1. MAIN A. Main Controller Unit A-2. Group Mode A-3. Conference Mode ⑧ ⑨ 1. MAIN ⑤ ⑥ ⑩ ⑪ ⑦ SET DOWN UP CONFIRM ⑫ ⑬ ⑭ ⑮ A. Main Controller Unit A-2. Group Mode Start-up setting is “15 Group” and the one of the 100 preset levels(00~99) are displayed and operated. The Group must be agreed for the proper use. (The data is remained whether the system is off) Level DOWN Level UP SET Level / Mode Confirm ANT socket Voting Input Camera Input OUTPUT INPUT Fuse AC IN jack POWER switch (ON/OFF) LCD Display Mode SET switch Headphone input A-3. Conference Mode Start-up setting is “OPEN” and speaking requests can be displayed and flashed on MIC Stand LED& Microphone LED. (Max 3~4 Microphones can be simultaneously active.) After the speaking, Microphone stand will be TALK ON mode automatically in standby order. If the first speaker’s microphone stand is OFF, the last speaker’s one will be automatically ON under Override Mode (except the Chairman unit). The Controller and Chairman unit are exempted from this function. (The data is remained whether the system is off.) ▶ Press SET(3) for about 2 seconds to activate the Setup Mode. Pressing SET(3) button again can go to the next process under Setup Mode. To finish the Setup Mode, please press SET(3) button for about 2 seconds. ▶Use DOWN(1) or UP(2) to select the level and press CONFIRM(4) button to save and store the data in the memory. A-4. Priority Mode Start-up setting is “OFF”. The Priority OFF enables Chairman Unit to change the TALK ON Mode to OFF Mode each delegate’s microphones. Priority Mute function can stop speaking during TALK ON Mode and the status will be displayed and flashed on TALK LED & Microphone LED. Chairman Unit can cancel the Priority Mute order on delegate microphone. The Controller and Chairman unit are exempted from Priority OFF & Priority Mute functions. A-1. Procedure of Setup Mode Headphone Level → Aux Input ON, OFF → Aux Input Level → Speaker ON / OFF→ Speaking Time → Conference Mode → Priority Mode → Group Mode

② ④ ① ⑤ ⑥ ⑦ ③ ⑧ ⑨ ⑩ B. Chairman/Delegate unit Initial Fig Normal Fig Stand Setting Fig Microphone Input Microphone ON/ OFF button Inner Speaker Voting button (Agreement ) Voting button (Neutrality) Voting ( Opposition ) & SET button Level DOWN Level UP SET ② ④ ① ⑤ ⑥ ⑦ ③ ⑧ ⑨ ⑩ (MODE) Initial Fig Normal Fig ※ PRIO switch is a substitute for MODE switch to the Delegate Unit. B-1. POWER ON/OFF ▶ Press ⑩ button for about 3 seconds and Stand will be ON. Product’s distinct address will be showed up on initial page. Pressing ③button can show elapsed time on the Stand Setting Fig①. Press ON/OFF button③ for about 5 seconds, Stand will be OFF. B-4. Address Setting 1) Chairman Unit According to the procedure, ‘ADD’ will flash to display the status. Select the Address using ⑨,⑧ switch and press ⑩ button to save and store the data. (The one of the 9 preset levels (01~09) are displayed and operated) Start-up setting is ‘Address 01’ and be careful to avoid overlap of an address. (The data is remained whether the system is off) 2) Delegate Unit Start-up setting is ‘Address 11’ and be careful to avoid overlap of an address. Select the Address using ⑨,⑧ switch and press Mode button to save and store the data. (The one of the 90 preset levels (11~99) are displayed and operated. B-2. Procedure of Setup Mode Group Mode(B-3) → Address Mode(B-4) → MAS / SLV Mode(B-5) → TALK VOL ※ MAS/SLV mode is not allowed to the Delegate Unit. Press ⑩ button and ⑦ button at once for about 2 seconds, then Setup Mode will be activated. If press ⑩ button for about 2 seconds, Setup Mode will be finished. Select the Mode or Level using ⑨,⑧ switch and press ⑩ button to save and store the data. B-3. Group Mode Setting Press ⑩ button and ⑦ button at once for about 2 seconds, then Setup Mode will be activated. If press ⑩ button for about 2 seconds, Setup Mode will be finished. Select the Mode or Group using ⑨,⑧ switch and press ⑩ button to save and store the data.

2. Battery Charger Portable Type B-5. MAS / SLV Setting (Stand–alone Mode Setup) For Chairman Unit 2. Battery Charger Portable Type ▶ Stand-alone Mode is for the conference using MIC Stand only without Control Unit. ▶ Select the Master in case of using MIC Stand without Control Unit. The Chairman unit you use independently is allowed to choose the Master. The Voting and Camera location tracking functions won’t be operated during the Stand-alone Mode. ※ You must make the Group change or Controller Power being OFF under Stand-alone Mode. If not, the use of this device can be partially restricted. Select the MAS/SLV Mode accordingly. Choose the Stand-alone MAS/SLV (Master/Slave) using ⑨,⑧ switch. Under MAS mode, the volume of the MIC stand’s inner speaker is level “07” and you can manage the conference using the stand only without the Control Unit. Press ⑩ button, data will be saved and enter the next level. 3. Under Stand-alone (MAS) Mode, ANT is displayed as ANT 2. ▶ Start-up setting is ‘SLV’ mode. (The data is remained whether the system is off) A. Progress : Two Color LED Red ON B. Completion : Two Color LED Green ON C. No Charging : LED OFF