IP marketing G Haruka Igarashi 2017/3/1 Ver1.0 Product Guide IP marketing G Haruka Igarashi 2017/3/1 Ver1.0 Note: The information in this document is subject to change without notice.

Features 360° direct print on cylindrical items On-demand printing ― original products can be made by one unit. Printable on cylindrical items which length is 600mm and diameter of 10ｍｍ to 110ｍｍ Printing on wide variety of cylinder items broadens the range of application. 　　 *The maximum weight is 2kg(Large diameter) and the maximum print width is 600mm(KebabMkⅡL). Simple installment on UJF-3042/6024MkⅡ, UJF-7151plus Quick replacement on the table is possible, because the option is easily removable by a special connector.

KebabMkⅡ/KebabMkⅡ L Comparison table Appearance Supporting models UJF-3042MKⅡ UJF-6042MkⅡ UJF-7151plus ink LH-100 LUS-120 LUS-150 LUS-150(onlyUJF-6042MkⅡ) LUS-350(onlyUJF-7151plus) Printable area 30mm～300mm 30mm～600mm Printable diameter 10mm～110mm Maximam weight of print material Small diameter:1.5kg Large diameter:2.0kg Weight About3kg About6kg

360° direct print on cylindrical item Print by rotating the substrate,able to print on 360 degrees. How to create data ①Measure the diameter ② Diameter x pi (3.14)＝Circumference ③Flat data is obtained Print on curved surface width diameter Print area width Circumference

Cylindrical items of 30mm to 600 length and 10ｍｍ to 110ｍｍ in diameter can be printed Unit adjustment *Picture is Kebab Mk IIL Narrow span Setting Example of wide span setting Example of narrow span setting Wide span Setting ※ It is not possible to place it on two rollers at the same time. The setting varies depending on the diameter of the item. ・Diameter of 10mm~45mm (0.3937~1.772inch) → Small-diameter Setting * Please set the table spacer to 50 mm. ・Diameter of 45mm~110mm (1.772~4.331inch) → Large-diameter Setting * When the diameter is 64 mm or more, it is not necessary to set the table spacer. *Please fix item by adjusting sliders. *When printing in multi layers, uneven print density or layer gap may occur according to the weight or the surface of the item. Please check the print quality beforehand. *If the work is lightweight,color unevenness is likely to occur. In case of bottles, adding water increases weight, making it easier to stabilize. 5

Some examples of Kebab products Reference value of diameter Narrow span print Wide span print mm Stamp (12mm) Toy (38mm) Atomizer (40mm) Water bottle (57mm) Wine bottle (62mm) Japanese sake bottle (72mm) Glass bottle (85mm)

Print speed KebabMkⅡ/L＋UJF-3042/6042MkⅡ 1.Diameter10ｍｍ(Mediawidth200mm) Mode Resolution Pass Print conditions Print time Print speed（m2/h） Draft 600x600 8 Color 　　　　2m30s 0.15 Color+White 　　　　　　3m50s 0.10 Standard 600x1200 16 　　　　　　　　　　7m05s 0.05 　　　　　　　　　　　7m35s 2.Diameter60ｍｍ(Mediawidth200mm) Mode Resolution Pass Print conditions Print time Print speed（m2/h） Draft 600x600 8 Color 　　　　　　　5m00s 0.45 Color+White 　　　　　　　　　　　　　　10m40s 0.21 Standard 600x1200 16 　　　　　　　　　　　　　　10m55s 　　　　　　　　　　　　　　　　　　　　　　　　　　　21m15s 0.11 3.Diameter110ｍｍ(Mediawidth200mm) Mode Resolution Pass Print conditions Print time Print speed（m2/h） Draft 600x600 8 Color 　　　　　　　　　6m45s 0.61 Color+White 　　　　　　　　　　　　　　　　13m10s 0.31 Standard 600x1200 16 　　　　　　　　　　　　　　　　13m25s 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　26m45s 0.16 * It is equivalent to the printing speed when using Kebab with UJF-3042FX / HG, UJF-6042.

Print speed KebabMkⅡL＋UJF-7151plus 1.Diameter10ｍｍ(Mediawidth200mm) Mode Resolution Pass Print conditions Print time Print speed（m2/h） Draft 600x600 8 Color 　　　　2m55s 0.13 Color+White 　　　　　4m20s 0.09 Standard 600x900 12 　　　　　4m15s 　　　　　　　5m50s 0.06 2.Diameter60ｍｍ(Mediawidth200mm) Mode Resolution Pass Print conditions Print time Print speed（m2/h） Draft 600x600 8 Color 　　　　　　　　6m40s 0.34 Color+White 　　　　　　　　　　　　　　　13m45s 0.16 Standard 600x900 12 　　　　　　　　　　　10m00s 0.23 　　　　　　　　　　　　　　　　　　　　19m20s 0.12 3.Diameter110ｍｍ(Mediawidth200mm) Mode Resolution Pass Print conditions Print time Print speed（m2/h） Draft 600x600 8 Color 　　　　　　　　　　8m40s 0.48 Color+White 　　　　　　　　　　　　　　　　　　　　17m45s 0.23 Standard 600x900 12 　　　　　　　　　　　　　　　13m00s 0.32 　　　　　　　　　　　　　　　　　　　　　　　　　　　　25m25s 0.16 * Since the configuration of the machine body is different, the speed differs from when using UJF - 3042/6042 Mk II + Kebab MK II.

RasterLink6 【Intuitive Operation】 RIPsoftware 1 2 Edit function for Kebab data only The main information is in one screen. The status of printer, the progress of ripping, the status of job can be checked at a glance. Nesting or composition of job are displayed visually. 1 The visual icons on the right side of the screen allows for the easy and quick setting of the print condition. 2 "Kebab printing" icon menu An icon for Kebab appears in the menu list, Print settings are now available on the dedicated screen. 3 Additional function ―“Scale Calculation ”　for Kebab Circumference will be calculated and reflected after the diameter size keys in the software. Frequently used setting can be registered as “My Favorite”. Up to 100 settings can be registered.

Simple installment on UJF-3042/6042 Install Kebab option easily with attaching a specialized connecter on the flat bed with screws. There are M4 taps on the table to fix a jig. Fix the Kebab option with screws, and load a specialized connecter. Workflow 　① Select [Machine setting → Option fixture set] from the operation panel of UJF-3042 / UJF-6042 MkⅡ, UJF-7151plus and lower the table to the bottom. * At this time, according to the diameter of the media table spacer 50mm installed,or remove the table spacer (excluding UJF - 7151 plus) ②Attach a specialized connecter at the back of the table on which the Kebab Mk II / L is mounted. 　③ Fix with screws the block at the specified position. 　④Put the KebabMkⅡ/L on the table. 　⑤Connect the main unit and Kebab Mk II / L with a dedicated connector and select [Option Jig Set: End] from the operation panel. 　⑥[Option fixture set: Kebab Mk II]        [Option Jig Set: Kebab Mk II L] Installation is complete when it is displayed. ※ For details of installation procedure, please refer to the instruction manual. How to attach Kebab Mk II to UJF-3042 Mk II

KebabMkⅡ/L Basic Specification item Kebab MkII Kebab MkII L Parts number OPT-J0432 OPT-J0433 Supporting models UJF-3042MkII UJF-6042MkII, UJF-7151 plus Rotaly degree of print material Over±360°（no limitation） Rotation system Rollers under print material Applicable system Cyllindical objects（uneven surface may sffect rotation） Printable size Diameter 10mm～110mm Length 30mm～300mm 30mm～600mm Printable area Feeding direction（X） Entire surface of the material Head moving direction（Y） 300mm or narrow 600mm or narrow Maximam weight of print material Narrow span setting 1.5kg Wide span setting 2.0kg Interface Connect with the supported printer sing the dedicated connector Installation envioment Temperature 20℃～35℃ Relative humidity 35～65％Ｒｈ Guaranteed precision range 20℃～25℃ (Temperature change：±10℃/ｈ) Dust level Equivalent to normal office level Machine Weight About3kg About6kg Dimentions（W x D x H） 366 × 301 × 50 mm 674 x 301 x 50 mm At packing dimentions（W x D x H） 465 x 385 x 210 mm 775 x 385 x 210 mm

FAQ Question Answer 1 What is the mechanism of printing on curved surfaces? Since the material is placed on the rotating shaft, it is printed while the material itself turns. 2 Is it possible to return to normal printing even after installation? It is possible. You can also change by yourself. 3 How do you fix the jig? The table can be fixed with screws. 4 What is the shape of the material that can be print? Mainly cylindrical shape. Cones and spheres are not suitable. Also, it is essential that the surface irregularities do not affect the rotation of the workpiece. 5 What sizes of media can be set? <KebabMkⅡ> Lenght：30mm～300mm Diameter：10mm～110m <KebabMkⅡL> Lenght：30mm～600mm 6 What is the maximum weight of the media set? It has a small diameter of 1.5 kg and a large diameter of 2 kg. For lightweight work, the rollers slide and may not rotate well. In case of a bottle, putting water in it will increase the stability. 7 How do you adjust the head gap? When you enter the diameter in the work set, the table automatically adjusts the height. The recommended gap is 1.5 mm. 8 Is there a height restriction for work? It is maximum Φ 110 mm. 9 Which model does Kebab Mk II support? It supports UJF-3042MkII. It does not support UJF-6042MkII, UJF-7151plus and existing machines. 10 Which model does Kebab Mk IIL support? It supports UJF-6042Mk II and UJF-7151plus. It does not support UJF-3042MkII and existing machines.

FAQ Question Answer 11 How is the origin coordinated? Chose "Kebab Origin Setting" menu and align with the light pointer. (For large diameter set, you can use origin sensor.) 12 How can we decide to use wide or narrow span setting? It is determined by the work diameter. If it is a thin material less than Φ 45 mm, please use the inner roller (narrow span setting) If it is Φ45 mm or more, use the front roller (wide span setting). * For Φ 10 mm to Φ 64 mm, raise the unit by 50 mm with the table spacer attached to the printer. (excluding UJF - 7151 plus) 13 Is it possible to put more than one work at the same time? It is possible to arrange them side by side within the printable area. In that case, imposition of the image on the RIP or illustrator is required. 14 How do you create data? Create a rectangular data in which the area of the side of the cylinder (height of the cylinder x circumference) is replaced by a plane. 15 What do we need to do for start up? Select [Machine settings → Option jig set] on the main unit panel, and connect and disconnect the dedicated connector. After, select ENT. [Option Jig Set: Kebab Mk II] [Option Jig Set: Kebab Mk II L] Will be displayed. 16 What do we need to do to stop? There is nothing in particular. You can turn off the power while keeping Kebab on the pedestal. Maintain daily maintenance of the printer itself, such as head cleaning. If ink adheres to the roller, please perform maintenance. 17 Can you print primer? Printing can be done, but if data goes round the cylinder, the mark of the roller will be lost. Please consider splitting the data and printing, or printing only on a part. 18 Can you print clear and clear glossy for finishing? Clear data can be printed. Clear glossy finish is not available. 19 Does color unevenness occur during printing? If the work itself is not a perfect circle, slight color unevenness tends to occur.

Revision history Do not use this page Version Dates contents Drafter 1.0 2017/3/1 Create new IP marketing G Haruka Igarashi