Angles and Protractors IN102 - Unit5 Angles and Protractors

Introduction Network of springs, arms, struts, and shocks work together. Must be aligned correctly

Suspension System Principles Yaw is movement around z-axis. Pitch is movement around y-axis. Roll is movement along x-axis.

Wheel Alignment Fundamentals Camber is side-to-side vertical tilt of wheel. Lean away from center: positive camber Lean toward center: negative camber Zero camber: no tilt

Wheel Alignment Fundamentals Caster is forward or backward tilt of steering axis from vertical. Backward tilt: positive caster Forward tilt: negative caster

Wheel Alignment Fundamentals SAI is angle formed between steering axis and the vertical. Not adjustable Provides self-centering of front wheels Brings pivot point close to center

Wheel Alignment Fundamentals Included angle is the angle formed between SAI and camber line. Add SAI angle to camber angle. Diagnostic angle cannot be changed.

Wheel Alignment Fundamentals Scrub radius is distance between two imaginary points on road surface. Centerline of tire using camber line and point where SAI centerline contacts road

Wheel Alignment Fundamentals Scrub radius (cont’d) Zero scrub radius: Two lines intersect at center of tire at road surface. Positive scrub radius: Camber line is outside SAI line. Negative scrub radius: Camber line is inside SAI line.

Wheel Alignment Fundamentals Toe-in: Front wheels are closer together than rear wheels. Toe-out: Front wheels are farther apart than the rear wheels. Static toe is designed to compensate for slight wear in steering joints and components.

Wheel Alignment Fundamentals Toe-out on turns is toe setting of front wheel as vehicle turns. Correct positioning of wheels is obtained by Ackermann principle and layout.

Wheel Alignment Fundamentals Angle steering arms make with steering axis, projected toward center of rear axle.

Wheel Alignment Fundamentals Turning radius: how small a circle the vehicle can turn when steering wheel turned to limit

Wheel Alignment Fundamentals Thrust angle: relationship between centerline of vehicle and angle of rear tires

Wheel Alignment Fundamentals Setback: distance one wheel is set back from wheel on opposite side of axle Relative to imaginary lines through center of each wheel, perpendicular to centerline

Wheel Alignment Fundamentals Ride height is amount of distance between ground and specified part of vehicle. Technicians use computerized alignment machine to ensure all angles are correct.

Wheel Alignment Fundamentals Some technicians refer to proper alignment as five-wheel alignment. Steering wheel included Four common adjustments Shim Eccentric bolt Strut rod Ball joint adjusting sleeve

Maintenance and Repair Alignment always follows a specific order of adjustment. Start at rear. Rear caster Camber Toe Move to front. Caster

Maintenance and Repair Toe-out on turns: Referred to as TOOT, Ackerman angle, or track differential angle SAI: Angle formed by imaginary line running through upper and lower steering pivots relative to plumb line

Maintenance and Repair Rear thrust angle problems can result from accident or other impact that bends the rear axle or axle mounting points. Damage to cradle can force wheels out of alignment, changing caster, camber, toe, and creating pull and tire wear issues.

Summary Vehicle movement may be due to yaw, pitch, or roll. Wheel alignment is set using the vehicle’s control arms, knuckles, and frame.

Summary Factors affecting wheel alignment include camber, caster, steering axis inclination, toe-in and toe-out, scrub radius, toe-out on turns, turning radius, thrust angle, and ride height.

Summary Positive camber refers to the top of tires tilting away from the vehicle; negative camber refers to the top of tires tilting toward the vehicle; zero average camber refers to no tire tilt. Caster refers to the angle formed between the centerline of steering axis and true vertical, or the forward/backward tilt of the ball joints.

Summary Steering axis inclination (SAI) provides the front wheels with a self-centering function; it is formed by drawing a line through the upper and lower pivot points of the suspension assembly.

Summary Scrub radius (steering offset) is the distance between the center point of the tire contact patch at the road surface and the point of steering axis centerline contact with the road. The Ackermann principle ensures that the inner wheels turn at a sharper angle than the other wheels when turning.

Summary Thrust angle refers to the relationship of the rear wheels to the vehicle’s imaginary centerline. When performing a wheel alignment, be sure to check front and rear cradle, thrust angle, wheel setback, wheel camber, caster, toe, SAI, and toe-out on turns.

Summary There are three basic types of wheel alignment: two-wheel alignment, thrust angle, and four-wheel alignment.

Summary Wheel alignment servicing equipment is used to measure the steering and suspension alignment angles.

Credits Unless otherwise indicated, all photographs and illustrations are under copyright of Jones & Bartlett Learning.