Network+ Guide to Networks 5th Edition

Slides:



Advertisements
Similar presentations
Network+ Guide to Networks 5th Edition
Advertisements

Network Devices Repeaters, hubs, bridges, switches, routers, NICs.
Chapter Six Networking Hardware.
1 Version 3 Module 8 Ethernet Switching. 2 Version 3 Ethernet Switching Ethernet is a shared media –One node can transmit data at a time More nodes increases.
Networking Hardware.
Chapter Six Networking Hardware.
Ethernet Frame PreambleDestination Address Source Address Length/ Type LLC/ Data Frame Check Sequence.
1 25\10\2010 Unit-V Connecting LANs Unit – 5 Connecting DevicesConnecting Devices Backbone NetworksBackbone Networks Virtual LANsVirtual LANs.
(part 3).  Switches, also known as switching hubs, have become an increasingly important part of our networking today, because when working with hubs,
Connecting LANs, Backbone Networks, and Virtual LANs
Network+ Guide to Networks 6th Edition
Data Network Connectivity 11. Objectives In this chapter, you will learn to: Explain how NICs operate List the most common types of NICs Describe the.
CIS 1140 Network Fundamentals Chapter 6 – Network Hardware Collected and Compiled By JD Willard MCSE, MCSA, Network+, Microsoft IT Academy Administrator.
Network+ Guide to Networks 5 th Edition Chapter 6 Network Hardware.
Network+ Guide to Networks 6th Edition
Chapter Six NetworkingHardware. Agenda Questions about Ch. 11 Midterm Exam Ch.6 Cable kit.
Semester 1 Module 8 Ethernet Switching Andres, Wen-Yuan Liao Department of Computer Science and Engineering De Lin Institute of Technology
Network+ Guide to Networks 6 th Edition Chapter 6 Network Hardware, Switching, and Routing.
A+ Guide to Managing and Maintaining Your PC Fifth Edition Chapter 22 All About SCSI.
Network+ Guide to Networks, Fourth Edition
LECTURE 9 CT1303 LAN. LAN DEVICES Network: Nodes: Service units: PC Interface processing Modules: it doesn’t generate data, but just it process it and.
Common Devices Used In Computer Networks
Brierley 1 Module 4 Module 4 Introduction to LAN Switching.
Repeaters and Hubs Repeaters: simplest type of connectivity devices that regenerate a digital signal Operate in Physical layer Cannot improve or correct.
 Network Segments  NICs  Repeaters  Hubs  Bridges  Switches  Routers and Brouters  Gateways 2.
S3C2 – LAN Switching Addressing LAN Problems. Congestion is Caused By Multitasking, Faster operating systems, More Web-based applications Client-Server.
Chapter 6 – Connectivity Devices
Module 8: Ethernet Switching
11 NETWORK CONNECTION HARDWARE Chapter 3. Chapter 3: NETWORK CONNECTION HARDWARE2 NETWORK INTERFACE ADAPTER  Provides the link between a computer and.
15.1 Chapter 15 Connecting LANs, Backbone Networks, and Virtual LANs Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or.
Cisco 3 - Switching Perrine. J Page 16/4/2016 Chapter 4 Switches The performance of shared-medium Ethernet is affected by several factors: data frame broadcast.
Network+ Guide to Networks 5 th Edition Chapter 6 Network Hardware.
Sem1 - Module 8 Ethernet Switching. Shared media environments Shared media environment: –Occurs when multiple hosts have access to the same medium. –For.
McGraw-Hill©The McGraw-Hill Companies, Inc., 2004 Connecting Devices CORPORATE INSTITUTE OF SCIENCE & TECHNOLOGY, BHOPAL Department of Electronics and.
CCNA Guide to Cisco Networking Chapter 2: Network Devices.
NETWORKING FUNDAMENTALS. Network+ Guide to Networks, 4e2.
Rehab AlFallaj.  Network:  Nodes: Service units: PC Interface processing Modules: it doesn’t generate data, but just it process it and do specific task.
Local Area Networks Honolulu Community College
Network Hardware. Local Area Networks LANs consist of Transmission media and network nodes. The network nodes fall into two major classes: Data terminal.
 Identify the functions of LAN connectivity hardware  Install, configure, and differentiate between network devices such as NICs, hubs, switches, routers,
CCNA3 Module 4 Brierley Module 4. CCNA3 Module 4 Brierley Topics LAN congestion and its effect on network performance Advantages of LAN segmentation in.
Release 16/7/2009 Internetworking Devices Chapter 10 Jetking Infotrain Ltd.
CEG 2400 FALL 2012 Chapter 6 Network Hardware, Switching, and Routing 1.
Network+ Guide to Networks, Fourth Edition
© ExplorNet’s Centers for Quality Teaching and Learning 1 Select appropriate hardware for building networks. Objective Course Weight 2%
Network+ Guide to Networks 6 th Edition Chapter 6 Network Hardware, Switching, and Routing.
Connectors, Repeaters, Hubs, Bridges, Switches, Routers, NIC’s
Network+ Guide to Networks 6 th Edition Chapter 6 Network Hardware, Switching, and Routing.
Network Concepts.
Chapter 4: Network Interface Cards
Youngstown State University Cisco Regional Academy
Chapter 2: Network Topologies & Network Devices
Local Area Networks Honolulu Community College
Connecting Network Components
Networking Devices.
Lecture#8 Network Devices
Chapter 3 Computer Networking Hardware
Components of Computer
Network connectivity to the legacy wired LAN
NETWORK TOPOLOGIES There are three basic configurations used to connect computers they are the Bus Ring Star.
Chapter 4 Data Link Layer Switching
Chapter 4: Routing Concepts
CT1303 LAN Rehab AlFallaj.
Connecting Networks Repeater: physical layer Bridge: data link layer
CNT105 Computer Networking Hardware/Software
Guide to Networking Essentials 7th Edition
Network+ Guide to Networks 6th Edition
Module 8: Ethernet Switching
Network connectivity to the legacy wired LAN
Connectors, Repeaters, Hubs, Bridges, Switches, Routers, NIC’s
Presentation transcript:

Network+ Guide to Networks 5th Edition Chapter 6 Network Hardware

Objectives Identify the functions of LAN connectivity hardware Install, configure, and differentiate between network devices such as, NICs, hubs, bridges, switches, routers, and gateways Explain the advanced features of a switch and understand popular switching techniques, including VLAN management Explain the purposes and properties of routing Describe common IPv4 and IPv6 routing protocols Network+ Guide to Networks, 5th Edition

NICs (Network Interface Cards) Connectivity devices Enable device transmission Transceiver Transmits and receives data Physical layer and Data Link layer functions Issue data signals Assemble and disassemble data frames Interpret physical addressing information Determine right to transmit data Network+ Guide to Networks, 5th Edition

NICs (cont’d.) Smart hardware Do not analyze information Importance Perform prioritization Network management Buffering Traffic-filtering Do not analyze information Added by Layers 3 through 7 OSI model protocols Importance Common to every networking device, network Network+ Guide to Networks, 5th Edition

Types of NICs Before ordering or installing NIC NIC dependencies Know device interface type NIC dependencies Access method Network transmission speed Connector interfaces Compatible motherboard or device type Manufacturer Network+ Guide to Networks, 5th Edition

Types of NICs (cont’d.) Bus Circuit, signaling pathway Motherboard uses to transmit data to computer’s components Memory, processor, hard disk, NIC Differ according to capacity Defined by data path width and clock speed Data path size Parallel bits transmitting at any given time Proportional to attached device’s speed Network+ Guide to Networks, 5th Edition

Internal Bus Standards Expansion slots Multiple electrical contacts on motherboard Allows bus expansion Expansion card (expansion board) Circuit board for additional devices Inserts into expansion slot, establishes electrical connection Device connects to computer’s main circuit or bus Computer centrally controls device Network+ Guide to Networks, 5th Edition

Internal Bus Standards (cont’d.) Multiple bus types PCI bus: most popular expansion board NIC PCI (Peripheral Component Interconnect) 32- or 64-bit bus Clock speeds rated at 33-, 66- or 133-MHz Maximum data transfer rate: 1 Gbps Introduced by Intel (1992) Latest official version: 3.0 (2004) Network+ Guide to Networks, 5th Edition

ISA (Industry Standard Architecture) Figure 6-1 PCI NIC ISA (Industry Standard Architecture) Original PC bus type (early 1980s) Support for 8-bit and 16-bit data path, 4.77-MHz clock PCI bus characteristics Shorter connector length, faster data transmission Compared to previous bus types (ISA) PCs and Macintosh compatible Network+ Guide to Networks, 5th Edition

PCIe (PCI Express) 32- or 64-bit bus Maximum 133-MHz clock speed Figure 6-2 PCIe NIC PCIe (PCI Express) 32- or 64-bit bus Maximum 133-MHz clock speed Transfer rate 500 Mbps per data path (full-duplex transmission) Network+ Guide to Networks, 5th Edition

Internal Bus Standards (cont’d.) PCIe advantages over PCI More efficient data transfer Quality of service distinctions support Error reporting, handling Current PCI software compatible PCIe slots differ from conventional PCI Vary by lanes supported Lane offers full-duplex throughput of 500 Mbps Support up to 16 lanes x16 slot : 8 Gbps throughput Network+ Guide to Networks, 5th Edition

Determining bus type Read documentation Look inside PC case Figure 6-3 A motherboard with multiple expansion slots Determining bus type Read documentation Look inside PC case If more than one expansion slot type: Refer to NIC, PC manufacturers’ guidelines Choose NIC matching most modern bus Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards Attach peripheral devices externally External connection advantage Simple installation Personal Computer Memory Card International Association or PCMCIA Sets standards for externally attached cards Connect virtually any external device type PC Card First standard PCMCIA-standard adapter 16- bit interface running at 8 MHz Network+ Guide to Networks, 5th Edition

CardBus standard (1990s) 32-bit interface running at 33 MHz Figure 6-4 A CardBus NIC Network+ Guide to Networks, 5th Edition CardBus standard (1990s) 32-bit interface running at 33 MHz Matches PCI expansion board standard

Peripheral Bus Standards (cont’d.) ExpressCard standard Many different external devices connect to portable computers 26-pin interface Data transfer rates: 250 Mbps in each direction 500 Mbps total Same data transfer standards as PCIe specification Two sizes 34 mm, 54 mm wide Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) Figure 6-5 ExpressCard modules Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) USB (universal serial bus) port Two USB standards Difference: speed USB 1.1: transfer rate of 12 Mbps USB 2.0: transfer rate of 480 Mbps Future USB 3.0 (SuperSpeed USB) Transfer rate: 4.8 Gbps Network+ Guide to Networks, 5th Edition

Types of NICs (cont’d.) Figure 6-6 A USB NIC Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) Firewire Apple Computer (1980s) IEEE 1394 standard (1995) Traditional Firewire connection: 400 Mbps (max) Newer version: 3 Gbps Connects most peripheral types Connects small network Two or more computers using bus topology Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) FireWire-connected peripherals Similar to USB- and PCMCIA-connected peripherals Simple installation Supported by most modern operating systems Two connector varieties: 4-pin and 6-pin 6-pin connector Two pins supply power Interconnect computers Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) Figure 6-7 FireWire connectors (4-pin and 6-pin) Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) CompactFlash Designed by CompactFlash Association (CFA) Ultrasmall Removable data and input/output device Latest standard: 4.0 Data transfer rate: 133 Mbps Uses Connects devices too small for PCMCIA slots Wireless connections Network+ Guide to Networks, 5th Edition

Peripheral Bus Standards (cont’d.) Figure 6-8 A CompactFlash NIC Network+ Guide to Networks, 5th Edition

On-Board NICs Connect device directly to motherboard On-board ports: mouse, keyboard New computers, laptops Use onboard NICs integrated into motherboard Advantages Saves space Frees expansion slots Network+ Guide to Networks, 5th Edition

Wireless NICs Contain antennas Disadvantages over wire-bound NICs Send, receive signals All bus types supported Disadvantages over wire-bound NICs More expensive Bandwidth and security limitations Network+ Guide to Networks, 5th Edition Figure 6-9 Wireless NICs

Installing NICs Three general steps Install hardware Install NIC software Configure firmware (if necessary) Set of data, instructions Saved to NIC’s ROM (read-only memory) chip Use configuration utility program EEPROM (electrically erasable programmable read- only memory) Apply electrical charges ROM data erased, changed Network+ Guide to Networks, 5th Edition

Installing and Configuring NIC Hardware Read manufacturer’s documentation Install expansion card NIC Verify toolkit contents Unplug computer Ground yourself Open computer case Select slot, insert NIC, attach bracket, verify cables Replace cover, turn on computer Configure NIC software Network+ Guide to Networks, 5th Edition

Figure 6-10 A properly inserted NIC Network+ Guide to Networks, 5th Edition

Installing and Configuring NIC Hardware (cont’d.) Physically install PCMCIA-standard NIC Insert card into PCMCIA slot Figure 6-11 Installing a PCMCIA-standard NIC Network+ Guide to Networks, 5th Edition

Installing and Configuring NIC Hardware (cont’d.) Modern operating systems Do not require restart for PCMCIA-standard adapter Servers, other high-powered computers Install multiple NICs Repeat installation process for additional NIC Choose different slot Network+ Guide to Networks, 5th Edition

Installing and Configuring NIC Software Device driver Software Enables attached device to communicate with operating system Purchased computer Drivers installed Add hardware to computer Must install drivers Network+ Guide to Networks, 5th Edition

Installing and Configuring NIC Software (cont’d.) Operating system built-in drivers Automatically recognize hardware, install drivers Computer startup Device drivers loaded into RAM Computer can communicate with devices Drivers not available from operating system Install and configure NIC software Use operating system interface Network+ Guide to Networks, 5th Edition

Figure 6-12 Windows Vista Update Driver Software dialog box Network+ Guide to Networks, 5th Edition

Interpreting LED Indicators After NIC is installed: Test by transmitting data Assess NIC LEDs for network communication Vary by manufacturer Read documentation Common lights ACT, LNK, LED, TX, RX Network+ Guide to Networks, 5th Edition

IRQ (Interrupt Request) Message to computer Stop and pay attention to something else Interrupt Circuit board wire Device issues voltage to signal request IRQ number Uniquely identifies component to main bus NICs use IRQ 9, 10, or 11 Network+ Guide to Networks, 5th Edition

Table 6-1 IRQ assignments Network+ Guide to Networks, 5th Edition

IRQ (Interrupt Request) (cont’d.) Two devices using same interrupt Resource conflicts, performance problems Many symptoms Must reassign IRQ Through operating system Through adapter’s EEPROM configuration utility Through computer’s CMOS configuration utility Network+ Guide to Networks, 5th Edition

IRQ (Interrupt Request) (cont’d.) CMOS (complementary metal oxide semiconductor) Microchip requiring very little energy to operate Stores settings pertaining to computer’s devices Battery powered Settings saved after computer turned off Information used by BIOS (basic input/output system) BIOS Simple instruction set Enables computer to initially recognize hardware Network+ Guide to Networks, 5th Edition

Memory Range Memory NIC, CPU use for exchanging, buffering data Some are reserved for specific devices NICS High memory area (A0000–FFFFF range) Manufacturers prefer certain ranges Resource conflicts less likely (than IRQ settings) Network+ Guide to Networks, 5th Edition

Base I/O Port Memory area Cannot be used by other devices Channel for moving data between NIC and CPU Cannot be used by other devices NICs use two channel memory ranges Base I/O port settings identify beginning of each range Network+ Guide to Networks, 5th Edition

Firmware Settings Contain NIC’s transmission characteristics Combination EEPROM chip on NIC and data it holds Change firmware Change EEPROM chip Requires bootable CD-ROM Configuration, install utility shipped with NIC Network+ Guide to Networks, 5th Edition

Firmware Settings (cont’d.) Configuration utility View IRQ, I/O port, base memory, node address Change settings Perform diagnostics NIC’s physical components, connectivity Loopback plug (loopback adapter) Outgoing signals redirected into computer for testing Use with loopback test Network+ Guide to Networks, 5th Edition

Choosing the Right NIC Considerations Compatibility with existing system Network bus type, access method, connector types, transmission speed Drivers available Operating system, hardware Subtle differences Affecting network performance Important for server Network+ Guide to Networks, 5th Edition

Table 6-2 NIC characteristics Network+ Guide to Networks, 5th Edition

Repeaters and Hubs Repeater Simplest connectivity device regenerating signals Operates at Physical layer Has no means to interpret data Limited scope One input port, one output port Receives and repeats single data stream Suitable for bus topology networks Extend network inexpensively Rarely used on modern networks Limitations; other devices decreasing costs Network+ Guide to Networks, 5th Edition

Repeaters and Hubs (cont’d.) Repeater with more than one output port Multiple data ports, uplink port Repeats signal in broadcast fashion Operates at Physical layer Ethernet network hub Star or star-based hybrid central connection point Connect workstations, print servers, switches, file servers, other devices Network+ Guide to Networks, 5th Edition

Repeaters and Hubs (cont’d) Hub (cont’d.) Devices share same bandwidth amount, collision domain More nodes leads to transmission errors, slow performance Placement in network varies Simplest: stand-alone workgroup hub Different hub to each small workgroup Placement must adhering to maximum segment and length limitations Network+ Guide to Networks, 5th Edition

Repeaters and Hubs (cont’d) Figure 6-13 Hubs in a network design Network+ Guide to Networks, 5th Edition

Hub (cont’d.) Hubs vary according to: Figure 6-14 A stand-alone hub Hub (cont’d.) Hubs vary according to: Supported media type, data transmission speeds Passive hubs, Intelligent hubs (managed hubs), Stand-alone hubs (workgroup hubs) Replaced by switches routers Limited features Merely repeat signals Network+ Guide to Networks, 5th Edition

Bridges Connects two network segments Operate at Data Link layer Analyze incoming frames and decide where to send Based on frame’s MAC address Operate at Data Link layer Single input port and single output port Interpret physical addressing information Advantages over repeaters and hubs Protocol independence Add length beyond maximum segments limits Improve network performance Network+ Guide to Networks, 5th Edition

Disadvantage compared to repeaters and hubs Figure 6-15 A bridge’s use of a filtering database Network+ Guide to Networks, 5th Edition Disadvantage compared to repeaters and hubs Longer to transmit data Filtering database (forwarding table) Used in decision making Filter or forward

Bridges (cont’d.) New bridge installation Today bridges nearly extinct Learn network Discover destination packet addresses Record in filtering database Destination node’s MAC address Associated port All network nodes discovered over time Today bridges nearly extinct Improved router and switch speed, functionality Lowered router and switch cost Network+ Guide to Networks, 5th Edition

Switches Subdivide network Operates at Data Link layer (traditional) Smaller logical pieces, segments Operates at Data Link layer (traditional) Operate at layers 3 and 4 (advanced) Interpret MAC address information Components Internal processor, operating system, memory, several ports Network+ Guide to Networks, 5th Edition

Multiport switch advantages over bridge Figure 6-16 Switches Multiport switch advantages over bridge Better bandwidth use, more cost-efficient Each port acts like a bridge Each device effectively receives own dedicated channel Ethernet perspective Dedicated channel represents collision domain Network+ Guide to Networks, 5th Edition

Switches (cont’d.) Historically Disadvantages Switches replaced hubs, eased congestion, provided better security, performance Disadvantages Can become overwhelmed despite buffers Cannot prevent data loss UDP collisions mount: network traffic halts Switches replaced workgroup hubs Decreased cost, easy installation, configuration, Separate traffic according to port Network+ Guide to Networks, 5th Edition

Installing a Switch Follow manufacturer’s guidelines General steps (assume Cat 5 or better UTP) Verify switch placement Turn on switch Verify lights, self power tests Configure (if necessary) Connect NIC to a switch port (repeat for all nodes) After all nodes connected, turn on nodes Connect switch to larger network (optional) Network+ Guide to Networks, 5th Edition

Installing a Switch (cont’d.) Figure 6-17 Connecting a workstation to a switch Figure 6-18 A switch on a small network Network+ Guide to Networks, 5th Edition

Switching Methods Difference in switches Four switching modes exist Incoming frames interpretation Frame forwarding decisions making Four switching modes exist Two basic methods discussed Cut-Through Mode Store-and-Forward Mode Network+ Guide to Networks, 5th Edition

Cut-Through Mode Switch reads frame’s header Forwarding decision made before receiving entire packet Uses frame header: first 14 bytes contains destination MAC address Cannot verify data integrity using frame check sequence Can detect runts Erroneously shortened packets Runt detected: wait for integrity check Network+ Guide to Networks, 5th Edition

Cut-Through Mode (cont’d.) Cannot detect corrupt packets May propagate flawed packets Advantage Speed Disadvantage Data buffering (switch flooded with traffic) Best use Small workgroups needing speed Low number of devices Network+ Guide to Networks, 5th Edition

Store-and-Forward Mode Switch reads entire data frame into memory Checks for accuracy before transmitting information Advantage over cut-through mode Transmit data more accurately Disadvantage over cut-through mode More time consuming Best use Larger LAN environments; mixed environments Can transfer data between segments running different transmission speeds Network+ Guide to Networks, 5th Edition

VLANs and Trunking VLANs (virtual local area networks) Logically separate networks within networks Groups ports into broadcast domain Broadcast domain (subnet) Port combination making a Layer 2 segment Ports rely on layer 2 device to forward broadcast frames Collision domain Ports in same broadcast domain Do not share single channel Network+ Guide to Networks, 5th Edition

VLANs and Trunking (cont’d.) Figure 6-19 A simple VLAN design Network+ Guide to Networks, 5th Edition

VLANs and Trunking (cont’d.) Advantage of VLANs Flexible Ports from multiple switches or segments Use any end node type Reasons for using VLAN Separating user groups Isolating connections Identifying priority device groups Grouping legacy protocol devices Network+ Guide to Networks, 5th Edition

VLANs and Trunking (cont’d.) VLAN creation Configuring switch software Manually through configuration utility Automatically using VLAN software tool Critical step Indicate to which VLAN each port belongs Additional specifications Security parameters, filtering instructions, port performance requirements, network addressing and management options Maintain VLAN by switch software Network+ Guide to Networks, 5th Edition

Figure 6-20 Result of the show vlans command on a Cisco switch Network+ Guide to Networks, 5th Edition

VLANs and Trunking (cont’d.) Potential VLAN issues Cutting off group from rest of network Correct by using router Trunking Switch’s interface carries traffic of multiple VLANs Trunk Single physical connection between devices Many logical VLANs transmit, receive data VLAN data separation Frame contains VLAN identifier in header Network+ Guide to Networks, 5th Edition

VLANs and Trunking (cont’d.) Advantage of VLAN trunking Economical interface usage Switches make efficient use of processing capabilities VLAN configuration Can be complex Requires careful planning Ensure users and devices can exchange data Ensure VLAN switch properly interacts with other devices Network+ Guide to Networks, 5th Edition

STP (Spanning Tree Protocol) IEEE standard 802.1D Operates in Data Link layer Prevents traffic loops Calculating paths avoiding potential loops Artificially blocking links completing loop Three steps Select root bridge based on Bridge ID Examine possible paths between network bridge and root bridge Disables links not part of shortest path Network+ Guide to Networks, 5th Edition

STP (cont’d.) Figure 6-21 Enterprise-wide switched network Network+ Guide to Networks, 5th Edition

STP (cont’d.) Figure 6-22 STP-selected paths on a switched network Network+ Guide to Networks, 5th Edition

STP (cont’d.) History Cisco and Extreme Networks Introduced in 1980s Original STP too slow RSTP (Rapid Spanning Tree Protocol) Newer version IEEE’s 802.1w standard Cisco and Extreme Networks Proprietary versions No enabling or configuration needed Included in switch operating software May alter default priorities Network+ Guide to Networks, 5th Edition

Content and Multilayer Switches Layer 3 switch (routing switch) Interprets Layer 3 data Layer 4 switch Interprets Layer 4 data Content switch (application switch) Interprets Layer 4 through Layer 7 data Advantages Advanced filtering, statistics keeping, security functions Network+ Guide to Networks, 5th Edition

Content and Multilayer Switches (cont’d.) Disadvantages No agreed upon standard Layer 3 and Layer 4 switch features vary widely Distinguishing between Layer 3 and Layer 4 switch Manufacturer dependent Higher-layer switches Three times Layer 2 switches Used in backbone Network+ Guide to Networks, 5th Edition

Routers Multiport connectivity device Directs data between network nodes Integrates LANs and WANs Different transmission speeds, protocols Operate at Network layer (Layer 3) Directs data from one segment or network to another Logical addressing Protocol dependent Slower than switches and bridges Need to interpret Layers 3 and higher information Network+ Guide to Networks, 5th Edition

Routers (cont’d.) Traditional stand-alone LAN routers New niche Being replaced by Layer 3 routing switches New niche Specialized applications Linking large Internet nodes Completing digitized telephone calls Network+ Guide to Networks, 5th Edition

Router Characteristics and Functions Intelligence Tracks node location Determine shortest, fastest path between two nodes Connects dissimilar network types Large LANs and WANs Routers indispensible Router components Internal processor, operating system, memory, input and output jacks, management control interface Network+ Guide to Networks, 5th Edition

Holding different interface cards, other devices Inexpensive routers Figure 6-23 Routers Modular router Multiple slots Holding different interface cards, other devices Inexpensive routers Home, small office use Network+ Guide to Networks, 5th Edition

Router Characteristics and Functions (cont’d.) Router tasks Connect dissimilar networks Interpret Layer 3 addressing Determine best data path Reroute traffic Optional functions Filter broadcast transmissions Enable custom segregation, security Support simultaneous connectivity Provide fault tolerance Monitor network traffic, diagnose problems Network+ Guide to Networks, 5th Edition

Router Characteristics and Functions (cont’d.) Directing network data Static routing Administrator programs specific paths between nodes Dynamic routing Router automatically calculates best path between two nodes Routing table Installation Simple: small office, home LANs Challenging: sizeable networks Network+ Guide to Networks, 5th Edition

Router Characteristics and Functions (cont’d.) Figure 6-24 The placement of routers on a LAN Network+ Guide to Networks, 5th Edition

Routing Protocols Best path Most efficient route from one node to another Dependent on: Hops between nodes Current network activity Unavailable link Network transmission speed Topology Determined by routing protocol Network+ Guide to Networks, 5th Edition

Routing Protocols (cont’d.) Router communication Collects current network status data Contribute to best path selection Routing table creation Router convergence time Time router takes to recognize best path Change or network outage event Distinguishing feature Overhead; burden on network to support routing protocol Network+ Guide to Networks, 5th Edition

Distance-Vector: RIP, RIPv2, BGP Distance-vector routing protocols Determine best route based on distance to destination Factors Hops, latency, network traffic conditions RIP (Routing Information Protocol) Only factors in number of hops between nodes Limits 15 hops Interior routing protocol Slow and less secure Network+ Guide to Networks, 5th Edition

Distance-Vector: RIP, RIPv2, BGP (cont’d.) RIPv2 (Routing Information Protocol Version 2) Generates less broadcast traffic, more secure Cannot exceed 15 hops Less commonly used BGP (Border Gateway Protocol) Communicates using BGP-specific messages Many factors determine best paths Configurable to follow policies Most complex (choice for Internet traffic) Network+ Guide to Networks, 5th Edition

Link-State: OSPF, IS-IS Link-state routing protocol Routers share information Each router independently maps network, determines best path OSPF (Open Shortest Path First) Interior or border router use No hop limit Complex algorithm for determining best paths Each OSPF router Maintains database containing other routers’ links Network+ Guide to Networks, 5th Edition

Link-State: OSPF, IS-IS (cont’d.) IS-IS (Intermediate System to Intermediate System) Codified by ISO Interior routers only Supports two Layer 3 protocols IP ISO-specific protocol Less common than OSPF Network+ Guide to Networks, 5th Edition

Hybrid: EIGRP Hybrid Link-state and distance-vector characteristics EIGRP (Enhanced Interior Gateway Routing Protocol) Most popular Cisco network routers only EIGRP benefits Fast convergence time, low network overhead Easier to configure and less CPU-intensive than OSPF Supports multiple protocols Accommodates very large, heterogeneous networks Network+ Guide to Networks, 5th Edition

Gateways and Other Multifunction Devices Combinations of networking hardware and software Connecting two dissimilar networks Connect two systems using different formatting, communications protocols, architecture Repackages information Reside on servers, microcomputers, connectivity devices, mainframes Popular gateways E-mail gateway, Internet gateway, LAN gateway, Voice/data gateway, Firewall Network+ Guide to Networks, 5th Edition

Summary NIC interface cards Repeater and hubs Bridges Switches Types, installation, testing, IRQ use, Base I/O port use, firmware settings, selection Repeater and hubs Bridges Switches Installation, switching methods, VLANs and trunking, STP (Spanning Tree Protocol), Content and Multilayer Switches Router characteristics and functions, protocols Gateways and other multifunction devices Network+ Guide to Networks, 5th Edition