TOPIC 3: DESIGN AND ANALYSIS OF SHALLOW FOUNDATION

Slides:

Advertisements

Similar presentations

SUB-STRUCTURE foundations.

Advertisements

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Check Beam Shear.

Design Of Foundation for a Commercial and Residential Building

Chp12- Footings.

Summary Sheet Session Number : Date : Subject Expert : Dr. M.C. Nataraja Professor Department of Civil Engineering, S.J. College of Engineering,

Lecture 9 - Flexure June 20, 2003 CVEN 444.

SEMINAR IN ADVANCED STRUCTURE analysis and design of box culvert

Overview Waffle Slab.

Design of Mat Foundations

SHEAR IN BEAMS. SHEAR IN BEAMS Example (4.1): A rectangular beam has the dimensions shown in Figure 4.12.a and is loaded with a 40 ton concentrated.

Design of Cantilevered Retaining Walls

Foundation System Design for Al Nimmer Commercial Building

Chp.12 Cont. – Examples to design Footings

Foundation Systems.

Reinforced Concrete Design II

Reinforced Concrete Design II

FOUNDATION The foundation of a structure is the lowest part of the sub-structure interfering with the soil and the structure. It consists of some structural.

Stresses Found In Structural Members. Forces Acting Simply Supported Beam 1.Bending.

TOPIC 2: TYPES OF FOUNDATION

FOUNDATION DESIGN.

ERT352 FARM STRUCTURES FOUNDATION DESIGN

Australian Geomechanics Society Mini-symposium Sydney October 2005 Soil Loads on Cut and Cover Tunnels Under High Fills Doug Jenkins Interactive Design.

Commercial Foundations

SHEAR IN BEAMS. SHEAR IN BEAMS Introduction Loads applied to beams produce bending moments, shearing forces, as shown, and in some cases torques. Beams.

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Details of Construction Lecture-2 “Shallow Foundation”

STRUT & TIE MODELS (S-T-M)

Plain & Reinforced Concrete-1 CE-313

BEAMS AND COLUMNS.

Villanova University Dept. of Civil & Environmental Engineering CEE Capstone II Structural Engineering 1 CEE Capstone II Structural Engineering.

Reading Structural Drawings

FOOTINGS. FOOTINGS Introduction Footings are structural elements that transmit column or wall loads to the underlying soil below the structure. Footings.

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Tulkarem Multipurpose Sport Hall Prepared by: Moatasem Ghanim Abdul-Rahman Alsaabneh Malek Salatneh Supervisor: Dr. Shaker Albitar.

Graduation project: Jaba’a Institution Supervised by: Dr. Riyad Abdel-Karim Awad Dr.Sameer El Helw Dr.Sameer El Helw By :Fadi Hamaydi.

An-Najah National University Faculty Of Engineering Civil Engineering Department Al-Najjar Building Footing Design Systems Alternative Prepared by : Mohammed.

 The site is located in Tulkarem city.  The building consists of seven stories, and the area of each stories is about 700 m 2, the aim of this research.

1 Foundations and retaining walls.

 General description of the project.  Structural system.  Geotechnical conditions of the site.  Design of two types of foundation.

Isolated footing with axial load and moment

CE 482 Examples.

By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. Reinforced Concrete Design-6 Shear Design of Beams.

GLE/CEE 330: Soil Mechanics Bearing Capacity of Shallow Footings

SANKALCHAND PATEL COLLEGE OF ENGINEERING,

جامعة الكوفة كلية الهندسة / قم الهندسة المدنية / المرحلة الثالثة Retaining Walls إعداد المهندس ليث عبد الرسول الأسدي.

AR362 - Structural Systems In Architecture IV Lecture : Foundations

GLE/CEE 330: Soil Mechanics Introduction to Foundation Engineering

INSTITUTE OF TECHNOLOGY

سایت جامع دانشجویان و مهندسین عمران Footing Design

AHSANULLAH UNIVERSITY OF SCIENCE & TECHNOLOGY DEPT

BHAGWAN MAHAVIR COLLEGE OF ENGINEERING AND TECHNOLOGY

An-Najah National University Faculty of Engineering

DR. JIVRAJ MEHTA INSTITUTE OF TECHNOLOGY

SEMINAR ON FOOTING.

Design of shallow foundations for optical and nursing faculty

UNIT-IV SHEAR,TORSION AND BOND.

FOR 5TH SEMESTER DIPLOMA IN CIVIL ENGINEERING

Graduation Project Seminar

Structure II Course Code: ARCH 209 Dr. Aeid A. Abdulrazeg.

Reinforced Concrete Design-6

Structure II Course Code: ARCH 209 Dr. Aeid A. Abdulrazeg

An-Najah National University

An-Najah National University

OUTLINES - location & Description. Material properties.

Structural Design I Course Code: CIVL312 Dr. Aeid A. Abdulrazeg.

Presentation transcript:

TOPIC 3: DESIGN AND ANALYSIS OF SHALLOW FOUNDATION WEEK 8 CONSTRUCTION DETAILS FOR SHALLOW FOUNDATION STRUCTURAL DESIGN OF SHALLOW FOUNDATION

Learning Outcomes Student should be able to: Specify details for shallow foundation construction (CO2-PO10) Determine the maximum bending moment and shear stress for RC design (CO2-PO10)

Construction Drawings Raft Foundation Pad Footing Details on platform, footing sizes, Reinforcement details, design bearing capacity

RC Design for Pad Foundation Determine base area of foundation by dividing column load by the allowable bearing pressure on the soil. Determine overall depth of foundation required by punching shear, based on column load only. Select type of foundation: simple flat or sloping upper surface. Check dimension by computing beam shear stress at critical section, on the basis that diagonal shear reinforcements should not be provided. Compute bending moment and design the reinforcement. Check bond stresses in steel.

Shear stress at the Critical Section Of 1.5d

Maximum Bending Moment