Welding Trades Oxy Fuel Welding.

Slides:



Advertisements
Similar presentations
Objective Examine Oxy-fuel procedures.
Advertisements

OXYGEN-ALTERNATE FUEL TORCH EASY SET UP June 4, 2011 Chad Koens District Manager
Oxyfuel Welding and Cutting Equipment, Setup, and Operation
USING THE OXYACETYLENE CUTTING TORCH
Ag Metals I Using Gas Welding Equipment. Objectives Identify major part of oxyacteylene welding equipment Change oxygen and acetylene cylinders Turn on.
UNIT: Oxy-Fuel Welding, Brazing, Cutting and Heating LESSON: OXY-ACETYLENE EQUIPMENT SAFETY Standard B7.2 – Know how to properly set up, adjust, shut down.
Oxy – Fuel Torch Ag Mechanics.
Oxyacetylene Torches.
Oxyfuel Gas Welding & Cutting
OxyFuel Equipment Section 7
Oxygen/ Fuel Cutting and Welding By Ryan Saucier.
Using the Oxy-Acetylene Cutting Torch Alisa Colli AgEd 410 Fall 1999.
Oxy Fuel Cutting Systems Basic Setup & Use
Gas Heating, Cutting, Brazing, and Welding
UNIT: Oxy-Acetylene Welding, Brazing, Cutting and Heating
HOW TO LIGHT AND TURN OFF THE OXY-ACETYLENE TORCH
OXY-ACETYLENE TORCHES Protect your head and eyes by wearing proper welding goggles or face shields equipped with a minimum shade 5 lens. Protect your.
Oxyfuel Fusion Welding
Proper Procedures for Oxyacetylene Processes
Oxyacetylene Cutting.  After completing this chapter, you will be able to: ◦ Demonstrate the proper and safe method of setting up cylinders, regulators,
OXYFUEL WELDING. INTRODUCTION Oxyfuel welding is a welding process where the heat for fusion is supplied by a torch using oxygen and a fuel gas. Several.
Oxy-fuel Welding and Cutting By: John Templeton
Oxyacetylene Welding (OAW)
SAFETY AND PROCEEDURES
Agricultural Science II.  Define the chapter terms on an exam with 90% accuracy.  Describe the proper/safe way to turn the oxyacetylene rig on and off.
Oxyfuel Welding Equipment
Andrew Brock. Terms  The burning qualities of gases are used in Ag Mechanics to heat, weld and cut metals  Weld- to join by fusion  Fusion- melting.
Welding and Cutting Safety Safety Unit Lesson 5. Oxy-Fuel Welding & Cutting Oxy-fuel welding and cutting are the most common causes of fires in the welding.
Terms and Definitions Base Metal: Metal to be welded Fusion Welding: process that joins metals by heating them to a melting point and allowing them to.
Welding Power Point Halton Auto Mike Tew. Oxygen Regulator Pressure 20PSI- 35PSI Tall Green Tanks Power behind the flame High Pressure Tank volume 2500PSI.
Theory Review Oxy Fuel and SMAW. Oxy/Fuel 1.What gas provides the hottest flame when burned with oxygen? a. Natural gas b. Propane c. Acetylene d. MAPP.
Oxy Fuel Welding Basic Setup & Use
Oxy/fuel gas welding and cutting equipment.
Gas Welding.
Oxygen Acetylene Equipment Oxygen = Green Acetylene = Red.
Welding and Oxy – Acetylene Cutting
Oxyacetylene Cutting O.A.C. Pattern Cutter Cutting Torch.
Oxy Acetylene Welding and Cutting
New Mexico FFA Agricultural Mechanics Career Development Event
Welding and Cutting Safety
Welding Tool ID. What to do!  In order to receive all points that you missed, you must have the correct tool next to the name and what it is used for.
5 th and 8 th Mr. Luper.  Keep the cylinders upright at all times  In storage  On carts  Keep cylinders secured  Mark cylinders when empty  Write.
Oxy-Fuel Welding. What is Oxy-Fuel Welding? Process the fuses metal together Does not require electricity Uses a torch and filler rod Similar equipment.
Oxyacetylene Start Up/Shut Down Procedure Prepared by Dr. Dale Carpentier and Mr. Barry Brazelton Monroe Area High School Modified by Georgia Agriculture.
The Welding/Cutting Torch Objective 25.0 Demonstrate proper procedures for oxyacetylene processes.
Oxy Fuel Systems Basic Setup & Use Mr. Lacey Livingston High school.
Oxyacetylene Fusion Welding Safety Review
Teknologi Dan Rekayasa
GAS WELDING.
Using Gas Welding Equipment
Welding Safety Test Review
Proper Procedures for Oxyacetylene Processes
Oxyacetylene Welding Processes
Oxy-Acetylene Torches
Copyright © Texas Education Agency, All rights reserved.
Unit 22 Ag mechanics Using gas equipment.
Teknologi Dan Rekayasa
Oxyacetylene Start Up/Shut Down Procedure
Chapter 8 – Cutting Processes
Introduction to Agricultural Science and Technology
Compressed Cylinder Safety
Cutting Tip Chart 7. Refer to a cutting tip selection chart for correct cutting tip, regulator pressures, and travel speed.
Welding and Oxy – Acetylene Cutting
THE OXYACETYLENE TORCH
Shutting Down the Cutting Outfit
Linnert, Welding Metallurgy,
Oxygen/ Fuel Cutting and Welding
Gas Welding: Oxyacetylene By: Meghan Beckendorf AGRI 2222.
Welding and Oxy – Acetylene Cutting
Oxygen Acetylene Cutting Torch
Presentation transcript:

Welding Trades Oxy Fuel Welding

Objectives Objectives Objectives Explain oxyfuel cutting safety. Identify and explain oxyfuel cutting equipment & flames Identify and explain backfire and flashbacks Set up & shut down oxyfuel equipment Light and adjust an oxyfuel torch. Change empty cylinders Perform oxyfuel cutting – straight line

Safety First Review the safety sheet

Material You Need Oxygen Gas and Cylinders Acetylene and Cylinders Regulators Hoses Torches Cutting Tips

Work Activities Lab 1 Turning off the oxy fuel rig Lab 2 Turning on the oxy fuel rig

Clean Up & Review Check and Re-Check Your Work Review Terminology Keep Safety in Mind Take Test

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.