AO Series 10 Illuminator pattern

Slides:

Advertisements

Similar presentations

Sectional Views Copyright © 2003 Glencoe/McGraw-Hill.

Advertisements

How To Catch A Swarm Using Buckets. Take 2 plastic buckets and cut a large matching hole in the bottom of each. Using screen wire, preferably 1/8 hardware.

MO-735 Overlock Dealer Training CLICK.

New Mexico FFA Agricultural Mechanics Career Development Event Electric Power.

Jennifer Wolfe NAEA CONVENTION Baltimore, MD 2010.

Stable Rise – Fixed Bracket / Stationary Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH

Flexible Manufacturing Common Sheet Metal Seams Copyright © Texas Education Agency, All rights reserved.

Optical Manufacturing Solutions 1 Probe Assembly.

Lock Replacement. Step 1: Cut insulation behind lock mechanism.

Chrictmas decoration. How to make tree decorations made of wool.

Electrical Wiring Circuit Board Project. STEP 1 - Identify all Parts of the Project Saw Drill Driver w/ bits Drill w/bits (not pictured) #2 Phillips Screwdriver.

The Fits -All mount TM UNIVERSAL ELECTRONICS MOUNTING BRACKET The Fits -All mount TM Haltof Product Design, inc. This presentation was part of our Fits-ALL.

Living with the lab Prototyping with Sheet Metal.

Air tank installation instructions Included parts: Raw aluminum air tank bracket 5/16-18 button head bolts (qty 4) M8x1.25 button head bolts (qty 4) M8.

Full Ribs to Rear Spar Parts Layout July 6, H2-2, Horizontal Stab Rear Spar with upper and lower doublers.

This is the 8’ metal bending brake we used. Since I forgot to take pictures, the pictures I use in this presentation to describe what I’m doing are from.

Making a trap cage. You need plastic bottles, wire, string, a plastic bag and tools.

Router Safety. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate.

Update on Model/Mock Cavity Robyn Madrak 02/03/2015.

TOUGHENED GLASS FIBER REINFORCED BODY TOUGHENED GLASS FIBER REINFORCED BODY ONE PIECE BODY FOR OPTIMUM INTEGRITY ONE PIECE BODY FOR OPTIMUM INTEGRITY STANDARD.

Chapter 4: Sheet Metal Forming

Making A Motor Exploring the Magic of Electricity.

Mounting arrangement for the Solid Absorber. This contains mounting arrangement for:- 1. Handling and lifting from manufacturer’s place to RAL; 2. For.

Bob Howard 10/22/2011.  How many connectors do you need ◦ Max DC/Servo Motor Controllers is 4 so use 4  How long should the connectors be ◦

META-MECHANICS INSPIRED BY JEAN TINGUELY SWISS SCULPT0R WORKED IN FRANCE

Masonry Tools Flip Book Instructions. Step 1: You need 5 pieces of paper. Lined or plain will work. You also need a pen and a ruler. Draw a line down.

Chapter 11, Section 3. Interior Installation Installing a curtain rod Mounting Venetian blinds Mounting a window shade Hanging a picture.

AIR CONDITIONING (COOLING)

116- Trade Skills Hems, Edges, and Seams.

School Name Date Volunteer Name Electric Generator SEEDKIT Workshop.

SCREWDRIVERS & PLIERS.

The Makeup of the Knife. Parts of the Knife A knife is constructed of several parts Each part determines how the knife feels in the chef’s hand and how.

Teen Living Objective Fashion Construction Teen Living Objective

Wire and spinning magnets Reference: Original Authur: William Beaty 1996.

ENGR 241 – Introduction To Manufacturing

Contributed by: Integrated Teaching and Learning Program, College of Engineering, University of Colorado at Boulder.

By: Joe M. Searcy Tools Needed  Small Flat-Tip Screwdriver (Taped up with masking tape)  Socket set (or nut drivers), sizes  ¼”

SHEET METAL FORMING PROCESS / PRESS WORKING OF SHEET METALS

Metalwork. Information about Metalwork Quick Facts Metalwork is a Three Year Course. It ends with the Junior Certificate Exam in 3rd Yr. There is a Higher.

1 Remove seat from vehicle and remove seat trim cover.

How to mark out, cut, shape and finish. Marking Out For straight lines use a ‘scriber’ and an ‘engineers square’

SHEET METAL process.

LAB #10. Governor Control Arm Using a 10mm socket install the two bolts that hold the governor control arm. Finger tighten then torque to 100 “#

Plenum Seal From Above This photo shows a Cross-over connection, below a plenum from above. The arrows point to a large gap. Close up of large.

Proper Use of Hand Tools. Wrenches Never use a pipe extension or “cheaters” Select the right opening for the nut Always pull the wrench handle when turning.

ELECTRIC VEHICLE PROJECT CAR BUILDING PROCEDURES BY: PIERRE PEASHA CENTENNIAL HIGH SCHOOL BAKERSFIELD, CA.

Unico Tips and Tricks. First Steps Layout and material list to be done by the salesman Wear Hospital Style Booties, if working in a non-drop cloth area.

Rapid Change Technology The following is a presentation to aid Technicians in the replacement of the Rapid Change Technology Block.

AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.

Additional Hand Tools Harding High School Mr. Pottkotter & Mr. Robinson.

Genuine N1. Conversion Installation manual LC 120 5D 2003

Assembly of steering.

Flexible Manufacturing

Electrical Wiring Circuit Board Project

Sheet Metal Forming Processes

How to make a simple monkey puppet

Basic Foldable Shapes.

Starter Get our your book and turn to our next available page.

T400 Motor Replacement.

Making a trap cage.

Building a Nightstand Woods 1 Final Project Step #1

Engineering Applications Level 1 Explain Pattern Development

The Leica Mount for a CP 4500 IMPORTANT NOTES

SHEET F20-06 t-deck T11-01 vert-tail W22-01L wingtip F20-03R

Exploring the Magic of Electricity

The Leica Mount for a CP 4500 IMPORTANT NOTES

Caring Hands Cocoon Page 1 of 5 15” cocoon 2” test square 13” cocoon

Pembrey at war – Lesson 4.

Presentation transcript:

AO Series 10 Illuminator pattern with cover. Replaces Mirror mount. 3 4 2 2 5 1 1 5 This cover could be wider if you Have more room.

Cardboard mock up of full cover pattern. Cover could be larger Than pattern shows- but I drew ‘tight’ so I could get two from the Wal Mart cookie sheet. Hand holding a CF ballast, and ballast mounted. Ballast covers are removed, and the spool flanges trimmed just bit, to fit.

5 2 1 AO Series 10 Illuminator Cutting patterns- One piece base, partial cover Replaces mirror mount in base. 3 4 2 1 5

Cardboard mock up w/ cover in place. Note that tail of cover goes under fold in the back- so offset the bend-over on the back, to allow clearance. Cover attaches with sheet metal screw(s) in the back, and in front, the tabs catch the mirror mount screws. An example of the earlier pattern cut and bent up. Ballast can be under cover, but some insulated wiring is exposed. Ballast should be used with it’s cover.