Specify coordinate system on the Domain pane.

Slides:

Advertisements

Similar presentations

Writing Linear Equations Using Slope Intercept Form

Advertisements

Outline Overview of Pipe Flow CFD Process ANSYS Workbench

Position, Velocity and Acceleration

Perimeter and Area.

Simulation lasts 30 years Aquifer is 70% Quartz Specify domain’s starting fluid composition on the Initial pane Initial fluid in equilibrium with Quartz.

Lecture 15 Today Transformations between coordinate systems 1.Cartesian to cylindrical transformations 2.Cartesian to spherical transformations.

ENGR 215 ~ Dynamics Sections 16.4

Derivation of the Gaussian plume model Distribution of pollutant concentration c in the flow field (velocity vector u ≡ u x, u y, u z ) in PBL can be generally.

Homework Homework Assignment #13 Review Section 6.2 Page 389, Exercises: 25 – 33(EOO), 35 Rogawski Calculus Copyright © 2008 W. H. Freeman and Company.

Chapter 23 Electric Potential Electric potential energy(sec. 23.1) Electric potential (sec. 23.2) Calculating elec. potential(sec. 23.3) Equipotential.

Specify flow rate on the Domain pane. GWB will use Darcy’s law to calculate discharge from the viscosity, permeability, and driving force. You can set.

2-4: Writing Linear Equations Using Slope Intercept Form.

1 Imaging Techniques for Flow and Motion Measurement Lecture 7 Lichuan Gui University of Mississippi 2011 Correlation Interrogation & FFT Acceleration.

Chapter 10 Vector Calculus

Review of Vector Analysis

PTT 204/3 APPLIED FLUID MECHANICS SEM 2 (2012/2013)

Clean water Start and end times of two reaction intervals Specify domain’s starting fluid composition on the Initial pane.

1 He and hydrogenoid ions The one nucleus-electron system.

X1t models reactive transport in groundwater flows in one linear or radial coordinate. Set initial fluid composition and mass of sorbing mineral Fe(OH)

Specify domain’s starting fluid temperature on the Initial pane Porewater temperature is 40 °C.

Decouple reaction between carbonate and Benzene(aq), other forms of carbon. Config → Redox Couples… Default setting: all redox reactions are coupled.

HW# 2 /Tutorial # 2 WRF Chapter 16; WWWR Chapter 17 ID Chapter 3

Porewater temperature is 40°C Specify domain’s starting fluid temperature on the Initial pane.

Electricity and Magnetism

11/16/2015PHY 711 Fall Lecture 331 PHY 711 Classical Mechanics and Mathematical Methods 10-10:50 AM MWF Olin 103 Plan for Lecture 33: Effects of.

Variable inlet chemistry. Inlet fluid “contaminated” enters the domain from t = 0 to 2 years Inlet fluid “flush” enters the domain from t = 2 to 10 years.

3023 Rectilinear Motion AP Calculus. Position Defn: Rectilinear Motion: Movement of object in either direction along a coordinate line (x-axis, or y-axis)

Pulse of Benzene contaminated water is attenuated by biodegradation. X1t models reactive transport in groundwater flows in one linear, radial, or spherical.

5 ft 3ft 5ft 3ft Always write your answer with the unit of measurement.

7.4 Arc Length. I. Arc Length A.) Given the curve f (x), we can approximate the length from x = a to x = b by using the distance formula.

Week 9 Presentation 1 Electromagnets 1. Learning Objectives: 1. Determine the magnitude and direction of the magnetic field strength generated by a straight.

Presentation File: Additional materials 12Aug20111CMDAYS 2011 Aravamudhan Download Presentation.

Clean water Specify starting fluid composition on the Initial pane.

Chapter 23 Electric Potential & Electric Potential Energy.

Lecture VI The description of the Plane Curvilinear Motion by the Polar Coordinates Polar coordinates.

Circles in the Coordinate Plane

Chapter 23: Electric Fields

2D Jet Simulation Testing

From: The Sedov Blast Wave as a Radial Piston Verification Test

16.2 Arc Length and Radian Measure

MHD planet simulations

Starter: Determine the direction of the missing vector.

You control discretization on the Domain pane.

A charge distribution lies along a segment of the positive x axis

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

Rate of Change and Accumulation Review

I see three “parts” to the wire.

The Initial fluid has negligible Pb2+ everywhere but the central node

פחת ורווח הון סוגיות מיוחדות תהילה ששון עו"ד (רו"ח) ספטמבר 2015

Specify domain’s starting fluid composition on the Initial pane

Calculate Area with grid lines no grid lines. Calculate Area with grid lines no grid lines.

EXAMPLE 2 Find lengths in circles in a coordinate plane

Prof. dr. A. Achterberg, Astronomical Dept

Kinematics of Particles

AE/ME 339 Computational Fluid Dynamics (CFD) K. M. Isaac

PHY 711 Classical Mechanics and Mathematical Methods

Gravitational Fields Pg

Packet #7 Applications: Rates of Change

Calculate Area with grid lines no grid lines. Calculate Area with grid lines no grid lines.

Section 2 –Linear and Angular Velocity

2-4: Writing Linear Equations Using Slope Intercept Form

The equations for circular motion are identical to those of linear motion except for variable names. True False.

12.6: Vector Magnitude & Distance

PHY 711 Classical Mechanics and Mathematical Methods

Circles in the Coordinate Plane

Specifying Boundary Conditions

PHY 711 Classical Mechanics and Mathematical Methods

Stream function in polar coordinate

Presentation File: Additional materials

Presentation transcript:

Specify coordinate system on the Domain pane. You can set up a model in linear, radial, or spherical coordinates in X1t. Specify coordinate system on the Domain pane. Set the number of nodes, Nx. Set either domain length, x, or grid spacing, ∆x.

You can set up a model in linear, radial, or spherical coordinates in X1t. Set the number of nodes, Nx. Set small-end radius, r1 Set either large-end radius, r2, or grid spacing, ∆r.

You can set up a model in linear, radial, or spherical coordinates in X1t. Set the number of nodes, Nx. Set small-end radius, r1 Set either large-end radius, r2, or grid spacing, ∆r.

Set the number of nodes along y, Ny. Set either domain width, y, or grid spacing, ∆y. You can set up a model in rectilinear or axisymmetric coordinates in X2t. Set the number of nodes along x, Nx. Set either domain length, x, or grid spacing, ∆x.

You can set up a model in rectilinear or axisymmetric coordinates in X2t. Set the number of nodes along y, Ny. Set either domain width, y, or grid spacing, ∆y. Set the number of nodes, Nx. Set small-end radius, r1 Set either large-end radius, r2, or grid spacing, ∆r.

X1t and X2t will account for the domain’s coordinate system in calculating the flow field. In an axisymmetric domain, fluid velocity decreases with distance from the wellbore. Small-radius end. Large-radius end.