Why Use an instrumentation Amplifier?

Slides:



Advertisements
Similar presentations
Operational Amplifier
Advertisements

Op-Amps and Saturation. The Inverting Mode Op-Amp + - V1V1 VoVo RfRf R1R1 In theory, the gain of the op-amp is given by R f ÷ R 1. This equation works.
Operational Amplifiers
The Inverting Mode Op-Amp. What is the Inverting Mode ? The op-amp can be connected up in various ways or modes. What it does depends on how it is connected.
Operational Amplifiers
CHAPTER 3: SPECIAL PURPOSE OP-AMP CIRCUITS
Lecture Notes Part 4 ET 483b Sequential Control and Data Acquisition
Op-Amp- An active circuit element designed to perform mathematical operations of addition, subtraction, multiplication, division, differentiation and.
Summing Amplifier -+-+ RFRF R4R4 + IFIF I4I4 VoVo R3R3 + I3I3 V3V3 V4V4 R2R2 + I2I2 V2V2 R1R1 + I1I1 V1V1 RLRL V id.
Analog Basics Workshop RFI/EMI Rejection
CMRR Rev 1.0 9/15/13. CMRR Specification Definitions and Equations for CMRR CMRR(dB) = 20 Log (ΔVosi / Δ Vcm) (data sheet) CMRR(Linear-Gain) = 10 (CMRR(dB)/20)
CHAPTER 3 Measurement Systems with Electrical Signals
Chapter 18 Operational Amplifiers. The typical op amp has a differential input and a single-ended output. Class B push-pull emitter follower Diff amp.
Broadcom Proprietary & Confidential. © 2009 Broadcom Corporation. All rights reserved. Input Programmable Gain Amplifier (PGA) Design.
Introduction AD620 Instrumentation Amplifier
Operational Amplifiers (Op Amps) Discussion D3.1.
PH4705/ET4305: Instrumentation Amp Our sensor will be connected to some kind of measurement system either directly, diag. 1, or as a bridge circuit diag.
Instrumentation Amplifier
Instrumentation Amplifiers
Lecture II: Linear Applications of Opamp
Introduction to Op Amps
Part I: Amplifier Fundamentals
“Op-Amp” Operational Amplifier Non Inverting Amplifier Inverting Amplifier Adder –(and Subtractor using an Inverter) Differential Amplifier Integrator.
Introduction to Op Amp Circuits ELEC 121. April 2004ELEC 121 Op Amps2 Basic Op-Amp The op-amp is a differential amplifier with a very high open loop gain.
Analog Electronics Lecture 5.
Instrumentation for Scientists
Announcements Assignment 5 due tomorrow (or now)
Common Mode Rejection Ratio
© 2012 Pearson Education. Upper Saddle River, NJ, All rights reserved. Electronic Devices, 9th edition Thomas L. Floyd Electronic Devices Ninth.
Microelectronic Circuits, Sixth Edition Sedra/Smith Copyright © 2010 by Oxford University Press, Inc. C H A P T E R 02 Operational Amplifiers.
3/1/2003BAE of 5 Additional Information on Op-Amp Specifications.
10/11/2015 Operational Amplifier Characterization Chapter 3.
St Columba’s High School Electricity and Electronics Op-amps.
Module 4 Operational Amplifier
Biomedical Instrumentation I
Unit 8 Operational Amplifier. Objectives: Ideal versus practical operational amplifier Performance parameters Some applications –Peak detector –Absolute.
1 Tai-Cheng Lee Fall 2007 Operational Amplifiers Tai-Cheng Lee Electrical Engineering/GIEE, NTU.
Parameters of OP-AMP M.S.P.V.L Polytechnic College, Pavoorchatram.
Impedance Matching Units. Maximum Power Transfer Theorem As we have seen previously the output of a power amplifier must transfer as much power as possible.
Instrumentation Amplifiers Passive Transducer Measurement Configuration: For passive transducers in a bridge configuration the voltage of interest is the.
Differential Amplifiers
2/June/2009LHCb Upgrade1 Single ended ADC Differential ADC –Convert single ended signal to differential (use AD8138 amp) –ASIC differential output ADC.
Practice Problems 1 P1.17: An FM radio receiver has an input resistance of 75 Ohm. The input signal provided by a distant transmitter is 5 µV rms, and.
Differential voltage-gain device that amplifies the difference between the voltages existing at its two input terminal. An instrumentation (or instrumentational)
Module 2 Operational Amplifier Basics
ARUN MUCHHALA ENGINEERING COLLEGE- DHARI [ ] ANALOG ELECTRONICS Prajapati Omprakash rd ELECTRICAL DEPARTMENT ANALOG ELECTRONICS.
Audio Power Amplifier Detailed Design
Operational Amplifiers
Electronic Devices and Circuit Theory
BIOELECTRONICS 1 Lec 9: Op Amp Applications By
Chapter 10: Operational Amplifiers
PUSAT PENGAJIAN KEJURUTERAAN KOMPUTER & PERHUBUNGAN
Quiz: Determining a SAR ADC’s Linear Range when using Operational Amplifiers TIPL 4101 TI Precision Labs – ADCs Created by Art Kay.
Open book, open notes, bring a calculator
Quiz: Determining a SAR ADC’s Linear Range when using Instrumentation Amplifiers TIPL 4102 TI Precision Labs – ADC Hello, and welcome to the TI Precision.
Operational Amplifier
Quiz: Driving a SAR ADC with a Fully Differential Amplifier TIPL 4103 TI Precision Labs – ADCs Created by Art Kay.
Analogue Electronics Circuit II EKT 214/4
Electronic Devices Ninth Edition Floyd Chapter 12.
The open loop gain of this op-amp is 105 and the bandwidth is 10 Hz
Created by Art Kay & Dale Li Presented by Peggy Liska
Examples of Negative Feedback Applications: A) Inverting Amplifiers
The Ideal Op Amp Inverting and non-Inverting configurations
تقویت کننده های عملیاتی
Lesson 11: Transducer Electrical Interfaces
Chapter 10 Figure 07.
The Ideal Op Amp Inverting and non-Inverting configurations
Amplifiers for high efficiency loudspeakers
MALVINO Electronic PRINCIPLES SIXTH EDITION.
Common-Mode Voltage Input common-mode voltage is the most important specification when selecting a direct current sensing solution. It is defined as the.
Presentation transcript:

Why Use an instrumentation Amplifier? + _ + _ . Classic 3 Op-Amp architecture 2 Op-Amp Architecture To sense the difference between two signals, amplify it, and provide a single ended output. To keep errors low, it should: Þ Reject common mode signals on its inputs Þ Have low offset voltage Þ Have low offset voltage drift The in-amp should also be easy to use and easy to design into your system. a ALP

Why We Beat the Competition The AD623 uses the classic 3 op-amp architecture. The competition uses the two op-amp architecture. AD623 Architecture INA126 Architecture Why is this significant? The AD623 (3 Op-Amp Architecture) provides superior common mode rejection performance over the INA126 (2 Op-Amp Architecture). Look at the results of a simple side-by-side comparison. a ALP

The AD623 Keeps errors Constant AD623 Typical CMRR From this graph you can see that: The AD623 keeps CMV errors constant out to 200MHz. This architecture successfully rejects 60Hz line noise and its harmonics. The common mode rejection performance of the BB INA126 drops off dramatically from 96 dB (typ) at 10 Hz to 72 dB (typ) at 200 Hz! a ALP

Compare the CMRR Performance Side by Side Input Signal (2V Scale) Common Mode Error at the Output (1mV Scale) AD623 G=5 INA 126 G=5 AD623 common mode error = 500mV INA 126 common mode error = 2mV The INA 126 gives you 4 times the error at a higher cost! a ALP

The Competition Gets Worse at Higher Gains! Same Input Signal (2V Scale) Common Mode Error at the Output (10mV Scale) AD623 G=100 INA 126 G=100 AD623 common mode error < 1mV INA 126 common mode error > 20mV The INA 126 gives you over 20x the error at a higher cost! a ALP

More Reason Why AD623 is Better Than BB INA126 Comparison of the AD623 and the INA126 in a typical application* * - 5V common mode signal - G=100 configuration - 20mV full scale signal - .02% resistor matching The AD623 gives you lower cost and lower total error than you can get from Burr Brown! And it’s single supply with rail to rail output! * a ALP

So Why Use The AD623 In Your Application? ALP