INSTRUCTOR © 2017, John R. Fanchi All rights reserved. No part of this manual may be reproduced in any form without the express written permission of the author. © 2004 John R. Fanchi All rights reserved. Do not copy or distribute.

To the Instructor The set of files here are designed to help you prepare lectures for your own course using the text Introduction to Petroleum Engineering, J.R. Fanchi and R.L. Christiansen (Wiley, 2017) File format is kept simple so that you can customize the files with relative ease using your own style. You will need to supplement the files to complete the presentation topics.

WELL COMPLETIONS © 2017, John R. Fanchi All rights reserved. No part of this manual may be reproduced in any form without the express written permission of the author. © 2004 John R. Fanchi All rights reserved. Do not copy or distribute.

Outline Casing Cementing Types of Completions Perforating Workovers Stimulation Hydraulic Fracturing Artificial Lift Homework: IPE Ch. 10

CASING © 2004 John R. Fanchi All rights reserved. Do not copy or distribute.

Well Completion Procedure to Prepare Well for Production Decision: complete or plug & abandon Issues to consider Which formations should be isolated? Open hole or cased hole? Perforating design? Stimulate? (if necessary) Sand Control? (if necessary) Test well?

Casing Design Keep hole from collapsing over its life Complete production conduit from reservoir to surface Protect shallow zones from heavy mud weights Allow for future well stimulation e.g. casing must withstand pressure of frac treatment

Wellbore

Wellbore Diagram for Vertical Well Concentration (ppm) Fresh water < 1,000 Brackish water 1,000 to 35,000 Brine > 35,000 Source: Hyne (2012, pg 18)

Casing Strings Surface Surface + Production + Intermediate

CEMENTING

Cement Bond Log Uses acoustic signals to detect cement behind pipe Determines quality of bond good bond, poor bond, no bond Determines top of cement Requires interpretation, so user beware

TYPES OF COMPLETIONS

Types of Completions Cased Hole Open Hole Liners and Tiebacks Tubingless Dual zone and commingled zones

Sand Control Suppose formation sand (e.g. from unconsolidated rock) flows into wellbore Plugs pores and restricts or stops fluid flow Increases damage to tubing Causes surface equipment to sometimes plug up Methods to Control Sand Screening with gravel and metal screens Chemical consolidation, e.g. resin coating Frac Pacs Sand control usually causes reduction in production rate

PERFORATING

Perforating Purpose of Perforating Create passage for oil/gas to flow into wellbore Position perforating gun Blast holes through pipe and cement into target formation Flow into wellbore Source: www.geomore.com, accessed April 2013

Perforating Design Hole size & shot density (holes per foot) are basic to design e.g. 4 shots/foot is fairly dense Design should include estimate of stimulation and production rates Casing may be pre-perforated or slotted before running Must design for intervals of interest

Formation Damage Producing rock is altered in a way that reduces flow of hydrocarbons into wellbore Types of Damage Fluid damage Drilling mud filtrate or other fluid fills pore space Causes changes in perm and relative perm Solids damage Fines plug up pore spaces, e.g. mud cake Scale buildup on perfs and in formation

WORKOVERS

Workover Repair or replace equipment Sucker rod string Downhole pump Tubing Cleanout well Sand Scale (salt) Wax

STIMULATION

Well Stimulation Purpose: Increase productivity Methods Explosive Fracturing Acidizing Hydraulic Fracturing

Acidizing Acid “soak” near wellbore can remove damage Acid frac (deep penetration) in limestones Limestone will dissolve Create improved pathways; e.g. Middle East

Types of Acid HCL common Other types Typically use about 1,500 gals of 15% HCl Aids in frac after clearing perforations and borehole wall Must be careful when producing spent acid Excellent for dissolving lime scale buildup (CaCO3) Other types Citric – weak clean up acid Hydrofluoric acid (difficult to handle; dissolves glass)

HYDRAULIC FRACTURING Near Mansfield, TX

Orientation of three principal stresses Wellbore Stress Sv Sv Sh Sh SH SH Vertical Horizontal Orientation of three principal stresses

Directions of Sh and SH Borehole Breakout: Determine direction of Sh using dipmeter and caliper logs in previously drilled wellbores σhmax σhmin Plan View σv Stress Orientation Observe wellbore failure in direction of σhmin σhmax is transverse to σhmin Plan well azimuth in direction of minimum horizontal stress σhmin σv > σhmax > σhmin

Gel Frac Gel fracs combine water and polymer Thicken injected fluid so it can carry significant amount of proppants into formation Injection pressure must exceed fracture pressure

Slick Water Frac Slick water fracs combine water with a friction-reducing chemical additive The additive allows water to be pumped faster into the formation. Water fracs do not use any polymers to thicken so the amount of proppant used is significantly less than that of gels. Slick water fracs work very well in low-permeability reservoirs Injection pressure must exceed fracture pressure

Proppant Blend proppant (sand, beads, etc.) with water Proppant stays in fracture to prevent it from closing (healing) after pumping ceases Proppant must be strong enough not to collapse (or be crushed) under forces trying to heal fracture Propped fracture becomes flow conduit Propped frac should increase rate of fluid flow to producer

Approximate Closure Pressure Limits for Proppant Categories Closure Pressure Limit, psi Temperature Limit, ˚F Sand 4,000 NA Resin-Coated Sand 8,000 250 Intermediate Strength Ceramic 10,000 High Strength Ceramic >12,000 © 2004 John R. Fanchi All rights reserved. Do not copy or distribute.

Water Production from a Shale Well Influenced by Formation rock and fluid Fracturing fluid Typical constituents Suspended solids Dissolved solids Organics, e.g. hydrocarbons Residual-fracturing-fluid chemicals Disposition of produced water Recycle Disposal

Video Hydraulic Fracturing Marathon Youtube video (6.5 mins) http://www.youtube.com/watch?v=VY34PQUiwOQ&feature=player_embedded# Baker-Hughes Composite Plug Youtube video (7 mins) http://www.youtube.com/watch?v=oPgZnZqp87k

Classification System for Fracturing Treatment Types Fracture Treatment Definition (Types 1 to 6 transport proppant into hydraulic fracture) 1. Conventional Use a gelling agent and one or more crosslinkers 2. Water Frac Use a friction reducer, a gelling agent, or a viscoelastic surfactant 3. Hybrid Use combination of friction reducer, gelling agent, acid-gelling agent, or crosslinker(s) 4. Energized Incorporate an energizer, normally N2 or CO2, into base fluid to generate foam 5. Acid Frac Use a gelled-acid base fluid to etch away formation rock and transport proppant 6. Gas Frac Use a gas, normally propane, as base fluid to transport proppant 7. Matrix Acidizing Use acid to etch away formation rock to increase oil or gas well productivity Source: SPE 163875, JPT (Mar 2014), pg. 110 © 2004 John R. Fanchi All rights reserved. Do not copy or distribute.

Typical Fracture Treatment Pre-frac testing gives rate and pressure data Pump job in stages Lead in – no proppant mixed in Followed by gelled water with proppant in low concentration – 1 or 2 ppg Followed by more stages of gelled water with increasing concentrations of proppant Tail in with high concentration at end up to 7-8 ppg

Planning the Job Determine type of fluid Gelled, slick, foam, condensate, CO2. Types of gelling agents, friction reducers, bactericides, corrosion inhibiters and other additives May use foam, oil or condensate instead of water Determine amount of water and proppant to be pumped Rate of treatment – bbls / minute Estimate rate and pressure needed to exceed frac gradient Desired rate determines horsepower required Consider safety, logistics and contingencies

Fracking may not be successful Source: JPT (Mar 2014), pg. 87 © 2004 John R. Fanchi All rights reserved. Do not copy or distribute.

Fracture Treatment Issues Size of Job Small Job = 30,000 gals and 50,000 lbs proppant Large job = 500,000 gals and 1,000,000 lbs proppant Deep wells Sand proppant can be crushed in deep treatments Need special proppant (e.g. bauxite) Should fluid be pumped down casing or tubing? Typically casing ID > tubing ID Casing gives better rate but at lower pressures Tubing allows high pressures but low rate

Video Hydraulic Fracturing http://www.youtube.com/watch?v=mJGihwJFIWU Western Energy footage, 7.5 minutes IPAMS International Petroleum Association of Mountain States

Stimulation Guide Natural Completion Stimulation not needed, e.g. undamaged, high quality rocks such as the Gulf Coast Matrix Acidizing Cleans up perforating debris & formation damage Acid Frac Primarily in limestones Deep penetration (>100’ or more); etches out channels Hydraulic Fracturing Low permeability formations

ARTIFICIAL LIFT

Production Artificial Lift Common Methods Useful when reservoir pressure unable to push oil to surface Recognize need when oil rate declines unexpectedly Common Methods Pumping Unit Submersible pump Gas Lift Time Producing Rate Projected Actual Is something wrong?

Factors that Impact Artificial Lift Reliability Installation practices Operating practices Equipment qualification and testing Material selection Sizing and selection of equipment New vs used equipment Quality of manufacturing Quality of completion Fit for purpose design Relationship between manufacturer, supplier, and vendor Source: S. Noonan table, JPT, pg. 62, March 2015

QUESTIONS?

SUPPLEMENT