% The percent sign is computer language for: Get ready, here comes something you want or OK that is all you needed A “%” should be at the beginning and end of every program

(X,Y ZERO BOTTOM LEFT OF PART) (Z ZERO TOP OF PART) (CNC PROGRAMMING 1, #o1972) (J. DAILEY 2/14/05) (X,Y ZERO BOTTOM LEFT OF PART) (Z ZERO TOP OF PART) These lines are for the operator only. Everything in parenthesis cannot be seen by the CNC This intro can vary according to personal preference Notice all letters are upper case – some machine do not read lower case letters

N0010 G17 G20 G40 G80 G90 (Cancels anything you do not want and gets the machine ready for what you want to do)

N0020 T01 M06 (1/16 2FL BEM) (Calls up the tool you want and does the tool change)

N0030 G43 H1 Z1.0 (Calls up Tool Length Compensation and specifies which offset to use)

N0040 G41 D1 (Calls up Cutter Compensation left and specifies which offset to use)

N0050 M03 S3000 (Turns on Spindle (CW) and specifies the Spindle Speed)

N0060 M08 (Turns Flood Coolant On)

N0070 G54 G90 G00 X8.2500 Y3.7500 Z1.0000

N0080 G01 Z-.050 F6.0

N0090 G01 X7.5000 Y2.2500

N0100 G01 X6.0000 Y2.2500

N0110 G01 X6.0000 Y1.5000

N0120 G01 X3.0000 Y1.5000

The Gettysburg Address  Four score and seven years ago our fathers brought forth on this continent, a new nation, conceived in Liberty, and dedicated to the proposition that all men are created equal.  Now we are engaged in a great civil war, testing whether that nation, or any nation so conceived and so dedicated, can long endure. We are met on a great battlefield of that war. We have come to dedicate a portion of that field, as a final resting place for those who here gave their lives that that nation might live. It is altogether fitting and proper that we should do this.  But, in a larger sense, we cannot dedicate—we cannot consecrate—we cannot hallow—this ground. The brave men, living and dead, who struggled here, have consecrated it, far above our poor power to add or detract. The world will little note, nor long remember what we say here, but it can never forget what they did here. It is for us the living, rather, to be dedicated here to the unfinished work which they who fought here have thus far so nobly advanced. It is rather for us to be here dedicated to the great task remaining before us—that from these honored dead we take increased devotion to that cause for which they gave the last full measure of devotion—that we here highly resolve that these dead shall not have died in vain—that this nation, under God, shall have a new birth of freedom— and that government of the people, by the people, for the people, shall not perish from the earth.

The Gettysburg Address 268 words Less than 3 minutes to read Let your CNC programming be like President Abraham Lincoln’s writing Simple Accurate Straight to the point So lets start using “Modal” commands to our advantage……

N0130 Y2.2500

N0140 X.7500

N0150 X1.5000 Y3.7500

N0160 X3.0000

N0170 Y4.5000

N0180 X6.0000

N0190 Y3.7500

N0200 X8.2500

N0210 G00 Z1.0

N0220 M09 (Turn Coolant off)

N0230 M05 (Turn Spindle Off)

N0234 G40 (CANCELS CUTTER COMPENSATION)

N0236 G28 G91 Z0 (Rapid to Home Position)

N0240 G28 G91 X0 Y0 (Rapid to Home Position)

N0250 M30 (End of Program and rewind – could also be a “M02”

% (must be at beginning/end of program)