Group Members: M. Khayam Shahzad M. Murtaza Farrukh Aneel Abbasi.

Slides:

Advertisements

Similar presentations

X.25 PROTOCOL Presented by : EFA, Daniel Jr. G. VERGARA, Jonvon.

Advertisements

Network Design :1 Fundamentals. 22 Topics Covered Serial and Parallel communication Serial and Parallel communication Demarcation Point Demarcation Point.

EWSD EXCHANGE MEDIATION 2Mbps WAN LINK TOWARDS DATACENTER EWSD SWITCH CISCO 2811 ROUTER X PIN FEMALE X PIN MALE X PIN FEMALEX PIN.

Introduction Computer Hardware Jess 2006 EXPANSION CARDS BUS ARCHITECTURE AND CONNECTORS.

PH4705 ET4305 Interface Standards A number of standard digital data interfaces are used in measurement systems to connect instruments and computers for.

1 Outline Standards Organisations Interface Standards  The RS-232-C Standard  RS-449, RS-422-A, RS-423-A  USB and FireWire.

ECE 371- Unit 11 Introduction to Serial I/O. TWO MAJOR CLASSES OF SERIAL DATA INTERFACES ASYNCHRONOUS SERIAL I/O - USES “FRAMING BITS” (START BIT AND.

Chapter 26 Communication Systems. Objectives After reading the chapter and reviewing the materials presented the students will be able to: Identify common.

PC 232 Serial Ports Ports –Connectors at back of PC –Plus related internal electronics to send/receive PC 232 Serial Port –Follows EIA/TIA 232 standards.

3/17 Parallel and Serial Ports. Roll Call Lecture: –ports –serial ports –parallel ports –USB ports Group Project Information - Handout.

University of Tehran 1 Interface Design Serial Communications Omid Fatemi.

1.5.1 Connecting peripherals. Ports Ports - cont Ps2 – Keyboard and mouse USB(Universal serial bus) – Keyboard, mouse, Printer, Scanner, digital Camera.

Technology Training that Works Hands of Data Communications, Networking & TCP/IP Troubleshooting.

1 Why have we chosen to use the serial port, when it is more complicated and offers fewer connections than the printer port? For a beginners’ course using.

Baseboard Aavikkomursu 7.2. Aavikkomursu Micro- controller Extension port for programming microcontroller and sensor input Resistor RS485 interface chip.

Macquarie Fields College of TAFE Version 2 – 13 March HARDWARE 2.

Serial Port I/O Serial port sends and receives data one bit at a time. Serial communication devices are divided into: Data Communications Equipment (DCE),

Locknetics CIP Module Upgrade 12/2/08 Akin Olugbade Justin Gilstrap Lutalo Webb.

Add on cards. Also known as Expansion card or interface adapter. It can be inserted into an expansion slot of a motherboard to add functionality to a.

1 © 2003, Cisco Systems, Inc. All rights reserved. CCNA 2 v3.0 Module 1 WANs and Routers.

1 © 2003, Cisco Systems, Inc. All rights reserved. CCNA 2 v3.0 Module 1 WANs and Routers.

Line Coding, Modem, RS232 interfacing sequences.

Network Communications: Chapter 3 Introduction to Computer Architecture.

Raymond Giron, Adam Bahr, George Asbeck.  Originally developed by HP in the 1960’s  Wanted an easier way to interface the instruments and controllers.

Electronic Communication Understanding Serial Communications in Manufacturing.

Electronic Circuit Diagrams

1 Chap. 3 Interface. 2 Interface  Physical connection between node and transceiver  Network interface card (NIC)  Physical connection between transceivers.

Serial Interfaces Oct 3, Announcement We will discuss the test at the end of tonight’s lecture. No homework Chap. 9 is not required to be read.

1 Transmission of Digital Data : Interface and Modems.

Digital Interfaces An interface links two devices Interface Standards define: – mechanical specifications - how many wires & connector type –electrical.

Programmable Logic Controllers

การส่งข้อมูลผ่าน PSTN

EIA-449 Standard By- Vineeta Shakya

1 © 2004, Cisco Systems, Inc. All rights reserved. CCNA 4 v3.1 Module 3 PPP.

CSC 335 Data Communications and Networking Lecture 4b: Communication and Multiplexing Dr. Cheer-Sun Yang.

Feb. 16, 2004 Prof. Paul Lin 1 CPET 355 RS 232 Serial Communication Paul I-Hai Lin, Professor Electrical and Computer Engineering Technology Purdue University,

1 Pertemuan 2 Routers. Discussion Topics Introduction to WANs Router physical characteristics Router external connections Management port connections.

Ports and Connectors By Karina Hackett Overview: Ports are also known as sockets, and are located at the back of a system unit. Connectors are the parts.

Lecture 3 EIA 449.

Keyboard Introduction Keyboard is an input device. It is used to give text, numbers and controls as input to computer. The.

9/11/14 Objectives: To disassemble and assemble a desktop computer.

Chapter 4 Making Connections. Modem Modulates digital data onto analog signal and then demodulate analog signal back to digital data Features:  Standard.

BATCH MEMBERS R.ABHISHEK-08N41A0401 K.DHEERAJ REDDY-08N41A0412 S.RAJENDRA REDDY-08N41A0458 JYOTHISHMATHI COLLEGE OF ENGINEERING AND TECHNOLOGY,TURKAPALLY.

NARNARAYAN SHASTRI INSTITUTE OF TECHNOLOGY Prepared by: Wasu Ichcha kaur H Bhalani Nidhi M Dhakate Megha D MICROCONTROLLER.

Introducing Hardware.

Electrical Engineering

RS-232 Communications.

Chapter 7: Introduction to Data Communications and Networking

6장 Transmission of Digital Data: Interfaces and MODEMs

Components of Computer

DATA COMMUNICATION Lecture-22.

Multivariable Serial Interface

Modem acronym for modulator-demodulator

Serial Communications

C_ITCO011/C_ITCO111 LECTURER: E.DONDO

DATA COMMUNICATION Lecture-21.

Local Asynchronous Communication (RS-232)

COMMON LAYER 1 DEVICES AND FUNCTIONALITIES.

Universal Serial Bus Specification 1.0

CCNA 4 Chapter 2 PPP.

Identification And Function

Serial Communication Interface

ECEN “Internet Protocols and Modeling”

ANEEL ABBASI MUHAMMAD ADNAN MOIZ SHAH MUHAMMAD KHAYAM GROUP MEMBERS.

CCNA 2 v3.1 Module 1 WANs and Routers

Chapter 6 Transmission of Digital Data Interfaces and Modems

RS-422 Interface.

ANALOG AND DIGITAL PHYSICAL INTERFACES

Figure Serial versus Parallel Data Transfer

Chapter 6: INTERFACES Visit for more Learning Resources.

Presentation transcript:

Group Members: M. Khayam Shahzad M. Murtaza Farrukh Aneel Abbasi

Electrical Standards & RS232

Introduction: This section introduces the RS232 serial standard. This is a standard that is used to connect serial devices like modems to the PC. The main features and signals of the standard will be covered.

The RS232 standard: Specifies a 25 pin connector as the standard interface in data communication networks. Lettering pin designations for ground, data, control and timing circuit.

The RS232 Connector: Two main categories: Male connector. Female connector.