SNS COLLEGE OF ENGINEERING, COIMBATORE

Slides:



Advertisements
Similar presentations
Chuck Gallant Baris Akcora Andy Grueninger. Introduction to Waterjet Fastest growing machining process One of the most versatile machining processes Compliments.
Advertisements

Machine Tools And Devices For Special Technologies Electrochemical machining Slovak University of Technology Faculty of Material Science and Technology.
ME 330 Manufacturing Processes CUTTING PROCESSES
LASER CUTTING ISE. WHAT IS A LASER CUTTER? ● Laser stands for Light Amplification by the Stimulated Emission of Radiation ● The laser is a monochromatic.
Abrasive Jet Machining (AJM)
NONTRADITIONAL MACHINING AND THERMAL CUTTING PROCESSES
MFET  1. Basic Principles  2. Hardware  3. Abrasives  4. Parameters  5. Capabilities  6. Advantages  7. Disadvantages.
Electron Beam Machining Ultrasonic Machining Abrasive Water Jet Machining PRESENTATION Submitted to: Mr Deepak Sharma Submitted by: Mayank Gupta ME-1 3.
There are two types of waterjet cutting
Mechanical Methods of Material Removal
Nathan Halladay & Daniel Zalit December 07,2001. Outline Process Description Design Considerations Advantages Disadvantages Web Info Questions.
Chapter 7IT 2081 Thermal and Other Methods of Material Removal Chapter 7.
Non-traditional Machining Processes
Machining is processes in which we get a desired final shape and size from of raw material. 1.Conventional / Traditional Machining 2.Non Conventional.
FINISHING OF COMPOSITES. APPROACH TO FINISHING COMPOSITES Composite materials can be trimmed and cut more easily with processes closer to grinding or.
پروژه درس روش های تولید استاد : دکتر خوش کیش تهیه کننده: مرتضی عسگری
PRESENTED BY ALBERT.N Under the guidance of Mr.N.RAMANUJAM M.E (Ph.d) (Associate Prof/Hod- Mech) DEPARTMENT OF MECHANICAL ENGINEERING E.G.S.PILLAY ENGINEERING.
Parameters Analysis for Low Power Q-Switched Laser Cutting in Singulation Process of HDD Manufacturing The 4th AIT Masters Theses Competition Present By.
Abrasive Water Jet Machining (AWJM)
Laser Beam Machining Done By: Murad.
ABRASIVE JET MACHINE.
 It is the material removal process where the material is removed by high velocity stream of air/gas or water and abrasive mixture.  An abrasive is.
Manufacturing processes
Processes Used to Separate Metallic Materials
Airbrasive Jet Machining
1 Water Jet Machining. 2  Key element in WJM – a jet of water.  Water jet travels at velocities as high as 900 m/s (approximately Mach 3).  When the.
Developed By Jared Storrs Masters Project Engineering Technology and Education Dept. Utah State University Materials and Processes Intro to Manufacturing.
SEMINAR ON HIGH SPEED MACHINING (HSM). CONTENTS  Introduction  Definition of HSM  Advantages  Application areas  Machining system  Some recommended.
Electrochemical Machining (ECM)
Non-traditional Machining Processes Manufacturing processes can be broadly divided into two groups: a)primary manufacturing processes : Provide basic shape.
PRESENTATION on EDM, ECM& LBM Presented by-: kumar saurabh Roll no-: Branch-: ME 1 Submitted to-: Mr Deepak Sharma.
Abrasive Jet Machining ( AJM ) Fig : Schematic illustration of Abrasive Jet Machining 1. AJM is a metal removal by mechanical erosion caused by the use.
ENM208 INTRODUCTION to MACHINING ANADOLU UNİVERSITY Industrial Engineering Department.
C.U. Shah College of Engg. & Tech
Lecture # 7 THEORY OF METAL MACHINING 1.Overview of Machining Technology 2.Theory of Chip Formation in Metal Machining 3.Force Relationships and the Merchant.
1 Electrochemical Machining (ECM). 2 Electrochemical Machining Uses an electrolyte and electrical current to ionize and remove metal atoms Can machine.
Team members: Mohamad Faisal b. Mohamad Khairi Harith Fahmi b. Mazlan Mohd Amirul Asraf b. Abu Bakar Mohd Asraf b. Arbain Asraf b. Arsyad Mohd Hafiz b.
MCQ. 1. the process of converting of row material in to finished product using machine is called as __________ a. Finishing process b. Metal cutting process.
DESIGN AND DEVELOPMENT OF GRINDING ATTACHMENT ON LATHE MACHINE
Laser cutting system.
ELECTRICAL ENERGY BASED PROCESSES
ULTRASONIC MACHINING PROCESS Prepared by B.BALAMURALI AP/MECH
Non-traditional Machining Processes
SNS COLLEGE OF ENGINEERING, COIMBATORE
ANADOLU ÜNİVERSİTESİ Industrial Engineerng Department
WATER JET MACHINING Prepared by B.BALAMURALI AP/MECH
Abrasive Water jet Machining
S.T.B.S. COLLEGE OF DIPLOMA ENGG,SURAT
Basic Machine Processes
Chemical and Electro-Chemical Energy Based Processes
Cutting Speed, Feed, and Depth of Cut
ELECTRICAL ENERGY BASED PROCESSES
WATER JET MACHINING.
ABRASIVE JET MACHINING Prepared by B.BALAMURALI AP/MECH
PRESENTATION ON ABRASIVE WATER JET MACHINING
Manufacturing Rounded Shapes II
PLASTIC FORMING PROCRSSES
Automated abrasive water jet pin cutting system – mark II
Practical Metalworking
Visit for more Learning Resources
UNCONVENTIONAL MACHINING PROCESSES
Basic Machine Processes
WEEK 8 Water Jet Machining & Abrasive Water Jet Machining
Files Module 5.
Associate Prof. Mohamed Ahmed Awad
Basic Machine Processes
Waterjet & Abrasive Waterjet
Unconventional Machining
Prepared by: Shayfull Zamree Abd Rahim
1 Cutting Speed, Feed, and Depth of Cut Compiled for CAT-II Trainees C.D.M BARC TROMBAY.
Presentation transcript:

SNS COLLEGE OF ENGINEERING, COIMBATORE- 641 107 SNS COLLEGE OF ENGINEERING, COIMBATORE- 641 107.   DEPARTMENT OF MECHANICAL ENGINEERING   ABRASIVE WATER JET MACHINING & PROCESS PARAMETERS OF AWJM Prepared by B.BALAMURALI AP/MECH ME 6004- UMP / TOPIC-10&11 SNSCEME PRESENTATION

Draw the AJM & WJM working diagram. RECAP Draw the AJM & WJM working diagram. ME 6004- UMP / TOPIC-10&11 SNSCEME PRESENTATION

Abrasive Water Jet Machining AWJM – entrained – three phase – abrasive, water and air. AWJM – suspended – two phase –abrasive and water o Direct pumping o Indirect pumping o Bypass pumping ME 6004- UMP / TOPIC-10&11

Abrasive Water Jet Machining ME 6004- UMP / TOPIC-10&11

General Experimental conditions Orifice – Sapphires – 0.1 to 0.3 mm Focusing Tube – WC – 0.8 to 2.4 mm Pressure – 2500 to 4000 bar Abrasive – garnet and olivine - #125 to #60 Abrasive flow - 0.1 to 1.0 Kg/min Stand off distance – 1 to 2 mm Machine Impact Angle – 60o to 900 Traverse Speed – 100 mm/min to 5 m/min Depth of Cut – 1 mm to 250 mm ME 6004- UMP / TOPIC-10&11

Components of AWJM ME 6004- UMP / TOPIC-10&11

Components of AWJM ME 6004- UMP / TOPIC-10&11

Components of AWJM Catcher (a) water basin (c) catcher plates (TiB2) (b) steel/WC/ceramic balls ME 6004- UMP / TOPIC-10&11

Advantages of AWJM • Extremely fast set-up and programming • Very little fixturing for most parts • Machine virtually any 2D shape on any material • Very low side forces during the machining • Almost no heat generated on the part • Machine thick plates ME 6004- UMP / TOPIC-10&11

ACTIVITY!!! DUBBING…………….. ME 6004- UMP / TOPIC-10&11

Setup ME 6004- UMP / TOPIC-10&11

When is it Practical? The cutter is commonly connected to a high-pressure water pump, where the water is then ejected from the nozzle, cutting through the material by spraying it with the jet of high-speed water. It’s practical to use it to cut any kind of material. In waterjet cutting, there is no heat generated. This is especially useful for cutting tool steel and other metals where excessive heat may change the properties of the material. Waterjet cutting does not leave a burr or a rough edge, and eliminates other machining operations such as finish sanding and grinding. It can be easily automated for production use. ME 6004- UMP / TOPIC-10&11

APPLICATION It can be used to cut intricate contours. This process is convenient for cutting relatively soft and non-metallic materials like paper boards, plastic, wood, rubber, leather, fibre glass, etc., ME 6004- UMP / TOPIC-10&11

Advantages Cheaper than other processes. Cut virtually any material. (pre hardened steel, mild steel, copper, brass, aluminum; brittle materials like glass, ceramic, quartz, stone) Cut thin stuff, or thick stuff. Make all sorts of shapes with only one tool. No heat generated. Leaves a satin smooth finish, thus reducing secondary operations. Clean cutting process without gasses or oils. Modern systems are now very easy to learn. Are very safe. Machine stacks of thin parts all at once. This part is shaped with waterjet using one tool. Slots, radii, holes, and profile in one 2 minute setup. ME 6004- UMP / TOPIC-10&11

Advantages (continued) Unlike machining or grinding, waterjet cutting does not produce any dust or particles that are harmful if inhaled. The kerf width in waterjet cutting is very small, and very little material is wasted. Waterjet cutting can be easily used to produce prototype parts very efficiently. An operator can program the dimensions of the part into the control station, and the waterjet will cut the part out exactly as programmed. This is much faster and cheaper than drawing detailed prints of a part and then having a machinist cut the part out. Waterjets are much lighter than equivalent laser cutters, and when mounted on an automated robot. This reduces the problems of accelerating and decelerating the robot head, as well as taking less energy. Get nice edge quality from different materials. ME 6004- UMP / TOPIC-10&11

Disadvantages One of the main disadvantages of waterjet cutting is that a limited number of materials can be cut economically. While it is possible to cut tool steels, and other hard materials, the cutting rate has to be greatly reduced, and the time to cut a part can be very long. Because of this, waterjet cutting can be very costly and outweigh the advantages. Another disadvantage is that very thick parts can not be cut with waterjet cutting and still hold dimensional accuracy. If the part is too thick, the jet may dissipate some, and cause it to cut on a diagonal, or to have a wider cut at the bottom of the part than the top. It can also cause a rough wave pattern on the cut surface. Waterjet lag ME 6004- UMP / TOPIC-10&11

Disadvantages (continued) Taper is also a problem with waterjet cutting in very thick materials. Taper is when the jet exits the part at a different angle than it enters the part, and can cause dimensional inaccuracy. Decreasing the speed of the head may reduce this, although it can still be a problem. Stream lag caused inside corner damage to this 1-in.-thick stainless steel part. The exit point of the stream lags behind the entrance point, causing irregularities on the inside corners of the part. The thicker the material is or the faster an operator tries to cut it, the greater the stream lag and the more pronounced the damage. ME 6004- UMP / TOPIC-10&11

After waterjet cutting Waterjets vs. Lasers Abrasive waterjets can machine many materials that lasers cannot. (Reflective materials in particular, such as Aluminum and Copper. Uniformity of material is not very important to a waterjet. Waterjets do not heat your part.  Thus there is no thermal distortion or hardening of the material. Precision abrasive jet machines can obtain about the same or higher tolerances than lasers (especially as thickness increases). Waterjets are safer. Maintenance on the abrasive jet nozzle is simpler than that of a laser, though probably just as frequent. After laser cutting After waterjet cutting ME 6004- UMP / TOPIC-10&11

Waterjets are much faster than EDM. Waterjets vs. EDM Waterjets are much faster than EDM. Waterjets machine a wider variety of materials (virtually any material). Uniformity of material is not very important to a waterjet. Waterjets make their own pierce holes. Waterjets are capable of ignoring material aberrations that would cause wire EDM to lose flushing. Waterjets do not heat the surface of what they machine. Waterjets require less setup. Many EDM shops are also buying waterjets.  Waterjets can be considered to be like super-fast EDM machines with less precision. Waterjets are much faster than EDM. ME 6004- UMP / TOPIC-10&11

ME 6004- UMP / TOPIC-10&11

ME 6004- UMP / TOPIC-10&11