V VENTURI SEPARATORS STEAM.

Slides:



Advertisements
Similar presentations
en l ’an ans d ’expérience sur la vapeur
Advertisements

An Introduction To Marine Steam Propulsion Plant [Source: US Navy]
Antero Punttila Analyzing most typical energy saving measures Energy Efficiency of Steam and Condensate Systems Antero Punttila, Motiva Oy.
Main Steam Cycle Let the fun begin….
ENERGY CONVERSION MME 9617A Eric Savory
Rankine Cycle Figures from Cengel and Boles, Thermodynamics, An Engineering Approach, 6th ed., McGraw Hill, 2008.
Design &Types of Steam Turbines
Fluid Mechanics.
Watertube Boiler.
1 Lec 24: Rankine cycle reheat, deviations, efficiency increases, viscosity, introduction to fluid flow.
Department of Mechanical Engineering ME 322 – Mechanical Engineering Thermodynamics Lecture 25 Comparison to Carnot’s Heat Engine Effects of Boiling and.
Chapter 1 VAPOR AND COMBINED POWER CYCLES
“Energy Efficiency Guide for Industry in Asia”
Steam Power Plant.
Fluid Mechanics 06. Energy, Work and Power Work:- Work is force acting through a distance when the force is parallel to the direction of motion. Energy:-
A Vapor Power Cycle Boiler T Turbine Compressor (pump) Heat exchanger
STEAM CONDENSERS.
Irreversible Flow from Turbine Exit to Condenser
Lesson 7 Steam Power Plant.
STEAM HEATING.
Water piping design.
Vapor and Combined Power Cycles (2)
STUDY OF BOILER’S ACCESSORIES
Prof. D.N. Reddy Director Centre for Energy Technology University College of Engineering Osmania University.
Clean and Pure steam in the Biopharm industry
ME 414 – TEAM #1 JENNIFER HACKER JESSE KENDALL CHRISTOPHER ROGERS BRANDON RODRIGUEZ ALEK VANLUCHENE Heat Exchanger Design.
Heat Exchangers This is session 19 in curriculum manual.
Heat Transfer Equations For “thin walled” tubes, A i = A o.
Engineer Training Cooler TJ8300 / TJ8500 Cooler. Engineer Training Cooler TJ8300 / TJ8500 Confidential 2 Introduction.
Plant Utility System (TKK-2210) 14/15 Semester 4 Instructor: Rama Oktavian Office Hr.: M-F
A Vapor Power Cycle Boiler T Turbine Compressor (pump) Heat exchanger
STEAM TURBINE POWER CYCLES. The vast majority of electrical generating plants are variations of vapour power plants in which water is the working fluid.
Clark Reliance Corporation Strongsville, OH. Fuel Gas Treatment.
1 ChemE 260 Improvements and Non-Ideal Behavior in the Rankine Cycle May 20, 2005 Dr. William Baratuci Senior Lecturer Chemical Engineering Department.
Chapter 10 Vapor and Combined Power Cycles Study Guide in PowerPoint to accompany Thermodynamics: An Engineering Approach, 7th edition by Yunus.
Table of content 1- Heat exchanger design (cooler ) 2- Distillation column design. 3- Valve.
Super Critical Boilers Measures to improve Plant Efficiency And / or Heat Rate of Supercritical Units Turbine side measures : Higher steam parameters.
Heat Transfer Equations For “thin walled” tubes, A i = A o.
ENGR 2213 Thermodynamics F. C. Lai School of Aerospace and Mechanical Engineering University of Oklahoma.
Superheat Rankine Cycle Example Turbine pump condenser Q out Q in W out W in boiler Consider the superheat Rankine power cycle as we analyzed before.
Prepared by : Nishant .A. Raval
Dr. Owen Clarkin School of Mechanical & Manufacturing Engineering Summary of Energy Topics Chapter 1: Thermodynamics / Energy Introduction Chapter 2: Systems.
ME444 ENGINEERING PIPING SYSTEM DESIGN
PT.VENTURINDO ENGINEERING
Lesson 7 Steam Power Plant.
PT.VENTURINDO ENGINEERING
Water-tube Boilers Description of water tube boilers including operation, types and benefits. A brief synopsis on how they are applied to combined heat.
Vapor ,Gas and Combined Power Cycles
Objectives Evaluate the performance of gas power cycles for which the working fluid remains a gas throughout the entire cycle. Analyze vapor power.
Natural Gas Processing I Chapter 2 In-feed System
VARIABLE EFFECTING EFFICIENCY OF RANKINE,REHEAT,REGENERATIVE CYCLE
Thermodynamics Cycles.
Simple Thermal Power Plant
TOPIC:- VAPOUR CYCLES CREATED BY:
VAPOR & COMBINED POWER CYCLES
HEAT EXCHANGER.
UNIT IV- Vapour Power Cycles
Fulfilled the student of group ФЭ14-01B Zhuk Aleksey
Desuperheater Heat Transfer Device Manufactured by Maniks
Maniks high efficiency Desuperheater for efficient heat transfer
“Desuperheater” High Efficient Energy conservation Device for Refrigeration Use
PRODUCTS (POWER PLANT)
Furnace Heat Transfer & Steam Generation
Condensers.
Heat-transfer Equipment
Tracer Applications.
Steam traps Applications and Recommendations
Condenser in Power Plants
UNIT III PARTICULATE SCRUBBES. PARTICULATE SCRUBBERS or WET COLLECTORS Scrubbers are air pollution control devices that use liquid(often water) to remove.
Pneumatic System Conditioning
Presentation transcript:

V VENTURI SEPARATORS STEAM

INTRODUCTION PRODUCT DESCRIPTION ADVANTAGE The separators baffle combined type used for removal wet or liquid in the steam.condensate droplets during normal operation and within the steam flow at start up and cooling down. ADVANTAGE Prevent equipment damage due to erosion and corrosion Reduction in process efficiency due to lower heat transfer Reduce wet steam during saturated flow Prevent from water hammer defect Protect foreign material direct contact to equipment Thermal shock OPERATION The separators has two stage design, the first stage is baffle plate protected and coalesce by bringing foreign material and wet steam droplets together.the second stage wet steam force penetrated to the hole screen in order all the water droplets to the bottom.the condensate exits the separtor from a volute contoured drain. APPLICATIONS Steam turbine inlet to protect blade damage due to steam wet particle and pipe scales Boiler outlet, providing guarantied dry steam Exhaust steam lines Steam main line, prevent water hammer in pipe line

DIAGRAM HOW TO USE THE DIAGRAM 10 Bar steam pressure and 1000Kg/h flow from A-D and Extend A-B horizontally Any separator are intersecting with the A-B line in the blue are will be working efficiently 100% (DN50) Flow rate is determined by B-C vertical line (19 m/s) Pressure loss is established by intersecting A-B line to C-D line (0,03 Bar) Separators should be chosen by determining the flow rate line diameter and pressure loss

PT.VENTURINDO ENGINEERING SELECTION DATA INLET/OUTLET CLASS FLANGE PRESSURE TABLE (bar G) SATURATED TEMP (deg C) Up to SUPERHEAT TEST PRESSURE WEIGHT APPROX (Kg) SIZE Ø” & LENGTH BODY THICKNESS (mm) 4” PN25 20 212,4 280 30 309 16” x 1200L 13 PN40 233,9 320 45 19 ANSI 300 314 ANSI 600 40 250,4 425 60 6” 321 328 345 8” 337 341 350 356 10” 348 20” x 1200L 399 407 455 PT.VENTURINDO ENGINEERING Maintenance, Engineering & Contractor Head Office & Work Shop : Jl.By Pass jomin No.46 Cikampek, Karawang, West - Java Telp. 0264 8385523 Fax. 0264 8385523 Email : Didik.haryadi@venturindo.id engineering@venturindo.id