The Polarized SRF Gun Experiment Jörg Kewisch, September 26, 2007

Slides:



Advertisements
Similar presentations
Abstract PHOTOINJECTOR PRODUCTION OF A FLAT ELECTRON BEAM E. Thrane, Univ. of Michigan, C. Bohn, Northern Illinois University (NIU) and FNAL, N. Barov,
Advertisements

Ion Accelerator Complex for MEIC January 28, 2010.
JCS e + /e - Source Development and E166 J. C. Sheppard, SLAC June 15, 2005.
Polarized Electron PWT Photoinjectors David Yu, Marty Lundquist, Yan Luo, Alexei Smirnov DULY Research Inc. California, USA PESP 2008 at Jefferson Lab.
Design Concepts for Magnetic Insulation Diktys Stratakis Advanced Accelerator Group Brookhaven National Laboratory NFMCC Meeting – LBL January 28, 2009.
Generation and Characterization of Magnetized Bunched Electron Beam from DC Photogun for MEIC Cooler Laboratory Directed Research and Development (LDRD)
A Polarized Electron PWT Photoinjector David Yu DULY Research Inc. California, USA SPIN2004, Trieste, Italy 10/14/04.
Photocathode 1.5 (1, 3.5) cell superconducting RF gun with electric and magnetic RF focusing Transversal normalized rms emittance (no thermal emittance)
High Current Electron Source for Cooling Jefferson Lab Internal MEIC Accelerator Design Review January 17, 2014 Riad Suleiman.
E. Pozdeyev1 Ion Back-Bombardment in RF Guns Eduard Pozdeyev BNL with contributions from D. Kayran, V. Litvinenko, I. Ben-Zvi.
Study of Secondary Emission Enhanced Photoinjector Xiangyun Chang 1, Ilan Ben-Zvi 1,2, Andrew Burrill 1, Peter D. Johnson 2 Jörg Kewisch 1 Triveni S. Rao.
Electron Source Configuration Axel Brachmann - SLAC - Jan , KEK GDE meeting International Linear Collider at Stanford Linear Accelerator Center.
CLARA Gun Cavity Optimisation NVEC 05/06/2014 P. Goudket G. Burt, L. Cowie, J. McKenzie, B. Militsyn.
Accelerator Science and Technology Centre Extended ALICE Injector J.W. McKenzie, B.D. Muratori, Y.M. Saveliev STFC Daresbury Laboratory,
LDRD: Magnetized Source JLEIC Meeting November 20, 2015 Riad Suleiman and Matt Poelker.
RF source, volume and caesiated extraction simulations (e-dump)
R.Chehab/ R&D on positron sources for ILC/ Beijing, GENERATION AND TRANSPORT OF A POSITRON BEAM CREATED BY PHOTONS FROM COMPTON PROCESS R.CHEHAB.
F Cs 2 Te and NEA GaAs photocathode activities at Fermilab Raymond Fliller FNAL Workshop on High Quantum Efficiency Photocathodes for RF guns INFN Milano.
Electron Sources for ERLs – Requirements and First Ideas Andrew Burrill FLS 2012 “The workshop is intended to discuss technologies appropriate for a next.
A high-peak and high-average current, low emittance, long lifetime electron source* for ERL applications Xiangyun Chang June 9, 2015 Patent applied for.
July LEReC Review July 2014 Low Energy RHIC electron Cooling Jorg Kewisch, Dmitri Kayran Electron Beam Transport and System specifications.
FLS2010 Workshop, Stanford, March 1-5, 2010 Florian Loehl (Cornell University) Commissioning of the High Current ERL Injector at Cornell Florian Loehl.
MeRHIC Internal Cost Review October, Dmitry Kayran for injector group MeRHIC Internal Cost Review October 7-8, 2009 MeRHIC: Injection System Gun.
Development of High Current Bunched Magnetized Electron DC Photogun MEIC Collaboration Meeting Fall 2015 October 5 – 7, 2015 Riad Suleiman and Matt Poelker.
Progress of Bunched Beam Electron Cooling Demo L.J.Mao (IMP), H.Zhang (Jlab) On behalf of colleagues from Jlab, BINP and IMP.
Helical Accelerating Structure with Controllable Beam Emittance S.V. Kuzikov 1, A.A. Vikharev 1, J.L. Hirshfield 2,3 1 Institute of Applied Physics RAS,
11/12/20151 Status of high intensity polarized electron gun project at MIT-Bates Evgeni Tsentalovich MIT.
ELI PHOTOINJECTOR PARAMETERS: PRELIMINARY ANALYSIS AND SIMULATIONS C. RONSIVALLE.
An Electron source for PERLE
S.M. Polozov & Ko., NRNU MEPhI
Experiments on Fast Ion Instability at PLS
Beam dynamics simulation with 3D Field map for FCC RF gun
Positron production rate vs incident electron beam energy for a tungsten target
Preliminary result of FCC positron source simulation Pavel MARTYSHKIN
Development of X-band 50MW klystron in BVERI
Preliminary results for electron lens with beam current of 20 A
M. Migliorati, C. Vaccarezza INFN - LNF
by P. Musumeci and F.Tazzioli
DC Injector and Space Charge Simulation Status
Polarized Gun R&D at Fermilab
PANDA Collaboration Meeting
SRF Gun at ELBE Work package 10, Task 7 Jochen Teichert
Experimental Overview
Effects of External Fields on RF Cavity Operation
Magnetized Bunched Electron Beam from DC High Voltage Photogun
Parallel 3D Finite Element Particle-In-Cell Simulations with Pic3P*
The Cornell High Brightness Injector
ERL Main-Linac Cryomodule
Beam Dynamics in a Spilt SRF-Gun
June 9, 2015 Patent applied for.
Capture and Transmission of polarized positrons from a Compton Scheme
Magnetized Electron Beam for Ion Cooling at JLEIC
Electron Source Configuration
ATF 120 Hz Photocathode RF Gun Injection System Design Studies
Summary for the Sources working group
Injector: What is needed to improve the beam quality?
Pulsed Ion Linac for EIC
R. Suleiman and M. Poelker September 29, 2016
Superconducting High Brightness RF Photoinjector Design
Advanced Research Electron Accelerator Laboratory
Electron sources for FCC-ee
Physics Design on Injector I
June 9, 2015 Patent applied for.
LCLS Injector/Diagnostics David H. Dowell, SLAC April 24, 2002
PSB magnetic cycle 900 ms MeV to 2 GeV
Status of the JLEIC Injector Linac Design
小型X線源の性能確認実験計画 高輝度・RF電子銃研究会 広島大学 高エネルギー加速器研究機構 浦川順治
Update on ERL Cooler Design Studies
Ya. Derbenev JLEIC R&D meeting CASA Jefferson Laboratory
Generation of Magnetized Bunched Electron Beam for MEIC Cooler
Presentation transcript:

The Polarized SRF Gun Experiment Jörg Kewisch, September 26, 2007   Jőrg Kewisch, Ilan Ben-Zvi, Triveni Rao, Andrew Burrill, David Pate, Ranjan Grover, Rob Todd Brookhaven National Laboratory, Upton, NY 11973 and Hans Bluem, Doug Holmes, Tom Schultheiss Advanced Energy Systems, Medford, NY Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Abstract RF electron guns are capable of producing electron bunches with high brightness, which outperform DC electron guns and may even be able to provide electron beams for the ILC without the need for a damping ring. However, all successful existing guns for polarized electrons are DC guns because the environment inside is RF gun is hostile to the GaAs cathode material necessary for polarization. While the typical vacuum pressure in a DC gun is better than 10-11 torr the vacuum in an RF gun is in the order of 10-9 torr. Experiments at BINP show that this leads to strong ion back-bombardment and generation of dark currents, which destroy the GaAS cathode in a short time. The situation might be much more favorable in a (super-conducting) SRF gun. The cryogenic pumping of the gun cavity walls may make it possible to maintain a vacuum close to 10-12 torr, solving the problem of ion bombardment and dark currents. Of concern would be in this case contamination of the gun cavity by evaporating cathode material. This report describes an experiment that BNL (in collaboration with AES) is conducting to answer these questions. Parmela simulations show promising results. Jörg Kewisch, September 26, 2007

BINP experiment Aleksandrov, et al. Normal conducting gun Pressure 2*10-10 torr at before RF is turned on. Large dark current cause by ion bombardment of NEA surface Quantum efficiency life time a few seconds RF field of 30 MV/m does no irreversible damage 1 activation chamber, 2 photo-cathode assembly, 3 manipulator, 4 accelerating cavity, 5 wave guide, 6 focusing lens, 7 transverse corrector, 8 working chamber, 9 vacuum window for laser beam, 10 ceramic insulator, 11 the cavity for bunch length measurement. Jörg Kewisch, September 26, 2007

How Many Ions Impact Cathode in RF Gun? (Ray Fliller at Snowmass) MAGIC predicts 2.8x107 ions/C, generated from beam, impacting the cathode at a partial pressure of 10-10 torr. Dark current produced a bombarding ion flux of 1.6x107 ions/C at 10-10 torr. In contrast, a DC gun produces on the order of 3x107 ions/C striking the cathode at 10-11 torr . The RF gun seems to have an order of magnitude less in the number of ions impacting cathode at the same pressure. However RF guns typically run in 10-9 torr range. In addition, the maximum ion energy is ~2keV in the RF gun. Dark current generated ions generally have energies less than 500eV. Max ion energy in DC gun ~100keV Higher mass of ions means they quickly slip relative to the RF phase, as opposed to the continual acceleration in a DC gun. An RF gun should be able to support an GaAs cathode at pressures higher then a DC gun, but lower than current RF guns. Jörg Kewisch, September 26, 2007

Fermilab’s cold RF gun (Ray Fliller at Snowmass) Liquid N2 cooled Base pressure of uncooled, no RF, gun is 3x10-10 torr When RF applied to uncooled gun, most gases show increased outgassing. Pressure increases to 1.6x10-9. Cooling gun to 92K drops pressure by factor of 2. Applying RF to cooled gun increases pressure factor of 2, mostly due to methane out-gassing. Pressure slightly less than base pressure. Jörg Kewisch, September 26, 2007

“Getting cold” is not enough (R. Fliller at Snowmass) True cryopumping involves Gas molecules freezing to chamber walls A reduction in gas vapor pressure below total pressure Only CH4, C2H4, CO2 and H2O are frozen at 92K. Other gases merely collect in the cold volume, forming a lower pressure, higher density gas than exists in the warm section. Vapor pressures of the gases involved to not reach 10-10-10-11 torr until 20-30K. Cooling with Liquid He is necessary! Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Our Experiment Superconducting ½ cell 1.3 GHz gun Beam energy 0.8 MeV, current 10 A, limited by availbale RF power Removable NEA bulk GaAs cathode, 1 mm diameter. 100 liter cryostat, helium lasts about 24 hours Beam exits to on top, is bend 90 degrees into a Faraday cup Focusing with permanent magnet solenoids NEG pumps inside the cryostat, close to the gun, expected vacuum close to 10-12 torr. Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Cryostat Jörg Kewisch, September 26, 2007

Gun with cathode transporter Jörg Kewisch, September 26, 2007

Cathode connected to the preparation chamber Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Cathode transporter Jörg Kewisch, September 26, 2007

Clamping the cathode to the gun Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Cathode plug Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Tasks Gun base line testing at Jlab without hole Test cryostat Design plug and modification. Test GaAs attached to Nb (no gun) Modify and machine gun, clean at JLab or AES Base line testing with Nb plug, cold, low power RF, measure Q, impedance High power RF test with Nb plug Bates preparation chamber Our preparation chamber Low/high power RF test with Nb/GaAs plug, no Cs Transport system Low/high power RF test with Nb/GaAs/Cs plug Run experiment with Laser Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Magnetization We define the magnetization generated by the magnetic field on the cathode as: The angled brackets indicate the average over all electrons. According to Busch’s Theorem the magnetization is a constant of motion outside longitudinal fields when only axial symmetric fields are present. We also define the 4D emittance as the forth root of the determinate of the sigma matrix: with Jörg Kewisch, September 26, 2007

Round to Flat conversion The beam will then have an effective emittance of: After the round-to-flat converter the beam has the horizontal and vertical emittances of: and Given those equations we calculate the necessary 4D emittance and magnetization for an ILC injector: and Kwang-Je Kim: Round-to-flat transformation of angular-momentum-dominated beams. Phys. Rev.ST, 6, 104002 Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Proof of principle 700 MHz gun and linac M=10μ, ε4d=1μ Conversion at 20 MeV Energy spread 3.6*10-3 Space charge still importatnt Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Best so far Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Parameters Gun frequency: 350 MHz Linac Frequency 700 MHz (working on 350 MHz) Bunch length: ± 13.3 degrees Cathode radius: 6.3 mm Transverse temperature on the cathode: 0.03 eV (this corresponds to a cathode temperature of 80 deg K. The expected temperature in our experiment is about 3 deg K. Field on the cathode: 11.2 Gauss Magnetization 5 μ (not much increase expected for 8 μ) Energy at the exit of the gun: 5 MeV Further optimization possible (gun shape, frequency, linac) Jörg Kewisch, September 26, 2007

Including a Solenoid in the gun Jörg Kewisch, September 26, 2007

Jörg Kewisch, September 26, 2007 Conclusion Promising simulations indicate better than required 4D- emittance, leaving budget for the real world. Expectation that the experiment proves the feasability of GaAs SRF guns. Experiment progressing on a shoe-string budget Jörg Kewisch, September 26, 2007