Wireless LAB Test Preparation Guide Version 1.0 1

Revision History Revision Number Date Revision Content Revised By 1 DCP LAB Sample Test Revision History Revision Number Date Revision Content Revised By 1 2013/03/31 first release Karl Hsieh 2 3 4 5

LAB Test Rules and Policies DCP LAB Sample Test LAB Test Rules and Policies The candidate needs to finish the test within 3 hours. The passing score for DCP-Wireless LAB Examination is 70 marks. Talking, eating and discussion are not allowed during the lab test session. All mobile devices must be switched off during the session. If a candidate needs to go to the restroom during the session, the candidate must first seek the proctor’s consent. Time of absence for session is counted in the total examination time. If a candidate has a question, the candidate should raise his or her hand and signal the proctor for help. All DCP LAB test materials including, but not limited to the examination sheet, work sheet and answer sheet must not be taken out from the lab testing area. If any event occurs during the lab test session, follow the proctor’s instruction. The proctor retains the right to cancel and stop a candidate’s lab examination.

LAB Test Rules and Policies DCP LAB Sample Test LAB Test Rules and Policies Before ending the test session … Please review your answers carefully Remember to save all the configurations Raise your hand to signal the proctor if you want to end the session LEAVE the test sheets on the table Please Note: Candidates who violate any rule or policy of this test will automatically fail the test.

Equipment Requirement per Candidate DCP LAB Sample Test Equipment Requirement per Candidate Resource Needed Q’ty Firmware Remark DWC-1000 2 4.2.0.2 DWL-6600AP DWS-3160-24PC 1 4.2.0.7 DGS-3620-28TC/SI 2.00.016 DAP-2690AP 1.15rc049 Windows laptops with wireless function RJ45 network cable (1.5 m) 10

LAB Test Topics and Scores DCP LAB Sample Test LAB Test Topics and Scores Item Topic Marks Remark 1 Environment Setup 5 2 Unified wireless switch configuration 20 DWS-3160, DWS-4026 is not included in the test 3 Wireless controller configuration 40 DWC-1000 4 Standalone access point configuration Standalone AP management 6 D-Link Wi-Fi Planner 10 Cloud version Wi-Fi Planner is used in the exam. Instruction will be given. Total 100  

Technologies covered in the configuration DCP LAB Sample Test Technologies covered in the configuration Wireless AP discovery Access point profile creation Wireless security Controller and unified switch clustering Captive portal Wireless AP operation mode Multiple SSID AP array and AP Manager D-Link Wi-Fi planner

Sample LAB Topology DCP LAB Sample Test SWR1 DWC1 DWC2 DWS1 DAP2 DWL1 9 10

DCP LAB Sample Test 1. LAB environment setup 1.1 Please build the lab network based on the provided lab topology and cabling plan in the previous slide. 1.2 Backbone switch SWR1 configuration Switch name: SWR1 IP addressing: 10.90.90.50/8 Switch DHCP information Pool Name DCPWLAN IP Address 10.0.0.0 Netmask 255.0.0.0 DNS Server 10.90.90.10 Default Router 10.90.90.1

2. Unified wireless switch configuration DCP LAB Sample Test 2. Unified wireless switch configuration 2.1 Configure SWR1 as DHCP server based on the information of the table of the previous page 2.2 On DWS1, configure a WLAN using AP profiles (x=group number) Create SSIDs, named dcpwlan-x and dcpwlan_Guest-x. Apply WPA2-Personal/AES security to dcpwlan-x, passphrase=1234567890 Create an AP Profile named profile-x1, and turn off 2.4Ghz radio for this profile. Use SSIDs created in step 1 in this profile Create an AP Profile named profile-x2, and configure transmit power at 50%. Use SSIDs created in step 1 in this profile Discover all Unified Access Points and manage it Apply the profile-x1 to DWL1 and profile-x2 to DWL2 *After you finish the configuration, stop here and request the proctor to verify your configuration.

3. Wireless controller configuration DCP LAB Sample Test 3. Wireless controller configuration Disable SWR1 DHCP server and reset DWL1 and DWL2 configuration 3.1 Configure wireless controller DWC1: Enable the Unified Controller DHCP server and configure the Unified Controller to be a DHCP server with Starting IP Address 192.168.10.200 and Ending IP Address 192.168.10.250 Create SSIDs, named dwc-x and dwc_Guest-x. Apply WPA2-Personal/AES security to dwc-x, passphrase=1234567890 Create an AP Profile named profile-x1, and turn off 2.4Ghz radio for this profile. Use SSIDs created in the first step in this profile. Create an AP Profile named profile-x2, and configure transmit power at 50%. Use SSIDs created in the first step in this profile. Discover both DWL1 and DWL2. Apply the profile-x1 to DWL1 and profile-x2 to DWL2

3. Wireless controller configuration DCP LAB Sample Test 3. Wireless controller configuration 3.2 Configure wireless controller clustering function on DWC1 and DWC2. DWC1 is assigned as the cluster controller. DWC1 is assigned as the cluster controller. Push configuration from DWC1 to DWC2 3.3 Configure captive portal on DWC1 Captive portal group name: cp-dcpwlan; description: DCP exam DWC local user database is used. Create captive portal account/password: cpuser1/cpuser1

4. Standalone access point configuration DCP LAB Sample Test 4. Standalone access point configuration 4.1 Perform multiple SSID configuration on DAP1 Configure two SSIDs and map them to respective VLANs Two SSIDs: ssid10 and ssid20 Map ssid10 to VLAN10 and ssid20 to VLAN20. Apply WEP key security to ssid10 (key:1234567890) Apply WPA2 personal security to the ssid20 (key:dcpwlan) 4.2 Connect DAP2 to DAP1 by means of WDS technology Configure both DAP1 and DAP2 as WDS with AP mode WDS link shall be over 5GHz band; 5GHz radio SSID is ssid5 *After you finish WDS configuration, stop here and request the proctor to verify your configuration.

5. Standalone AP management DCP LAB Sample Test 5. Standalone AP management Disable the WDS configuration before start this test. 5.1 Connect DAP2 to SWR1 5.2 Configure AP Array on the DAP1 and DAP2 based on the following information: Access Point DAP1 DAP2 IP Address/mask 192.168.0.50/24 192.168.0.51/24 Array Role Master Slave Array name/password myarray / dcpwlan

DCP LAB Sample Test 6. D-Link Wi-Fi Planner Go to D-Link partner site or internal single sign up; Select the “Wi-Fi Planner” icon to launch the program 6.1 Import the floor plan given below(FloorPlan.zip) by using D-Link Wi-Fi Planner. Calibrate the map according to the information on the map. 6.2 Input the environment properties based on the floor map description file in the FloorPlan.zip. All inner walls are dry walls whereas outer walls are concrete wall APs are not allow to place in the restroom as well as elevators 6.3 Position APs and generate heat-maps by means of the “Advisor”; change the default “minimum signal strength” from -67 to -50 dBm 6.4 Create a site survey report in Word format