© The Author(s) Published by Science and Education Publishing.

Slides:

Advertisements

Similar presentations

University of Cambridge Department of Materials Science and Metallurgy

Advertisements

RG1 University of Chemical Technology and Metallurgy Department of Materials Science Microstructure and Mechanical Properties of Austempered Ductile Cast.

and Statistics, 2016, Vol. 4, No. 1, 1-8. doi: /ajams-4-1-1

Percentage of Polyethylene

Properties Test results

© The Author(s) Published by Science and Education Publishing.

Supplier Input Process Output Customer

Percentage composition (%)

Table 2. Result of Actual Technical Writing Needs

. EFFECT OF CARBON NODULES ON CONTACT ANGLE OF AUSTEMPERED DUCTILE IRON (ADI) Sonu Praneeth Gandam, Sourav Das, Dr. Pradeep Rohatgi Department of Material.

Research, 2015, Vol. 3, No. 6, doi: /education

Table 5. Properties of The Tested Soil

Tensile strength (MPa) Length (m) of fibers/kg

Tensile Strength (MPa)

No. of runs Xo X1 X2 X3 X4 Y1 Y2 Y3 Y4 Y5 Si

© The Author(s) Published by Science and Education Publishing.

Materials Science MENG 286

Tensile Test after Firing

Table 3. Descriptive Statistics – All Banks

Teachers Response (N= 11)

© The Author(s) Published by Science and Education Publishing.

Reservoir Capacity (m3)

Table 1. The radial spheroidal functions

Year range Rainfall (mm) ∆s in rainfall Temp (°C) ∆s in temp RH (mm)

Total CO2 Emissions (Electricity + Fossil Fuel)

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Contrast equality of group means

Number of categories that are mentioned (0% < categories < 5%)

Table 1. Geometric properties of steel tubes used

Table 2. Modal parameters estimated by Pulse Reflex®

© The Author(s) Published by Science and Education Publishing.

No. Of units of single building Rated power (W) of unit load

Table 5. Pvalues of ttests for direction a

Transformer Annual MVA Loadings (%) Average MVA Loading (%)

Interpass temperature

Table 2. Air-water flow cases

Text Format Files Number Files Size(Bytes) Words Number

Table 1. Population by University

Table 3. Main properties of the thin brass electrode

Table 5. Maximum stress, strain and deformation values

Table 1. Characterization Result of Leaded Petrol and Blends

Simulation Frequency(Hz)

Injection Substations No. of Transformer Units Installed

© The Author(s) Published by Science and Education Publishing.

Table 6. Pvalues of ttests for direction b

Table 1. Descriptive Statistics

Table 2. Regression statistics for direction a

Table 3. Regression statistics for direction b

Average Hardness value (HRC)

Control Valve Tag Number

Table 2. SUMMARIZED OBSERVATIONS FROM MODEL ANALYSIS

Table 4. Surface roughness (outer faces)

Electrode ν (mm/s) I (A) V (V) HI (J/mm) HI average AWS E309L

Table 2. Control Valves & Bypass Valves Process Data

95% Confidence Interval for Mean

© The Author(s) Published by Science and Education Publishing.

Control Valve Tag Number

Accomplished Recommendation Planned Actions for Control

Table 1. K-T Diagram for Bicycle Seat

No. of runs Xo X1 X2 X3 X4 Y1 Y2 Y3 Y4 Y5 Si2

Table 4. Value creation (Y2)

Table 3. Surface roughness (inner faces)

Table 7. The Result of T Test After Treatment

Flow rate of fuel (kmol/h) = 120

Compressive Strength difference at 1 week (MPa)

Table 6. Twisting moment of counter shaft at different torques

© The Author(s) Published by Science and Education Publishing.

Average Execution Time in seconds

Presentation transcript:

© The Author(s) 2015. Published by Science and Education Publishing. Table 4. Cost analysis of the activities during the quenching of the steel No Activity Activity Description Cost (N) 1 A Material Identification/purchase 8,000 2 B Cutting of material purchased 2,000 3 C Machining of the material to specific dimension 10,000 4 D Preparatory process/preparing the materials needed for the heat treatment - 5 E Quenching of the steel 25,500 6 F Polishing of the quenched steel for microstructural investigation 3,200 7 G Mechanical testing process O. C. Okwonna et al. Microstrucural Investigation and Network Analysis for Austempering Process Using a Blend of Palm Kernel Oil and Bitumen on High Carbon Steel and Ductile Iron. Materials Science and Metallurgy Engineering, 2017, Vol. 4, No. 1, 29-33. doi:10.12691/msme-4-1-3 © The Author(s) 2015. Published by Science and Education Publishing.