Rigaku Rotary Assembly Top View shows “Inlet” side. This couples with 4-ea ¾“ bolts to “Offset” flange. This flange has central hole 1” offset from center.

Slides:

Advertisements

Similar presentations

Machining a V-Block Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved. 1.

Advertisements

EML 2023 – Modeling, Assemblies Lecture 3.2 – Assemblies, part 2.

Test Chamber Assembly, 1.5M Long (59.00”) Vacuum Tube, 4.00 OD x 3.50 ID Vacuum Tube, 3.75 OD x 3.51 ID 3.375” CFF, Non-Rotatable Feedthrough, Ceramtec.

E-Zapper Exit - Plasma Window 18 MeV Electron Accelerator Plasma Igniter Plasma Window Beam in Atmosphere Fast- Acting Valve 2 um Be Window Mechanical.

994 RPDA 21/2”- 6”. Modification Overview  Production of the 994RPDA began in 1999 and is current.  The 994 RPDA currently utilizes the ¾” 009M3 for.

4- Flywheel and Crankwheel. The kinetic energy in the flywheel caries the engine through the portion of its rotation where there is no energy input, therefore.

Connecting crank and pivot shaft assemblies. Press fits, or interference fits are sometimes used in manufacturing to reduce manufacturing costs or liabilities.

Manip 6” Diameter TSP shield Top Level Middle Level Bottom Level Lower Level CF flanges Not threaded except wide bore Table top 3’ high (Al table top)

APPENDIX A (RFI) FOR THE FABRICATION OF MULTIPLE STEEL REACTION STRUCTURES FOR NASA-MSFC STRUCTURAL TESTING Mike Roberts 12/2/09.

MC Type-B fit up review1 Review of MC Type B assembly clearances reviewing A-to-B and B-to-C interfaces 3/1/07 Summary: Wing interfaces look okay between.

Using the Alphabet of lines. Drawing should be near bottom left corner. The front view shows how wide and how tall the object is.

Sector of a Circle Section  Sector – portion of the area of a circle area of sector = arc measure area of circle 360 Definitions & Formulas.

994 2½ ”- 10”. Modification Overview  Production for the 994 began in 1999 and is current.

Motion Constraint Train Down the Track. Apply Angle Constraint to Workplanes Train is assembled at this point. Place a Workplane through the center of.

2012 IDEA ASSEMBLY “HINT” PACK. ARM: draw in 2D Copy / paste this view into Inventor.

1 Manufacturing Projects Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved.

Three Ways to Draw a Threaded Bolt Even though they look different, they all mean the exact same thing. It is the CALL-OUT information that is critical.

STEP 1: ASSEMBLE INSERT PLATES 1.Assemble insert plates by press fitting roller bearing and adapter plate into assembly 1.1 Prep all mating surfaces to.

10.0 Conic Sections. Conic Section – a curve formed by the intersection of a plane and a double cone. By changing the plane, you can create a circle,

774X DCDA 21/2”, 6”, 8” 774X DCDA 21/2”, 6”, 8”. Modification Overview  Production began in  The 2 ½” 774X DCDA was discontinued in  The.

Flexible Manufacturing

Calculate the Surface Area of a Cone and Sphere

Equations of Circles.

Section 1.5 Circles Copyright © 2013 Pearson Education, Inc. All rights reserved.

11.6: Surface Area and Volume of Spheres

CHAPTER 10 CONIC SECTIONS Section 1 - Circles

Sectionals Sliced view of a part or component in a drawing showing its internal make up.

10.6: Circles and Arcs. 10.6: Circles and Arcs.

ME Contest Structure Plan View dia. orange circle

Equations of Circles.

774X 21/2”, 6”, 8”.

Section 10.1 – The Circle.

2000SS 2½”-12”.

Development of Surfaces

Circle Unit Notes AA1 CC.

Lesson 9-4 Spheres Lesson 9-4: Spheres.

Section 10.1 Tangents to Circles.

Introduction to SolidWorks

Fastening devices.

PBC Method Flat Mirror Gas Mixture Dielectric Mirror Pump Window PM

Gaskets and Packing An introduction to Gaskets Packing

What is a radius of a circle? What about the diameter?

11.7 Circles in the Coordinate Plane

Equations of Circles.

C H A P T E R 72 Auxiliary Views.

Break down Lance rack Cut one of each of these for each rack

GEOMETRY Circle Terminology.

4.1 Equations of circles Arcs, Inscribed Angles, Central Angles

Circles in the Coordinate Plane

774 DCDA 21/2”-12”.

5000SS 21/2”- 6”.

Lesson 9-4 Spheres Lesson 9-4: Spheres.

Spheres! Section 11.4.

2000SS 2½”-12”.

A sphere is the set of all points that are equidistant from a given point called the center. Does a sphere have lateral area? A = V =

Lesson 9-4 Spheres Lesson 9-4: Spheres.

774 2½”-12”.

3000SE 21/2”, 6”, 8”.

Parts, Circumference, Area

Miniature Train.

Miniature Train Project

Circles Chapter 7 Section 7.6.

10-1/10-2 Circumference and Measuring Angles & Arcs

Chapter Equations of Circles.

Presentation transcript:

Rigaku Rotary Assembly Top View shows “Inlet” side. This couples with 4-ea ¾“ bolts to “Offset” flange. This flange has central hole 1” offset from center. Bottom View shows “Outlet” side. This couples with twin flanges using 18-ea holes tapped holes Both ends of Rigaku assembly has o-ring groves. So end-flanges only need polished surfaces

Inlet Side of Rigaku Assembly Center section in recessed from outer edge. Outer bolt holes: 4-ea (3/4”) on 7” diameter circle. O-ring groove has ID=5¾“. Recessed portion of surface has an OD=5½”. Central hole = 3.0”. Mating flange should be offset exactly 1.0”.

“Offset Flange” (inlet side) 4 ea ¾” holes Centers 7” Dia. (not tapped) Polish one side For o-ring surface ID = 5½”, OD = 6” Transmission Hole is 3” dia., 1” offset

Outlet Side of Rigaku Assembly 18 Blind-tapped holes, (4¼“ bolt hole radius) O-ring grove diameter is: ID= 3”, OD = 3 3/8”