Installs, Dismantles. A. INSTALLS 1. The lower part of Beam should be installed by 2 Supports, which are proved safely. - Support should be maintained.

Slides:

Advertisements

Similar presentations

Buildings and Structures 1

Advertisements

PUMP JACK/LADDER JACK SCAFFOLD PHOTO COMPLIANCE GUIDE

Chapter-2 Parts of Steel Bridge.

Concrete Fooring & Roofing System

Heavy Concrete Construction Formwork

Commercial Framing C D Prints Unit 13.

Glenn Murcutt SRT 251 Construction and Structures Warehouse and Office complex scenario Stacy Ambelas

Pulleys Vanderbilt Student Volunteers for Science Fall, 2010 Training Refresher.

Chapter-7 Bond Development Length & Splices

Chapter 34 Bridge Construction.

Residential Framing Prints Unit 14.

A dome is a structural element of architecture that resembles the hollow upper half of a sphere. Dome structures made of various materials have a long.

OSHA Subpart Q Concrete and Masonry Construction.

Work Safely Safety Training Tips for Working with your Ladder.

The CKOV support By P Lau. Hall space available to the Ckov & TOF 0 Beam line 3.

EUROCODES - Background and Applications – Moscow 9-10 December 2010 Prof. Ing. Giuseppe Mancini - DISTR - Politecnico di Torino 1 EUROCODE 2 – Design of.

Framed Building Structure Lectured By: Ms. Noorhidayah Sunarti 15/4/2010.

Michelle Perticarari Rebeca Peña

FALL PROTECTION. WHY? –BECAUSE: Falls accounted for 10% of fatal work injuries in 1994 & Serious hazards can be present while above ground. –Examples:

Floor Systems and Foundation Support

Stresses Found In Structural Members. Forces Acting Simply Supported Beam 1.Bending.

The ground must push up as hard as the building pushes down

Topic 7: Timber Subfloor Systems – Basic

Preparatory Seminar for STL Examination By Dr. James Lau, BBS JP.

The Waddell A-Truss Bridge

Umm Al-Qura University Department of Civil & Structural Engineering 1 Design of reinforced concrete II Design of one-way solid slabs Lecture (1)

Plain & Reinforced Concrete-1 CE-313

BEAMS AND COLUMNS.

2 nd Year Trade Overview M. S. Martin Revised Feb

An Introduction to Pandrol’s PANGUARD System

BEAMS AND COLUMNS PRESENTED BY K.ROSHIN RUKSHANA.

FOOTINGS. FOOTINGS Introduction Footings are structural elements that transmit column or wall loads to the underlying soil below the structure. Footings.

FORMS, SCAFFOLDING and STAGING

Chapter 32 Floor Systems and Foundation Support. 2 Links for Chapter 32 Slab Construction Reinforcing Concrete Crawl Spaces.

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

NUMBER OF FLOORS: means the number of floors that are counted from the vertical section of a building at a point where the building has the most floors.

Day 20 PRECAST AND PRE-STRESSED CONCRETE Pre Cast concrete comprise units that are made under controlled conditions, with necessary preparations for.

Residential Construction

RC AND PREFABRICATE ROOFS, PURLINS, FRAMES, CANTILEVERS AND ARCHES

TYPE OF STAIRS STRAIGHT-RUN STAIRSQUARTER-TURN STAIR HALF-TURN STAIR SPIRAL STAIRS WINDING STAIR CIRCULAR STAIR Building construction illustraded 4 th.

Neutrino 1 Assembly Process. Neutrino 2 Assembly Process Step 1: Basement I beams positionned and fixed on the ground. Flatness checked.

Repair and Strengthening of Concrete Bridges and other Structures

Floor Systems and Foundation Support

Chapter-2 Parts of Steel Bridge. contents Bearings Horizontal and transversal wind bracing Classification of bridges.

Leads Institute of Technology & Engineering

Foundation – jay Desai.

Structural Slab Analysis

Framing Vocabulary Stud: upright beams in the framework of a building

Commercial Floor Systems

INTRODUCTION to EUROFORM

ERECT AND DISMANTLE STEEL TUBULAR SCAFFOLDING WITHIN OSHA GUIDELINES.

Molasses explosion 1919 Boston

Types of ground floors.

FORMWORK FORMWORK COMPONENTS Scaffold frames Plywood

Building Construction Technology I

SeminAR ON LINTELS --SANTHOSHKUMAR.M..,.

Chapter-2 Parts of Steel Bridges.

CONCRETE FORMWORK Formwork.

Building Construction I Sofia Sebastian 1

Building Construction I Sofia Sebastian 1

Arch205 building construction floor & Roof systems

Building Frame (Column & Beam)

MATERIALS AND CONSTRUCTION I

Commercial Floor Systems

Commercial Floor Systems

Concrete A structural material made by combining cement, sand, aggregate, and water.

. The sheathing for a floor form is secured to the beam or girder side when forming a monolithic beam or girder and floor slab systemBlock bridging is.

Bunker Wall Design Wall ESS

TRADA trusses TRADA trusses may look complicated but if you run through this sequence a couple of times the construction should be easier to understand.

Presentation transcript:

Installs, Dismantles

A. INSTALLS 1. The lower part of Beam should be installed by 2 Supports, which are proved safely. - Support should be maintained vertically. 2. Worker shouldn’t walk with too much load in the form. 3. Workers shouldn’t work sitting on the form. - Worker needs to care for typical work habit. 4. Side beam and Main beam of HORY BEAM fix tightly with Wedge Pin. 5. Material for construction cannot stuff on the HORY BEAM. 6. Timber (25X50) for Plywood Joint should put in the right position and fix. 7. The position of Plywood Joint part is Upper side of HORY BEAM 8. Install separator (tie) right after fabrication of BEAM reinforcing bar. 9. Arrange reinforcing bar of Slab after Separator (tie) installation. 10. Avoid concentrated concreting when Concreting of Slab. B. DISMANTLES 1. Fix movable prefabricated scaffolding on the dismantling position. 2. Two workers dismantle HORY BEAM over the prefabricated scaffolding together. 3. Don’t put too much stress to prevent falling of Side beam when dismantle plywood. 4. Put beam on the ground using rope. Check point when HORRY BEAM installs, dismantles ㈜ 대의가설

WALL FABRICATION SEQUENCE OF HORY BEAM 주 식 회 사 대 의 엔 지 니 어 링 DAE YEE ENGNEERING CO.,LTD 주 식 회 사 대 의 엔 지 니 어 링 DAE YEE ENGNEERING CO.,LTD 1.Choose HORY BEAM correspond to Span.2.Adjust SIDE BEAM correspond to Span. 3.Side plate of wall levels off before HORY BEAM installation. 4.Install in the side plate of wall according to HORY BEAM distance. 5.Put plywood in the top of HORY BEAM. 6.Recheck horizontality of the upper side after putting HORY BEAM. NO. ㈜ 대의가설

THE LOWER PART FABRICATION SEQUENCE OF HORRY BEAM 주 식 회 사 대 의 엔 지 니 어 링 DAE YEE ENGNEERING CO.,LTD 주 식 회 사 대 의 엔 지 니 어 링 DAE YEE ENGNEERING CO.,LTD 1.Choose HORY BEAM correspond to Span.2.Adjust SIDE BEAM correspond to Span. 3.Side plate of beam levels off before HORY BEAM installation. 4.Install in the side plate of beam according to HORY BEAM distance. 5.Put plywood in the top of HORY BEAM. 6.Check verticality of Support after putting plywood. 7.Recheck horizontality on the upper side plate of beam after putting HORY BEAM. NO. ㈜ 대의가설