Circles Chapter 10 Sections 10.1 –10.7.

Slides:



Advertisements
Similar presentations
A chord that goes through the center of a circle
Advertisements

Circles. Parts of a Circle Circle A circle is the set of all points in a plane that are a given distance from a given point in the plane, called the.
Tangents, Arcs, and Chords
The given distance is called the radius
Circles Review Unit 9.
Chapter 11. If 2 sides of a triangle are radii then the triangle is ______________.
10.2 Arcs and Chords Central angle Minor Arc Major Arc.
Chapter 10.3 Notes: Apply Properties of Chords
Lesson 8-1: Circle Terminology
Circle Geometry.
Circles Basic vocabulary. History of the Circle The circle has been known since before the beginning of recorded history. It is the basis for the wheel,
StatementReason 1. Given 2. Chords that intercept congruent arcs are congruent Example 1 3. All radii of a circle are congruent.
Chapter 10 Properties of Circles.
The Many Parts of a Circle A B T Secant Tangent Chord.
 A circle is defined by it’s center and all points equally distant from that center.  You name a circle according to it’s center point.  The radius.
6.3 – 6.4 Properties of Chords and Inscribed Angles.
Circles Chapter 12.
Circle Proofs Allie Buksha Geometry Mr. Chester.
Section 10.1 Theorem 74- If a radius is perpendicular to a chord, then it bisects the chord Theorem 74- If a radius is perpendicular to a chord, then it.
11-2 Chords & Arcs 11-3 Inscribed Angles
11.1 Angles and Circles Learning Objective: To identify types of arcs and angles in a circle and to find the measures of arcs and angles. Warm-up (IN)
 A circle is defined by it’s center and all points equally distant from that center.  You name a circle according to it’s center point.  The radius.
12.2 Chords and Arcs Theorem 12.4 and Its Converse Theorem –
11-2 Chords and Arcs  Theorems: 11-4, 11-5, 11-6, 11-7, 11-8  Vocabulary: Chord.
A radius drawn to a tangent at the point of tangency is perpendicular to the tangent. l C T Line l is tangent to Circle C at point T. CT  l at T.
Circles. Circle  Is the set of all points in a plane that are equal distance from the center. This circle is called Circle P. P.
circle - set of all points in a plane at a given distance from a given point in the plane.
Circles: Arcs, Angles, and Chords. Define the following terms Chord Circle Circumference Circumference Formula Central Angle Diameter Inscribed Angle.
Circles Chapter 10 Sections 10.1 –10.7.
 A circle is defined by it’s center and all points equally distant from that center.  You name a circle according to it’s center point.  The radius.
Section 10-2 Arcs and Central Angles. Theorem 10-4 In the same circle or in congruent circles, two minor arcs are congruent if and only if their corresponding.
PROPERTIES OF CIRCLES Chapter – Use Properties of Tangents Circle Set of all points in a plan that are equidistant from a given point called.
circle - set of all points in a plane at a given distance from a given point in the plane.
Chapter 7 Circles. Circle – the set of all points in a plane at a given distance from a given point in the plane. Named by the center. Radius – a segment.
Vocabulary And Properties
Standard Understand and use properties of chords, tangents, and secants as an application of triangle similarity. b. Understand and use properties of central,
Tangent and Chord Properties
Circles Vocabulary.
Unit 2 Day 5 Circle Vocabulary.
Review Tangents, plus Arcs, Central Angles and Chords
Day 1.
Circles and terms related to them
Lesson 8-4: Arcs and Chords
Unit 4: Circles and Volume
Circles Definitions.
Circles.
Chords, secants and tangents
Bell Ringer Write an example of each of the following:
Tangent and Chord Properties
Circle Unit Notes AA1 CC.
Tangent and Chord Properties
Central angle Minor Arc Major Arc
Μη μου τους κύκλους τάραττε
Section 11 – 2 Chords & Arcs Objectives:
Day 3.
Central angle Minor Arc Major Arc
Unit 6 Day 1 Circle Vocabulary.
Angles in Circle Notes Unit 5 Day 2.
All you need to know about Circles! By: Ms. Erwin
Unit 4: Circles and Volume
Unit 1 Circles & Volume.
Introduction to Circle and other related terms
Y. Davis Geometry Notes Chapter 10.
Unit 6 Day 1 Circle Vocabulary.
Central Angles and Arc Measures
Standards: 7.0 Students prove and use theorems involving the properties of parallel lines cut by a transversal, the properties of quadrilaterals, and the.
12.2 Chords & Arcs.
Lesson 8-4: Arcs and Chords
Inscribed Angles.
Circles Chapter 7 Section 7.6.
Presentation transcript:

Circles Chapter 10 Sections 10.1 –10.7

This chapter will be separated into TWO tests. 1st test – Sections 10.1-10.4 2nd test – Sections 10.5-10.7

Parts of a Circle Circle F F F center Use the center to name a circle.

Parts of a Circle chord tangent secant diameter radius Segments & Lines

Radius/diameter radius = ½diameter r = ½ d diameter = 2(radius) Formulas Radius/diameter Circumference radius = ½diameter r = ½ d diameter = 2(radius) d = 2r C = 2∏r or C = ∏d

Types of Angles Central angle Inscribed angle - Vertex is on the center. Inscribed angle - Vertex is on the circle.

Types of Arcs major arc minor arc semicircle M MNO P MO O N MON

Measure of Arcs & Angles minor arc = its central angle major arc = 360 - its central angle 68° 360 – 68 = 292 68° 292°

Measure of Arcs & Angles minor arc = its central angle major arc = 360 - its central angle semicircle = 180 180°

Measure of Arcs & Angles minor arc = its central angle major arc = 360 - its central angle semicircle = 180 inscribed angle = ½minor arc 34° 68°

Arc and Chord Relationships B C D If chords are congruent, then arcs are congruent. then AB CD

If a diameter is perpendicular to a chord, then it bisects the chord. Arc and Chord Relationships If a diameter is perpendicular to a chord, then it bisects the chord. A B G H K

If a diameter is perpendicular to a chord, then it bisects the arc. A Arc and Chord Relationships If a diameter is perpendicular to a chord, then it bisects the arc. A B G H K AH  BH

Arc and Chord Relationships Two chords are  if and only if they are the same distance from the center. A B C D P O R

Test 10.1-10.4 total problem - 57 matching (12) arc or angle with various diagrams (9) arcs and angles with one diagram (18) radius or diameter with one diagram (8) chord/segment diagrams (10)