ISOMETRIC VIEW QUESTIONS 1

Slides:



Advertisements
Similar presentations
Fundamentals of Engineering
Advertisements

Perspective Sketching
Packaging Design: Net This net is for an octagonal based prism. As with all technical drawings, the equipment goes a long way in helping you to draw a.
SECTIONAL VIEWS.
Unit 5 Three-View Drawings
Design and drawing of RC Structures CV61
Orthographic Projection
Orthographic, Oblique & Isometric Projections
Interpret drawings of domestic structures. Drawing Layout The drawings on the next two pages show how a construction drawing can be laid out to show the.
Hexagons & Hexagonal Prisms. Hexagons Hexagons are 6 sided shapes. Hexagons can be dimensioned in 2 different ways. 1. Across the faces. 2. Across the.
DIEDRIC SYSTEM.
Aberdeen Grammar School Isometric Views. Isometric Drawings Lengths and breadths are drawn at 30° to the horizontal. Heights are drawn vertically. All.
Pyramid Construction Pyramids Square Rectangle Hex Cone.
CHAPTER 16 Engineering Drawings and Symbols
Technical Drawing Visual Communication of Technical Information
MECHANICAL DRAWING.
Introduction to Projections Four Basic Types
Orthographic Drawing.
AutoCAD 2D_I Module 3: Freehand Pictorial Sketching.
17/02/03Designed by Barry Forbes Graphic Communication Hexagons & Hexagonal Prisms.
Computer Aided Engineering and Design Prof. Dr. Demir Bayka.
IOT POLY ENGINEERING 2-16 January 26, 2010 Matching and Fill-in-the-Blank Identifying drawing types –Isometric, section, standard view, development, perspective,
Chapter 6 – Pictorial Sketching
J.Byrne Sofa Table Course work 12/13 J.Byrne
Sketching By Brian Nettleton This material is based upon work supported by the National Science Foundation under Grant No Any opinions, findings.
Hexagons & Hexagonal Prisms.
IOT POLY ENGINEERING 2-19 November 29, 2010 Your drawing space is 10” wide by 7 ¼” high. Calculate the horizontal starting point and the vertical starting.
60 Find the start point.. Draw a construction line horizontally across the page. 60.
Isometric Views.  Lengths and breadths are drawn at 30° to the horizontal.  Heights are drawn vertically.  All sizes are drawn to their exact sizes.
Plate No. 5. Make the Border line and Title Block – (5 Minutes ONLY) Divide the workspace and find the reference point – (5 Minutes ONLY) Draw the Isometric.
Everything we use has symbols and legends for us to follow. But we would never know what the symbols meant unless we had a Legend. Everything we use has.
Third angle orthographic projection
Hosted by Ms. Hamby Constraints Lines ViewsSketches
Draw the plan and the elevation of the cylinder, leaving 30mm between views Ø 40.
Reading Drawings.
PICTORIAL DRAWINGS.
Graphic Communication
Engineering Sketching (not in your book)
Tin Whisker Risk Model Spreadsheet
Following and Giving Instructions
CONSTRUCTION MASTERS BONUS BONUS
ORTHOGRAPHIC PROJECTION
ISOMETRIC PROJECTION RATHER DRAWING
Perspective Sketching
OBLIQUE VIEW 1 Down 205 In 50 Down 205 In 200
Starter Calculate the area of the following shapes 6m 120mm 110mm 4m
PDT176 COMPUTER-AIDED DRAFTING CHAPTER 5 ISOMETRIC DRAWING
ORTHOGRAPHIC PROJECTION 1
ENGN103 Engineering Drawing Isometric Projections
Isometric projections
SKETCHING.
Engineering Drawing ENGN103
ORTHOGRAPHIC PROJECTION
ISOMETRIC CIRCLES AND CYLINDERS
Lines used in drafting are lines whose appearance and meaning are determined by international agreements. Geometric Lines.
Computer Aided Design I
Isometric projections
ENGN103 Engineering Drawing Isometric Projections
DofE Gold Preparatory Map Skills
Pre-Engineering & Computer-Aided Design I
Isometric and Oblique Pictorials
MENG104 ENGINEERING GRAPHICS
Isometric and Orthographic Projections
Are the buildings below three dimensional shapes?
Graphic Communication
Projections & Technical Drawing
LOTTO LOGO Down 200 In 55 SHEET NO: 4.
Orthographic Projection:
Engineering Graphics I
Presentation transcript:

ISOMETRIC VIEW QUESTIONS 1 NAME: ST FINTINANS LONGWOOD DATE: 1 2 3 Down 125 In 70 Down 245 In 295 Down 245 In 70 4 5 6 Down 210 In 125 Down 210 In 320 Down 125 In 220 NOTE: 5 AND 6 ARE A DIFFERENT SHEET

ISOMETRIC VIEW QUESTIONS 2 NAME: ST FINTINANS LONGWOOD DATE: In 130 Up 20 In 140 Up 25 In 120 Up 15 In 120 Up 15 In 120 Up 15 In 180 Up 25

ISOMETRIC VIEW QUESTIONS 3 NAME: ST FINTINANS LONGWOOD DATE: In 170 Up 35 In 220 Up 40 In 233 Up 14 In 160 Up 50 In 295 Up 8

PREMIERSHIP CLUBS In 80 Up 18 In 118 Up 40 In 118 Up 40 NAME: ST FINTINANS LONGWOOD DATE: Thickness of each drawing is 7mm. Grids are made up of 7mm squares . 70 14 56 14 56 14 56 77 In 80 Up 18 280 56 14 56 14 56 77 In 118 Up 40 196 56 14 56 14 56 77 In 118 Up 40 196

ISOMETRIC VIEW 1 1 4 3 2 Down 125 In 70 Down 125 In 220 50 50 50 25 25 NAME: ST FINTINANS LONGWOOD DATE: 1 Down 125 In 70 4 Down 125 In 220 25 50 50 50 25 25 50 100 25 25 75 30° 30° 75 50 50 25 25 3 Down 245 In 70 Down 245 In 295 2 50 25 25 25 25 50 25 25 25 25 75 30° 50

ISOMETRIC VIEW 2 6 5 Down 210 In 125 Down 210 In 320 50 125 100 50 50 NAME: ST FINTINANS LONGWOOD DATE: 5 Down 210 In 125 Down 210 In 320 6 50 25 25 25 25 50 25 50 125 25 100 25 50 25 25 25 50 25

U 2 NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan of a logo for the U2 rock group are shown over. The grid is made up of 10mm squares. Draw an isometric view of the logo. Parallel lines on an object appear parallel in an isometric view. Draw the principal axes Mark off overall length, width and height of the logo along the appropriate axes. Complete the box into which the logo fits by drawing lines vertically and at 30 degrees in either direction. Mark off 10 mm intervals, along the axes and complete the grid as shown. Line in the letter U and the number 2 on the grid. Draw the depth lines as shown below. Complete the drawing as shown on the right. 110 180 In 130 Up 20 30° 15 30° SHEET NO: 60

TOY FISH NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan of a toy fish are show below. The fish is based on a gird which is made up of 20mm square. Draw an isometric view of the fish. 120 160 20 In 140 Up 25 30° 30° SHEET NO: 61

RALPH LAUREN NAME: ST FINTINANS LONGWOOD DATE: The letters RL are to be used to identify the Ralph Lauren section of a clothes shop. The elevation and plan of the letters are based on a 10mm grid are shown. Draw and isometric view of the letters. 120 200 In 120 Up 15 20 30° SHEET NO: 62

KEANO NO. 16 NAME: ST FINTINANS LONGWOOD DATE: The figure over shows the elevation and plan of a number for a jersey of the legendary Roy Keane. The grid is made up of 10mm squares Draw an isometric view of the letters. 140 180 In 120 Up 15 In 130 Up 10 15 30° SHEET NO: 63

PHARMACY NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan for a sign for a pharmacy are shown below. The grid is made up of 20mm squares. Draw an isometric view of the sign. 10 10 120 160 20 10 30° In 120 Up 15 10 SHEET NO: 64

GARDEN SHED NAME: ST FINTINANS LONGWOOD DATE: The elevation and end view of a garden shed are shown below. Draw an isometric view of the shed. The door is recessed 10mm, and the windows 5mm. 20 40 30 100 40 35 20 25 20 130 20 30 80 35 30° In 180 Up 25 25 SHEET NO: 65

FIRST AID BOX NAME: ST FINTINANS LONGWOOD DATE: 10 15 50 The elevation, plan and end view of a first aid box are shown below. The gird for the cross is made up of 10mm squares. Draw an isometric view of the box. 95 20 10 40 50 130 35 40 55 20 In 170 Up 35 SHEET NO: 66

“The ultimate toasting experience” TOASTER NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan of a toaster are shown, Draw an isometric view of the limited edition gold plated super toaster 3000. 15 Super toaster 3000 The ultimate toasting experience 15 Super toaster 3000 10 15 15 15 15 10 80 60 30 15 25 Super toaster 3000 “The ultimate toasting experience” Super toaster 3000 15 120 30° 70 15 In 220 Up 40 SHEET NO: 67

CASIO SUPER CALCULATOR 3000 NAME: ST FINTINANS LONGWOOD DATE: The figure shows the elevation and plan of a calculator. Draw an isometric view of the calculator. 10,000,000 1 35 10 4 2 25 20 7 5 3 10 15 + CASIO SUPER CALCULATOR 3000 8 6 10 15 - 9 10 10 10 15 15 = 10 10 15 15 10 160 10 20 10 80 30° In 160 Up 50 SHEET NO: 68

INK CARTRIDGE SUPER PRINTER 3000 In 233 Up 14 NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan of a box for an ink cartridge manufactured by Holden Limited are shown across. The front face of the box contains the company monogram, which is based on a 10mm square gird. Draw an isometric view of the box. 20 10 Instructions Take seal of cartridge and insert as show in instruction manual . Suitable for Super Printer 3000. 10 20 15 SUPER PRINTER 3000 10 15 150 110 20 80 120 In 233 Up 14 30° 20 40 SHEET NO: 69

DIY SIGN NAME: ST FINTINANS LONGWOOD DATE: The figure below shows the elevation and plan of a sign for the DIY department in a store. The grid for the letters is made up of 10mm squares. Draw an isometric view of the sign. 20 10 70 60 20 20 55 150 110 240 55 In 295 Up 8 70 30° 10 10 20 SHEET NO: 73

TEST SOLUTION Down 125 In 195 Elevation in the arrow A NAME: DATE: Down 125 In 195 Elevation in the arrow A Plan in the arrow C End View in the arrow B. Leave 20mm between views. Show hidden detail where necessary. Remember always draw the box that the object will fit in to. 80 15 15 20 30 70 120 20 70 30 20

M.U.F.C NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan for a monogram for Manchester United Football Club are shown Below. The gird is made up of 7mm squares. Draw an isometric view of the monogram. 56 14 56 14 280 56 77 14 70 In 80 Up 18 30°

CHELSEA F.C NAME: ST FINTINANS LONGWOOD DATE: “Chelsea don’t sack their managers, but if they did they'd probably be the best managers in the world” 56 14 56 77 196 14 56 In 118 Up 40 SHEET NO: 72

LIVERPOOL F.C NAME: ST FINTINANS LONGWOOD DATE: The elevation and plan for a monogram for Liverpool Football Club are shown Below. The gird is made up of 7mm squares. Draw an isometric view of the monogram. 56 14 56 77 196 14 56 30° In 118 Up 40 SHEET NO: 71