Task T6.2 Tertiary Buildings infrastructures installations WP6 Pilot Set-up, Model Calibration and Assessment Task T6.2 Tertiary Buildings infrastructures installations CNet / CERTH

Overview Selected DEMO Pilot sites at CERTH ITI Building Equipment Procurement / Installation Status per space Sensor Integration to LS and Data Availability through IAM Detailed presentation of equipment installation at DEMO Areas Equipment Installed for DEMO at CERTH

CERTH Pilot areas selected for DEMO Selected CERTH ITI Building areas: 1st Floor: Developer’s Office, Meeting Room, Corridor & Rest Area Ground Floor: ITI Kitchen ITI Building 1st Floor ITI Building Ground Floor

Equipment Procurement / Installation Status per space Developer’s Office Meeting Room Corridor & Rest Area Kitchen Add Dimmable Lights Done - Replace Lights Actuators No Door Double-Beam Sensors Installed Indoor Luminance Acoustic Sensors External Temperature + Luminance Installed at the South – West side of ITI’s Building. RFID First Trials Pending Water Heater Refrigerator

Sensor Integration to LS and Data Availability through IAM Pilot Installation (CERTH) LS IoT Implement. (CNet) Integration to LS – Mapping (CNet) Data Stored in IAM (TUK) HVAC Monitoring: Status & Room Temp HVAC Control: ON/OFF and Set Temp OPC Server OK Mapping Started – Pending NO Lighting Monitoring & Control EnOcean Actuators NO – Integration Pending HVAC & Light Energy Consumption EnOcean Clamps OK ( for the DEMO) CO2 / Temp/Hum OK [2] OK [1] (Mapping Pending) Indoor Luminance OK [7] OK [4] (Mapping Pending) Outdoor Luminance/Temp/Humid

Sensor Integration / Data Availability Planning Pilot Installation IoT Implem. (CNet) Integration to LS – Mapping (CNet) Data Stored in IAM (TUK) Occupancy Sensor Data (Kinect, PIR, Double Beams etc.) OK OK? Occupancy Extraction Events ( Occupancy /Prediction per Space) Office & Home Appliances Monitoring & Control (PC Screens, printers, Microwave Ovens, etc.) SmartPlugs [37] OK [37] OK [32] (Mapping Pending)

Developer’s Office – Occupancy Extraction 5 Kinect Cameras installed Re-configured and tested 5 different topologies Optimized Topology selected utilizes 5 Kinect Cameras (due to obstacles in the office) Exact Number of Occupants for 4 sub-spaces

Developer’s Office – Occupancy Extraction Motion Detectors Passive Infrared Radars + Magnetic Traps (Alarm System integration) Real Time Response Time High Accuracy Low cost solution Used for RFID automated Control

Developer’s Office – Occupancy Extraction Door Counters Active Infrared Double-Beams High Accuracy Low Cost Pressure Mats Medium / Low Accuracy Extremely Low Cost Connected to Arduino – integrated to LS through MySQL Provide Occupant’s Direction Will be used to trigger RFID Control Combination scenarios will further be tested to check accuracy gain compared to separate solutions

Developer’s Office – User Profiling – Energy Consumption Smart-plugs monitoring & control + consumption measurement HVAC monitoring + controls Already installed on most office appliances LS - OPC Implemented, Integration Pending 7 x PC Towers ( No Control ) Actual Temperature 8 x PC Monitors ( On/Off Control) Set Temperature 1 x Printer (On/Off Control) On/Off Status Lighting monitoring + controls (Dimmable – EnOcean) Replaced all Lights with Dimmable ones (to allow User Profiling scenarios to be tested) Dimmable actuators installed LS Integration Implemented Validated both Read & Send Control Commands through LS On/Off Dimming Level

Developer’s Office – User Profiling – Energy Consumption Wireless EnOcean Power Meters with Clamps installed for both HVAC & Lighting Measurement of AC Current Environmental Temperature (through HVAC) Each Thermal Zone returns the respective value BACNet Protocol – OPC Server 3 Luminance Sensors Installed Each Visual Zone is covered separately Wireless EnOcean Sensors

Developer’s Office – Zones Thermal Zones Visual Zones Occupancy Zones

Meeting Room – Occupancy Extraction Motion Detectors Door Counter (Double-Beams) CO2 Late Response Time Environmental Disturbances Acoustic Sensor (connected to Arduino)

Meeting Room - User Profiling – Energy Consumption HVAC monitoring + controls Lights are measured by the EnOcean Actuators LS - OPC Implemented, Integration Pending HVAC consumption will be simulated through Models Lighting monitoring + controls (Controllable – EnOcean) Hardware Installation Competed LS Integration Implemented, Validation Pending On/Off Smart-plugs: Monitoring & Control + consumption Measurements All Available Plugs (power-strips) covered – Group Based Measurements

Meeting Room - User Profiling – Energy Consumption Environmental Wireless EnOcean Indoor: Temperature /Luminance Outdoor: Temperature / Luminance/ Humidity DEVELOPER’S OFFICE MEETING ROOM Luminance Temp / Hum

Corridor & Rest Area - Occupancy Motion Detectors Acoustic Sensor (Connected to Arduino)

Corridor & Rest Area – User Profiling – Energy Consumption Environmental HVAC monitoring + controls Temperature / Luminance (+ Motion) LS implementation ok Lighting monitoring + controls Integration Pending Hardware Installation Pending (Not available for the Demo Pilot) LS Integration & Validation Pending Smart-plugs monitoring + control + consumption SmartPlugs to all Office Appliances Smart Water Heater Pending Energy Consumption No - Lights & HVAC will be simulated

Corridor & Rest Area - Zones Thermal Zones Visual Zones Occupancy Zones

Kitchen – Occupancy Extraction Kinect Cameras Depth Image Utilization Validated Real Time Occupancy Extraction Optimized Topology for Occupants Exact Number Acoustic sensor (connected to Arduino)

Kitchen - Occupancy Occupancy Extraction Motion Detectors Door Counters Active Infrared Beams CO2 / Temp / Hum Extract occupancy through appliances Usage as received through Smart Plug monitoring) Pending to be tested

Kitchen – User Profiling & Energy Consumption HVAC monitoring + controls Lights are measured by the EnOcean Actuators Lighting monitoring + controls HVAC will be simulated through DER models (Controllable – EnOcean) Hardware Installation Competed LS Integration Implemented, On/Off Smart-plugs Monitoring & Control + Consumption measurement All Home Appliances are Being Measured LS Integration Implemented & Validated

Kitchen - Zones Thermal Zones Visual Zones Occupancy Zones

RFID Deployment for DEMO Initial trials with demo equipment Installation pending 4 x Antennas 1 x 4-port Reader

Equipment Installed for DEMO at CERTH Developer’s Office Corridor & Rest Area Meeting Room Kitchen Total Kinect 5 - 1 6 PIR 3 Active Infrared Double-Beams 4 2 8 Pressure Mats Acoustic CO2 / Temperature / Humidity Indoor Luminance 7 Outdoor Luminance Outdoor Temperature / Humidity Smart-Plugs 16 28 Dimmers Actuators Indoor HVAC Cassettes ( Temp )

Questions & Discussion Thank You !!!