The easiest way to access Pure & Ultra Pure Water from tap Direct-Q 3 Direct-Q 3, the easiest way to access both pure & UPW from tap ! The easiest way to access Pure & Ultra Pure Water from tap

Introduction Movies to support you for the installation, the operation and the maintenance of a Direct-Q 3. Direct-Q 3, The easiest way to produce pure & ultrapure water from tap ! Throughout this presentation, we are going to show different movies which will support you for the installation, the operation & the maintenance of this system. It will be crystal clear at the end of this show that the DQ3 is the easiest way to produce pure & UPW from tap.

Direct-Q 3 Installation This combines 3 steps : The unpacking & installation of the system The SmartPak installation The connection of filters First of all, we are going to present the DQ3 installation. It consists of 3 steps: 1st- the system itself is unpacked and installed. 2nd- the Smartpak consumable is put in place. And 3rd- the different filters are connected. Each part is now going to be reviewed in detail…

Unpacking & Installing Our first movie is going to show how to unpack & install the system. Install the reservoir valve… and plug ! UV lamp easily accessible for future maintenance Quick Reference Guide always available with the system Just connect to the tap, secure the tubing to the drain…

SmartPak Installation Now the SmartPak is to be installed. Then an air purge and hydratuing phase will be performed. Lets see how it works.

SmartPak Installation Close the valve and allow the tank to fill up for 1h Let flush the pack for 15 min Always wet de SmartPak O-rings Open the reservoir valve Easy positioning of the Smartpak !

SmartPak Purging & Hydrating Start production until the reservoir is empty Connect the Point-Of-Use to the drain

Filters Connection Vent filter connected at the back of the system Final step of the installation: the vent filter and the point-of-use filter have to be connected. Vent filter connected at the back of the system Let produce 1L of water to flush & hydrate the filter New point-of-use filter connection Start production & vent the filter

2 water qualities available : Direct-Q 3 Operation 2 water qualities available : Type 3 from reverse osmosis stored in 6L internal reservoir. Type 1 after the polishing cartridge : dispensed at the point of use We are now going to operate the DQ3 we have just installed. We remind you this system produces 2 types of water: Type 3 water from reverse osmosis technology. It is stored in its 6L internal reservoir. Type 1 UPW dispensed at the point-of-use The next films will show how to access these purified waters.

Accessing Type 3 Water in the Internal reservoir Depending on the system installation, the type 3 water access can be different Reservoir valve integrated in the wall mounting bracket Reservoir valve available nearby the system, on the bench

Delivering Type 1 Water at Point Of Use The UPW is delivered at the POU after a brief recirculation step… Before producing type 1 water, allow internal water to recirculate Press once on the trigger to dispense the ultra pure water Check volume in reservoir… then press again to stop dispensing

The Ultra Pure Water Volumetric Dispensing The UPW is delivered at the POU after a brief recirculation step… Enter the appropriate mode FO1 Choose the required volume pressing + or - key Start UPW production : the system automatically dispenses the expected volume

Direct-Q 3 Maintenance A maintenance greatly simplified ! 3 STEPS ONLY ! Changing the SmartPak & Filters Replacing the UV Lamp Sanitizing the reservoir Similarly to the installation & operation, the maintenance of the DQ3 has been greatly simplified in order to make the customers’ work easier & quicker. It only consists of 3 steps which are going to be described in details through the following slides.

SmartPak Replacement 1st step, the replacement of the SmartPak when the system asks for it. Flush 15min to the drain then refill the reservoir Replace the old pack & drain the reservoir The red SmartPak icon flashes as an indicator

UV Lamp Replacement (once every 2 years) 2nd maintenance operation : the UV lamp replacement every 2 years. The system will also specifically ask for it. This step is always followed by the UV lamp timer resetting. Gloves to protect the lamp integrity Goggles in case of glass break The red UV lamp icon flashes as an indicator In the C05 mode, reset the timer for the next UV reminder to be on-time

Internal Reservoir Sanitization Finally the customers can sanitize the DQ3 internal reservoir. Millipore recommends such a cleaning once every year, particularly for customers’ applications sensitive to microbial contamination. To efficiently rinse, refill the tank then empty it again Let the system fill the tank - wait for 1 hour, then drain Chemical sanitant = Hydrogen Peroxyde 30% & purified water The ‘sanitization kit’ includes the necessary accessories By the vent filter access, inject 100mL of chemical then 100mL of pure water

Conclusion Easy to install Easy to operate Easy to maintain And good looking ! The Direct-Q 3 is THE solution for customers needing low volumes of Pure & Ultra Pure Water from tap ! Easy to install. Easy to operate. Easy to maintain. And good looking !!! The DQ3 is THE solution for customers needing low volumes of both pure & UPW water from tap. Thank You.