mark the voter’s choice. It will read the ballot to the voter and mark the voter’s choice. It is a ballot marking device only and does not count the ballot. Ballots must be put in the DS200 to be counted. It is a ballot marking device only and does not count the ballot. Ballots must be put in the DS200 to be counted. It must be set up! Do this the night before. It must be set up! Do this the night before.

3 Step 1: Removing the Automark From the Case Lay case flat. Lay case flat. Pull up on latches located on each side toward the front and lift lid. Pull up on latches located on each side toward the front and lift lid. Two people should lift the AutoMARK from the case and place on a table. It is easiest to hold on the sides. Two people should lift the AutoMARK from the case and place on a table. It is easiest to hold on the sides.

4 Step 2: Plugging in the Power Cord Plug female end of the cord into the back of the machine. Plug female end of the cord into the back of the machine. Plug male end into a power strip or extension cord if needed. Plug male end into a power strip or extension cord if needed.

5 Step 3: Installing the Ink Cartridge Lift the Rear Access Door. Lift the Rear Access Door. Insert the cartridge into the square black box. It will click twice. Insert the cartridge into the square black box. It will click twice. Close the Rear Access Door. Close the Rear Access Door.

6 Step 4: Opening the Screen Slide the Lid Latches Out. Slide the Lid Latches Out. Lift the lid flap, rotate back until it rests on top of the lid. Lift the lid flap, rotate back until it rests on top of the lid. Lift the entire lid away from you in a vertical position. You will see the Touch Screen Monitor under the lid. Lift the entire lid away from you in a vertical position. You will see the Touch Screen Monitor under the lid. Lift the Monitor toward you into a vertical position Lift the Monitor toward you into a vertical position Close the lid. Close the lid. Pull the Ballot Feed Tray Up and Out. Pull the Ballot Feed Tray Up and Out. Plug in the Headphones. Plug in the Headphones.

7 Step 5: Turning the AutoMARK ON Take the YELLOW Key and insert in the Key- Operated Mode Switch. Take the YELLOW Key and insert in the Key- Operated Mode Switch. Turn to ON. Turn to ON. It will take a few minutes for the machine to come on. It will take a few minutes for the machine to come on.

8 AutoMARK Features Several buttons are available at the bottom of the screen such as (PREVIOUS, ZOOM IN/OUT, HIGH CONTRAST, EXIT RETURN BALLOT, NEXT) Several buttons are available at the bottom of the screen such as (PREVIOUS, ZOOM IN/OUT, HIGH CONTRAST, EXIT RETURN BALLOT, NEXT) Volume and Tempo may be adjusted using the keypad to the right. Volume and Tempo may be adjusted using the keypad to the right. The diamond shaped screen button may be used to turn the screen off for privacy. The diamond shaped screen button may be used to turn the screen off for privacy. A marked ballot may be inserted and reviewed by the voter, but cannot be additionally marked or changed. A marked ballot may be inserted and reviewed by the voter, but cannot be additionally marked or changed.

9 Using the Automark Any Voter May use the Automark. The screen should display, Insert Your Ballot The screen should display, Insert Your Ballot The Voter will insert their blank ballot. The Voter will insert their blank ballot. The voter may use the touch screen or the key pad to the right. The voter may use the touch screen or the key pad to the right. The audio instructions correspond with using the keypad. The audio instructions correspond with using the keypad. After the ballot has been marked it will be returned to the voter. They should then deposit the ballot into the DS200 unit. After the ballot has been marked it will be returned to the voter. They should then deposit the ballot into the DS200 unit.